Description

 

Compact ZYNQ7020 DEV Development Board Kit FPGA Development Board with FMC and LPC Interface

Master Chip Parameter:
- Model: XC7Z020-2CLG484I
- Chip level: industrial level
- PS application processor model: for ZYNQ on-chip hardcore processor, dual-core Cortex-A9, main frequency of 766M
- DDR specification and model: 512MByte, 16bit width, 1066M data rate, MT41K256M16TW-107
- Logical unit (LC): 85K
- Lookup table (LUT): 53200
- DSP unit multiplier: 220pcs
- Trigger (Flip Flops): 106400
- Ram: 4.9Mbit
- Temperature range: -40℃ ~ 85℃
- Speed level: -2

Development Board Functions and Interfaces:
- Power supply mode: TYPE-C interface, 9-12V DC-IN interface
- Development board clock resources: 33.33M (PS), 50M (PL)
- Ethernet: Gigabit RTL8211E, RGMII interface, one PS, one PL
- USB interface: USB2.0, PS terminal, support for HOST and SLAVE function
- Debugger: onboard UART+JTAG downloader, supporting all development of ARM and FPGA.
- SD card: SD0 of PS, support for boot (SD support up to 32G)
- HDMI-compatible interface: one HDMI-compatible mini output, maximum support 1080 at 60Hz.
- LED: one PS pin button, two PL pin button; 2 PS LED, 4 PL LED
- Power-on setting switch: a BOOT dial switch used to start setting
- Buttons: two PS buttons and one PL button, one reset button
- Start setting switch: a BOOT dial switch used to start setting
- Onboard OLED module: 0.96-inch 128x64 mono OLED, SPI interface, based on PL
- Camera interface: one MIPI CSI camera module
- Onboard FLASH: W25Q128FVSIG, 128Mbit (16Mbytes)
- 40-Pins expansion IOs: including 34 single-end IO ports, BANK13, 3.3V power supply
- System reset: one system reset (POR) button
- Development board indicator: DONE, USNCPEN, power input indicator
- Development board power supply system:
  Onboard inner-core power supply: 1.0V/6A
  Others: 1.8V/3A, 1.5V/3A, 3.3V/3A
  FMC BANK34 35 power supply: 2.5V/3A
  Expansion IO port 40P BANK13 power supply ADJ2: 3A/3.3V
- Note 1: it can provide power supply in Type-C except for DC-IN, all other TYPE-C are suspended and have no power supply function.
- Note 2: FMC using BANK34 35 as HR BANK, and only 2.5V ADJ1 voltage supports LVDS_25 differential standard.
- Note 3: 40P using BANK13 as HR BANK, and the design is single ended signal.

AD9361 Main Chip Parameter:
- Main chip model: AD9361bbcz
- RF range: 70MHz - 6.0GHz
- Signal data bandwidth: 200K - 56MHz
- Transceiving channels: 2 receiving and 2 transmitting, and quadrature modulation, support simultaneous transmission of 4 groups of data

RF Part Functional Interface Parameter:
- FMC type: standard FMC LPC interface, compatible with HPC
- Antenna interface: SMA female connector
- Clock: onboard 40MHz/5ppm passive crystal oscillator, support SMA external clock
-Power monitor: 2 TX_MON interfaces, SMA female connector
- EEPROM: one FM24C02 EEPROM
- RF front-end balun: model TCM1-63AX+, bandwidth 10MHz-6.0GHz
- PCB wiring: all data interfaces are differential, and all other control signals are single ended and of equal length.
- Sub card power supply: 3.3V power supply from FMC interface; and IO interface power supply from ADJ
- RF LDO linear power supply: wireless LO power supply 1.3V/1.5A power supply 2-channel LDO
- PCB RF impedance: 50ohms
- PCB size: FR4, 1.6mm (thickness), 10 layers PCB

Package Included:
- 1 x Development Board
- 2 x Type-C Data Cable
- 1 x Common Acrylic Board
- 1 x Front Anti-static Acrylic Board (onboard)
- 4 x Nylon Stud (onboard)
- 1 x 9/12V Power Adapter
- 1 x USB Type-C to A Adapter
- 1 x Mini HDMI-compatible to Standard HDMI-compatible Adapter

Note:
- AD9361 Mini sub card is not included.