eBay

Pattern Vinyl Transfer Sticker
Iron on Vinyl HTV Heat Transfer
Professionally Crafted and Printed in the USA
Silhouette Cameo, Roland, Siser, Cricut Cutting Machine Compatible

Indoor/Outdoor Adhesive Vinyl Sticker | Iron on Vinyl HTV

Buy More, Save More
Bundle discounts available!

Cut out any shape or design & apply!

Take advantage of our huge selection of patterns & colors!

Please be sure to check out the easy application instructions below!

All you need is a plotter or cutter! Iron for HTV
All Patterns are printed with a large format Roland printer that uses Eco-solvent genuine inks.

Permanent Adhesive Craft Vinyl (Outdoor/Indoor Vinyl)

Great to use on glass, metal, plastic, and much more! Please clean surface before use!
Cut on Pattern Side and DO NOT MIRROR. After weeding excess vinyl, apply a
transfer tape to transfer design off of the backing and place on your smooth & clean surface
Weatherproof / 5+ years durability

Removable Adhesive Craft Vinyl (Indoor Vinyl) Reusable Stick & Peel Vinyl
Apply, Remove & Apply Again! No Residue when peeling!

Great to use on walls, glass, metal, plastic, and much more! Please clean surface before use!
Cut on Pattern Side and DO NOT MIRROR. After weeding excess vinyl, apply a transfer tape to transfer design off of the backing and place on your smooth & clean surface
Wallpaper Vinyl / 7+ years durability

Iron on Vinyl HTV for T-Shirts, Garment & Apparel (Heat Transfer Vinyl Mask or Tape Provided)

Heat Transfer is printed without the carrier. Easy Transfer Mask provided for application
Cut on Pattern Side and DO NOT MIRROR. After weeding excess vinyl, apply Easy Transfer Mask to transfer design off of the backing and place on your garment face up
Can be applied with a home iron and/or heat press

CUTTER SETTINGS
Cricut: Blade: Standard Setting: Iron On	Silhouette Cameo: Blade: Standard, 3 Material: Heat Transfer, Smooth Speed: 8 Force: 6		Scan N Cut: Blade: Standard, 2 Cut Speed: 1 Cut Pressure: 1
Roland GS/GX-24: Blade: 45° Gram Force: 80-90 Offset: 250 Speed: 25-50 cm/s	Graphtec: Blade: 45° Gram Force: 9 Tool: CB09U+0 Speed: 25 cm/s	MH, SC2, LP3, & Titan 1: Blade: 45°/60° Gram Force: 80-85 Speed: 300mm/s *Blade Advancing Varies	Titan 2 & 3 Blade: 45°/60° Gram Force: 60-65 Speed: 300mm/s *Blade Advancing Varies
Settings may vary based on blade condition and age of machine. Always perform a test cut prior to cutting designs.

APPLICATION INSTRUCTIONS

Application Instructions (home iron)
Set iron dial between Cotton and Linen
Cover design with Kraft paper or non-stick cover sheet
Place on flat, hard surface (ironing board not recommended)
Press iron with medium/firm pressure (do not slide iron)
Press each section of design for 15 seconds
If areas of design lift after application, replace cover sheet
and re-press for 10 seconds
Peel carrier hot or cold

Application Instructions (heat press)
Cut material - don't mirror!
Weed excess material
Mask with our Easy Transfer Mask
Preheat garment for 2-3 seconds
Apply design at 305°F/150°C
Use medium pressure for 10-15 seconds
Peel carrier hot or cold
Cover and reheat for 2-3 seconds

RECOMMENDED ACCESSORIES & CARE
Patterned Vinyls Apply to: 100% cotton Poly/cotton blends 100% polyester Leather Lycra®/spandex	Recommended Accessories: Weeder/Tweezers		Laundering: Wait 24 hours before 1st wash Machine wash cold / mild detergent Dry on normal dryer setting Do not dry clean Do not bleach

SIZE AND HOW TO APPLY
	1) Do not mirror 2) Cut on pattern 3) Weed excess vinyl 4) Apply and peel mask 5) Press
	1) Do not mirror 2) Cut on pattern 3) Weed excess vinyl 4) Apply and peel mask

CUSTOM PATTERNS AND DESIGNS

Have your own patterns you want to print?
Contact us today!