This listing is for 100ml of Metal-Tec10 (bottle size approx. 4" high) which will treat approximately 2 litres of oil as an additive.
For automotive or industrial use, add Metal-Tec10 at the rate of 5% by volume to any oil or grease to reduce friction, heat and wear and increase efficiency. MetalTec-10 flattens metal surfaces to increase lubrication and reduce drag (friction). There are many other oil additives on the market that act in a similar way but, unlike the others, Metal-Tec10 contains no chlorinated hydrocarbons and is PH neutral, protecting the metal surfaces against acid erosion which occurs when chlorinated hydrocarbons mix with water droplets and moisture to form hydrochloric acid. Metal-Tec10 contains no PTFE, silicone, graphite, moly or solid lubricants.
Here is a review from an eBay customer who purchased MetalTec-10 from us in 2010 and has since been back for more:
Reviewer: Paul Gascoyne from Sheffield
This stuff really works. I own a Jeep Grand Cherokee Orvis, I had a power steering line come loose and the fluid drained out. I have an illness that makes it difficult for me to walk so I drove the car home. I repaired the leak and refilled the system with the best power steering oil I could get for the car, bled the system and took it out for a run. The steering was notchy and rough, it also was very slow on returning to centre. I ordered one of these additives and when it arrived I drained out some of the oil and added the whole bottle. I must admit I added 25ml more than I should have - I put the whole bottle in. Well after only a couple of hundred miles the steering is transformed. It has lost the notchy feel, goes where I put it and is just - well nice to drive, better than it was before the oil drained out to be honest. I have also noted that it keeps getting a little better as the miles add up. By the time I get to the 1k marker I will probably need surgery to remove my smile. It has saved me two days hard work and God knows what in money. If your system will not respond to this stuff then it's beyond help. My thanks to the team. I will be back for other additives. Paul
Advanced Technology Metal Treatment, Anti-Friction Lubricant Additive
Ametech Metal-Tec10™ is an advanced technology, anti-friction lubricant additive, consisting of a blend of the highest quality petrochemical products. It is a PH neutral maximum duty, metal conditioning formula especially recommended for use in lubrication systems where there is a special concern for extra protection due to extreme pressure, friction-related heat and high-wear conditions. Metal-Tec10™ contains no chlorinated solvents, PTFE, silicone, graphite, moly or solid lubricants. Metal-Tec10™’s formula allows it to blend well with all types of petroleum and most synthetic lubricants (but not vegetable oils or esters), enhancing the performance of both.
Ametech Metal-Tec10™ can be used in conjunction with AMETECH ENGINE RESTORE OIL providing it is added after the RESTORE oil has been in the engine for 1000 miles. Metal-Tec10™ has been formulated to increase the efficiency and performance of your automobile, truck or commercial vehicle. But in order to obtain the full benefit of the product, it requires dedicated interest on your part to follow product directions and take proper care of your vehicle. Oil changes, oil filters, gas filters, good grades of fuel, proper lube jobs, tune ups and qualified auto technicians performing maintenance and repairs all pay dividends toward the annual expense and the life of your vehicle.
Ametech Metal-Tec10™ Metal Treatment is recommended for these automotive applications:
Advantages
One of the biggest enemies of a transmission is heat. The amount of heat present in the system will normally dictate the lifetime of that transmission. When Ametech Metal-Tec10™ is added, heat is significantly reduced. Metal-Tec10™ addresses the extreme-pressure (EP) areas, such as planetary and worm gear systems, along with bushings, bearings and shafts.
VALVE BODY OPERATION: In many cases presented by professional transmission builders, Metal-Tec10™ has freed the valve body and maximized performance with no recurrence of sticking or intermittent hang-ups.
GOVERNORS: As most transmission builders are aware, there are certain governor systems that have unique tendencies to hang up for no apparent reason. Two reasons these hang-ups occur are contaminants and microscopic spiking of the metal due to electrolytic corrosion of the metal. Ametech Metal-Tec10™ will displace contaminants and smooth and seal metal surfaces, removing electrolytic spikes and preventing their formation.
Advantages
* Although Metal Tec10™ reduces friction, it has no negative affect on the sprag or clutch friction necessary for the operation of the transmission. As confirmed by Raymark in a letter of October 1986 in testing their SAE clutch pack: "The results of our test indicate no change in the friction levels, thus we do not expect the addition of your additive to have a negative effect on our friction products."
Advantages
*If you are experiencing difficulty with the unit, we recommend the unit be thoroughly flushed prior to the addition of Metal-Tec10™.
Advantages
NOTE: Limited slip additive is still required with the use of Metal-Tec10™.
Carried to the moving metal parts by the fluid to which it is added, Ametech Metal-Tec10™ creates a boundary film which smoothes and seals metal surfaces to reduce friction and friction-related heat. This results in less wear and smoother operation of the mechanism with no danger of build up or changes in tolerances. The end result is improved operation of the system.
Ametech Metal-Tec10™ improves the overall tribological properties of the metal surfaces. Film strength is a function of surface roughness and viscosity. The smoother the surface, the higher the film strength, while viscosity can be lower to improve fluid flow conditions.
Ametech Metal-Tec10™ treated surfaces will increase fluid film strength, reducing friction, heat, wear and energy consumption. This returns efficiency and previously wasted energy back to the system for increased power. This process, combined with the physical surface improvement of the metals, steps up oil flow, reduces metal film strength, improves the shear strength of the base lubricant, and results in an overall reduction in friction and friction-related wear.
Ametech Metal-Tec10™ is extremely concentrated and effective even in small quantities. Add 5% Metal-Tec10™ by volume to transmission oil, i.e. 50ml to every 1 litre of oil.
Metal-Tec10™ can also be applied directly to parts while rebuilding and can be sprayed in a fine mist directly onto the parts you want it to reach or sprayed onto greases to facilitate blending.
For Hydraulics - Add 25ml Metal-Tec10™ to every 1 litre of oil.
One Litre bottle of Ametech Metal-Tec10™ will treat approximately 20 litres of oil. This handy bottle with applicator nozzle contains 100ml of Ametech Metal-Tec10™ which is sufficient to add to 2 litres of oil.
IMPORTANT: Metal-Tec10™ should not be used in CVT gearboxes. CVT (Constant Variable Transmission) oil or fluid improves the friction/grip between rubber/metallic belts and alloy/composite pulleys, whereas Metal-Tec10™ reduces friction between metal-on-metal components, spool valves & spindles lubricated by ATF (automatic transmission fluid) in automatic transmissions. As these requirements are opposed, neither ATF nor Metal-Tec10™ should be used in CVT rubber/metal belt transmissions.