1) remote interchangeable with remotes in stock # 536

2) Check bin thoroughly to match the condition described.

 

See pictures for an example of what you will receive.

One (1)

Aftermarket Security Installed System remote 

keyless entry fob alarm controller

Transmitter control clicker keyfob controller replacement

Audiovox / Prestige / Pursuit / Pro

 FCC ID: ELVAT0E

(Alternate Spelling: ELVATOE )

 Part #: PROOE4BS

 (Alternate Spelling: PR00E4BS )

Interchangeable Part #’s:

PROOE4

PROOE4B

PROOE4BS

PROOE4BS41

APS2K4MS50

APS2K4SBCF

PROOE4BSUG

 

Circuit Board #: AT9G or ATDG

LED LIGHT: Red

Buttons: 4

Frequency: 433 -434 MHz (433.92)

Battery: 1; GP27A

See Item Specifications for more details

 

Compatible With the following Aftermarket installed security systems:

PRO9675FT4

PRO-9775

PRO-9800

PRO-9349FT

PRO-98BTKD

PRO9275T

SS-CIT-1

APS686

APS786

APS800

 

 

APS995C

APS995R

APS996

APS996A

APS996C

APS800C

APS875

APS875C

APS995

APS995A

 

 

 

Programming Instructions:

 NOTE: It is important to remember that during the programming mode, each individual step must be completed within 15 seconds of the previous step. If the 15 second time limit expires between steps, the unit will automatically exit the program mode. This is indicated by a long chirp from the siren.

Non alarm models will flash the parking lights only to confirm the transmitter code has been learned and stored.

NOTE: Because the system may be capable of sounding a siren, the vehicle horn, or both, where the siren chirp is referenced below, the siren may chirp, the horn may beep, or both devices may sound.

TO PROGRAM ADDITIONAL TRANSMITTERS:

1) Enter the vehicle, and turn the ignition switch to the on position.

2) Press and release the valet push button switch three times.

Note: Some systems may use a combination push-button LED switch. In these systems the push-button and the dash mounted LED are one and the same.

3) The dash mounted LED will flash 1x, and the siren will chirp 1x, indicating that the system is ready to accept programming of channel #1 which is arm/lock, disarm/unlock/unlock 2, and panic functions.

4) Press and hold the lock or lock/unlock symbol button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren.

"Repeat step 4 for each transmitter you wish to program".

NOTE: If your transmitter button has the Lock/Unlock icon on one button, press and release the valet push button switch 2 times then move on to step #8.

5) Press and release the valet push button switch one time to advance to channel 2. The siren will chirp 2 times and the dash mounted LED will Flash 2 times, indicating that the unit is ready to accept programming for channel # 2 which is only used for separate lock and unlock button transmitters, and is the disarm/unlock/unlock 2 and panic.

6) Press and hold the unlock symbol button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren.

"Repeat step 6 for each transmitter you wish to program".

7) Press and release the valet push button switch one time to advance to channel 3. The siren will chirp 3 times and the dash mounted LED will Flash 3 times, indicating that the unit is ready to accept programming for channel # 3 which is the trunk release/alternate output channel of the system.

8) Press and hold the trunk/key symbol button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren.

"Repeat step 8 for each transmitter you wish to program".

9) Press and release the valet push button switch one time to advance to channel 4 if so equipped. The siren will chirp 4 times and the dash mounted LED will Flash 4 times, indicating that the unit is ready to accept programming for channel # 4, optional device (where equipped)

10) Press and hold the Option button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren.

"Repeat step 10 for each transmitter you wish to program".

11) Press and release the valet push button switch one time to advance to channel 5 if so equipped. The siren will chirp 5 times and the dash mounted LED will Flash 5 times, indicating that the unit is ready to accept programming for channel # 5 optional device (where equipped)

12) Press and hold the second Option button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren.

"Repeat step 12 for each transmitter you wish to program".

 

 

How to find out if this remote is compatible with your Vehicles’ installed RKE System

If you're not sure your vehicle can use this remote, please ask questions or contact your local dealer first.

1.   Check the back of your current or old keyless remote to match FCC ID /Part #’s.

2.   Contact your local dealer and tell them your VIN# and ask what part # / FCC ID you need.

 

Your vehicle will be installed with one of the following keyless entry systems:  

  a. Standard Keyless Remote Packages: Installed at time of manufacture. 

  b. Optional Keyless Remote Packages: Installed by a dealer. 

  c. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop. 

  d. No remote keyless entry system at all.

The above information can change which remote you need
for your installed remote keyless system
.

We ensure proper working condition of all previously used or new remotes through a serious of tests performed with the Santronics Testing device. Each button is tested for functionality prior to shipment and then logged.

Please Note: Each remote and circuit board is UV id’d prior to shipment  – All returns receive a UV ID inspection to verify originality of remote sent prior to refund or replacement.

Does this keyless remote entry come with a battery?  

Yes. It will have a working battery installed.

Battery Condition:

        A. All remotes sold on Keyless4u include working batteries.

        B. Installed batteries are not tested for battery life- they are simply working.

             Some are new and some are used.