Maxed out NerdQaxe++ rev7 miner with full copper, cooling stand and premium fans
This is a maxed out Solo Satoshi Bitcoin mining rig complete with a custom cooling tower, Honeywell PTM7950 Phase Change Thermal Pad upgrade for all ASICs, full copper heatsinks on all ASIC and VRM modules, including rear board hotspots, a 120mm shroud with VRM cooling duct and 120x25mm Noctua premium fans both front and rear.
Miner has been taken to 975MHz and still had a more to give! This is a fairly new rig, ~1 month old.
Upgrades included with this rig:
- Axeforge Cooling Stand from eBay vendor axeforgetechnologies (https://www.ebay.com/itm/327300098219)
- NQ-HELIX 120mm fan shroud for NerdQAxe series APX90 X36 X47 X53 with VRM cooling duct from eBay vendor boostedlexus3 (https://www.ebay.com/itm/317978292539)
- Honeywell PTM7950 Phase Change Thermal Pad upgrade for all ASICs
- BitcoinMerch Full Copper Heatsink
- Pure copper heatsinks for VRM's and board hotspots (front and back)
- Noctua premium 120x25mm fans (1 front / 1 rear)
- Mean Well LRS-150-12 Power Supply (fully wired)
What's in the box:
- Maxed out Solo Satoshi Bitcoin mining rig
- Mean Well LRS-150-12 power supply (fully wired)
- Original power supply brick from Solo Satoshi*
- How to setup your miner (instruction card)
* While you can use their power brick, the LRS offers more stable, clean power - crucial for overclocking
I'm selling it for $215 + Shipping. This about what you would pay just for the Solo Satoshi rig alone, minus the stand, rear fan and any upgrades. Please do your own research, but I promise you - its a GREAT deal!
********************
What is the Solo Satoshi NerdQaxe++ Rev 7
The NerdQaxe++ Revision 7 is an open-source, quad-chip Bitcoin solo miner with four BM1370 ASICs. Stock performance is approximately 4.8 TH/s at 69.5W. Each unit is assembled, tested, and flashed with Nerd*OS in the USA
Revision 7 replaces the earlier power-delivery design with a TPS546D24A two-phase voltage-regulator configuration derived from the Bitaxe GT. It includes a 1.9-inch LilyGO color display and runs Nerd*OS, an ESP-Miner-based firmware interface for setup, pool configuration, monitoring, firmware updates, and tuning.
What’s New in NerdQaxe++ Revision 7
Revision 7 is a power delivery redesign. The voltage regulator circuit now uses the same configuration as the Bitaxe GT, delivering cleaner voltage under load and more overclocking headroom.
- Bitaxe GT Voltage Regulator Configuration: New VRM layout provides more stable power to all four BM1370 ASICs. This improves efficiency, thermal performance, and long-term component lifespan.
- Relocated Temperature Sensors: Voltage regulator circuit sensors are repositioned for more accurate VRM temperature readings.
- Higher Overclocking Ceiling: Stable overclocking reaches 1000MHz / 1330mV, delivering over 8 TH/s at 140W (with modifications).
- Revision 7 also includes: XT30 power input (15A rated), 1oz copper traces, spring-mounted heatsink, fuse-free design, 2mm FR-4 PCB, and the 1.9″ LilyGO color LCD.
NerdQaxe++ Revision 7 Technical Specifications
Specification Details
Model NerdQaxe++ Revision 7
ASIC Chips 4× Bitmain BM1370 (S21 Pro)
Hash Rate (Default) ~4.8 TH/s (±15%)
Hash Rate (Overclocked) ~8.1 TH/s (±15%)
Power Draw (Default) ~69.5 W (±15%)
Power Draw (Overclocked) ~140 W (±15%)
Efficiency (Default) ~14.48 J/TH (±15%)
Efficiency (Overclocked) ~16.28 J/TH (±15%)
Voltage Regulator TPS546D24A two-phase (from Bitaxe GT)
Algorithm SHA-256
Power Connector XT30 (supports up to 15A)
Input Voltage 12V DC
PCB Thickness 2mm FR-4
Display 1.9″ LilyGO LCD (color)
Connectivity Wi-Fi 2.4GHz
Fuse None (fuse-free design)
Firmware Nerd*OS (esp-miner fork)
Fan Control Automatic or Manual
Dimensions 3.54″ × 4.72″ × 1.57″
Weight (rig only) ~1 lbs with heatsink
Assembly USA
Shipping weight 6 lb