FCC ID: N14TMTX-1 N14TMTX1 Ni4TMTX-1 Ni4TMTX1 N14TMTX-i N14TMTXi Ni4TMTX-i Ni4TMTXi

DENSO TMTX-1

3 Buttons:

Lock / Unlock / Panic

See Item Specifications for more details

Compatible Vehicle’s

1999 2000 2001 2002 2003 for Lexus RX300

Programming

ATTENTION: This remote key requires a TWO PART programming process:

PART #1:

Programming Instructions for Remote Control (Lock & Unlock your vehicle doors etc.):

TRANSMITTER PROGRAMMING

NOTE: The remote keyless entry system is equipped with 2

transmitters, having 2 unique vehicle access codes programmed

into the wireless door lock ECU.

MODES OF REGISTRATION (PROGRAMMING the Remote)

There are 4 registration modes:

Add Mode

Adds a transmitter (remote) without erasing existing transmitter

codes. Four transmitter codes can be registered at one time. If number

of registered codes exceeds 4, previously registered codes are erased

in order, starting with first registered code.

Rewrite Mode

Erases all previousLy registered transmitter codes and

reprogram new transmitters.

Confirmation Mode

Informs user of number of existing transmitter codes already

programmed in system.

Prohibition Mode

Erases all existing registered transmitter codes and cancels

wireless door lock operation. Use this function if transmitter is lost

or stolen.

REGISTRATION OF RECOGNITION CODE

1) To begin programming, remove key from ignition switch.

Ensure driver's door is open and unlocked, and all other doors are

closed. Insert key into ignition switch, and then remove it.

2) Complete the following in 40 seconds or less: press door

lock switch (the one that controls all the locks) to LOCK position,

and then within one second, press door

lock switch to UNLOCK position. Repeat procedure continuously until

door locks have been locked and unlocked 5 times. Close, and then open

driver's door.

3) Complete the following in 40 seconds or less: repeat

procedure in step 2), except for closing and opening driver's door.

Insert key into ignition switch. To enter desired mode, turn ignition

switch to ON position and back to LOCK position (one cycle), within

one second, the specified number of times. See REGISTRATION MODE

SELECTION table below. Remove key from ignition switch. Registration

of confirmation code is complete after door locks cycle. Be sure to

continue as below.

REGISTRATION MODE SELECTION

----------------------------------------------------------------------------

Mode - - - No. Of Ignition Switch Cycles

Add = 1

Rewrite = 2

Confirmation = 3

Prohibition = 5

----------------------------------------------------------------------------

4) If any mode, other than confirmation mode is selected, go

to next step. If confirmation mode was selected, door locks will cycle

0-4 times depending on how many transmitter codes are stored in ECU.

Example: two stored codes equals 2 door lock/unlock cycles.

5) Complete the following in 40 seconds or less: if add mode,

rewrite mode or prohibition mode is selected, to confirm proper

initiation, door locks will automatically cycle one time for add mode

(at the end of step 3),

2 times for rewritemode and 5 times for prohibition mode. Press

transmitter LOCK and UNLOCK buttons simultaneously for at least 1.5

seconds, and then within 3 seconds, press any transmitter button for

at least one second.

6) If within 3 seconds, door locks cycle one time, new

transmitter code has been successfully accepted. Go to next step. If

door locks cycle 2 times, new transmitter code was not accepted. To

program an additional transmitter or to make a second attempt, return

to step 5) within 40 seconds.

7) Registration of recognition codes is complete under any of

the following conditions:

* Forty seconds has elapsed since wireless door lock ECU has

responded.

* Driver's door is closed.

* Key is inserted into ignition key cylinder.

* Four recognition codes are registered at one time.

PART #2:

Programming Instructions for Transponder Chip:

the manufacturer’s programming instructions For your vehicle make model and year specify diagnostic programming required

This keyless entry's TRANSPONDER CHIP requires programming by your local dealer or locksmith. The procedure takes a few seconds to complete so many dealers will do it as a courtesy. If your dealer does charge a fee, local locksmiths usually charge much less.

You will need to visit your local dealer or locksmith to have your remote programmed to your car using diagnostic equipment

LOCKSMITH = Least expensive….