Why purchase a recycled keyless entry remote transmitter?
The vehicle keyless remote key fob you are going to purchase from us is pre-owned; aka: used, previously loved ;). We recycle OEM and aftermarket keyfobs and put them through a concise refurbishing process so we can guarantee our products are delivered to you in a ready-to-program state. We offer these car clickers at a significant cost savings to stealerships so you can keep your hard earned cash for something more fun while lightening your ecological footprint J. We call that a win-win! Why wait? Add some convenience to your daily routine and help save the environment, order your recycled car remote control today!
What are you purchasing?
This is ONE (1) Factory OEM (Original Equipment Manufacturer) keyless entry remote, aka "key fob" that will work with your OEM Factory installed RKE system.
Compatibility: Works with vehicles that use a factory keyless entry system listed in our compatibility section above AND below.
|
FCC ID#(s) |
FCC ID FCCID M3N65981403 |
|
Alternate Spellings |
M3N6598i403 M3N659814o3 FCCIDM3N65981403 FCC IDM3N65981403 |
|
Part #(s) |
PN: 10372541 Driver Memory #1 1 ONE PN: GM/S:10372542 GM/S:10372512 |
|
Dealer #(s) |
Driver Memeory Memory 1 2 1 #2 #1 one two |
|
Compatible Vehicles FOR THIS FCC ID / PART # |
2005 2006 2007 05 06 07 Chevy Chevrolet Corvette |
|
Button Count |
: Unlock, Lock, TRUNK Opener Release, Panic Alarm Horn |
|
Battery (installed) |
1; CR2032 |
|
Frequency |
315 MHz (315MHz) |
|
Programming: Please note not all customers will be able to complete the programming on their own so if you are having trouble or unsure diagnostic programming is available at your local qualified automotive locksmith or car/audio shop. |
How to Program a 2005 Chevrolet Corvette Keyless Entry Remote Fob Smart Key
Step by Step How to Programming Instructions:
Programming with a recognized Transmitter: Canadian owners see locksmith or dealer. IMPORTANT: This procedure is not available when the
maximum number of 4 fobs have been programmed. If 4 key fobs are programmed
to this RCDLR and this method is attempted, the driver information center
(DIC) will display, MAX FOBS LEARNED and the programming procedure will exit.
1. The vehicle must be off. 2. Place a known key fob and the new un-programmed key fob within the interior of the vehicle. 3. At the rear of the vehicle, insert the vehicle
key into the rear compartment lock cylinder, located above the license plate.
Open the trunk and cycle the key 5 times within 5 seconds. 4. The DIC will display: READY FOR FOB X (X = fob 2, 3, or 4). 5. Place the new un-programmed key fob in the glove box fob pocket with the buttons facing passenger side. 6. A beep will occur and the DIC will display: READY FOR FOB X (X = fob 3 or 4) or MAX FOBS LEARNED. 7. Press the OFF/ACC portion of the ignition switch to exit programming mode. 8. Test remote.
Programming without a recognized Transmitter: Canadian owners see locksmith or dealer.
1. The vehicle must be off.
2. Place the new un-programmed key fob in the glove box transmitter pocket with the buttons facing passenger side.
3. At the rear of the vehicle, insert the vehicle key into the rear compartment lock cylinder, located above the license plate. Open the trunk and cycle the key 5 times within 5 seconds.
4. The DIC message will display OFF-ACCESSORY TO LEARN.
5. Press ignition switch.
6. The DIC will read WAIT 10 MINUTES and will count down to zero, one minute at a time.
7. The DIC will display OFF-ACCESSORY TO LEARN again.
8. Press ignition switch.
9. The DIC will read WAIT 10 MINUTES and will count down to zero, one minute at a time.
10. The DIC will display OFF-ACCESSORY TO LEARN again.
11. Press ignition switch.
12. The DIC will read WAIT 10 MINUTES and will count down to zero, one minute at a time.
13. A beep will sound and the DIC will read READY FOR FOB #1. At this time, all previously programmed key fobs have been erased.
14. Once the key fob is recognized and programmed, a beep will sound and the DIC will display READY FOR FOB #2.
15. If you have additional key fobs to program, take key fob #1 out of the transmitter pocket and place key fob #2 in the pocket. This can be done repeatedly until up to 4 key fobs have been programmed. The DIC will then display MAX # FOBS LEARNED and will exit the programming mode.
When you are done programming key fobs press the ignition switch. |
|
Condition Notes |
Pre-Owned; ready to be programmed to your vehicle’s compatible factory installed RKE system |
Installed RKE System Type:
Please be sure you have a FACTORY (RKE) remote keyless entry system. It was not standard on all vehicles. If your current remote looks the same then this will work. Other options include: Dealer Installed or Aftermarket. The system installed in your vehicle will CHANGE the required remote. If you are unsure ask your local dealer they will need your VIN # (Vehicle Identification Number (located on our vehicle registration car, on your driver side door jam, or your windshield (lower left drives side))).
Why does your vehicles installed RKE / Security system determine which remote control your can purchase?
The remotes job is to pair with your vehicles installed RKE system. It will only sync to a matching system; therefore, you cannot purchase a different type of remote than the remote manufactured with the system. It will not pair with a foreign system.
Programming:
We will send you information on how to locate programming requirement/instructions for your make, model, and year vehicle. Some vehicles have DIY (do-it-yourself) programming instructions available. While other vehicles require diagnostic programming which is available at your local qualified automotive locksmith or dealer.
Programming Requirement Information NOTE:
The vehicle manufacturers determine the programming requirements at the time of manufacture. We pass the programming requirements / instructions on to you as a courtesy. We do not write the programming nor do we determine which vehicles require diagnostic programming and which vehicles can be programmed by the you (DIY). We are not locksmiths nor mechanics nor are we familiar with EVERY vehicles program sequence. If you have questions:
1. Check your Vehicle Owners Manual for OEM Factory remotes or The User Manual for Dealer Installed or Aftermarket RKE systems.
2. YouTube has many video postings from do-it-yourselfers to assist with all kinds of questions & most customers find if very helpful to WATCH the programming being done which can eliminate mistakes in the sequence.
To locate the programming for your vehicle via this method go to YouTube and once there in the search bar type in the following:
i. If you have a factory RKE system: your make model year + the words program remote (i.e.: 2005 Ford Mustang program remote)
ii. If you have a dealer installed or aftermarket RKE system: the FCC ID or system type + the words program remote (i.e.: ELVAT5C program remote or AS200 program transmitter?)
3. For OEM FACTORY installed systems: send us an eBay message with your vehicles make, model & year = we can pass on to you any programming information requirements we have on hand.
4. For DEALER INSTALLED RKE installed systems: send us an eBay message with your remote controls FCC ID # and PART# and the vehicles make, model, & year = we can pass on to you any programming information requirements we have on hand (the programming for dealer installed RKE systems will be different than Factory or Aftermarket installed RKE systems).
5. For AFTERMARKET INSTALLED RKE installed systems: send us an eBay message with your remote controls FCC ID # and PART# = we can pass on to you any programming information requirements we have on hand (the programming for aftermarket installed RKE systems will be different than Factory or Dealer installed RKE systems).
6. There are also many auto forums that you can go onto by just conducting a google search with your questions.
7. or a local automotive locksmith or your local parts/car/audio store will typically be able to assist you if you are trying to avoid the dealer.