DODGE durango  ram 1500 2500 truck

the manufacturer’s programming instructions For your vehicle make model and year specify diagnostic programming required                               

This keyless entry requires programming by your local dealer or locksmith. The procedure takes a few seconds to complete so many dealers will do it as a courtesy. If your dealer does charge a fee, local locksmiths usually charge much less.

 You will need to visit your local dealer or locksmith to have your remote programmed to your car using diagnostic equipment

 I found this on another site. I hope it helps!

Subject: KEYLESS Entry Programming 

If this will help the folks with 97-98 keyless entry systems, I would love to resolve this issue. 

 installed MOPAR EVS-II & Keyless Entry alarm system . There are several features which can be activated/deactivated according to the owner's preferences: 

1. automatic arming (factory setting: enabled) 
2. arm/disarm chirps (factory setting: enabled) 
3. door unlock when ignition key is turned off (factory: disabled) 

As detailed in the manufacturer's installation instructions, items 1) and 2) above are changed by disconnecting power from the control module, opening up the case, and cutting the "programming loops" or wires in the circuit board for each feature - not so easy to restore. 

The third item can user-programmed at any time as follows: 

1. Enter the vehicle, shut all doors and wait for the dome light to go out. 

2. Complete the next three actions within 5 seconds: 
a. Turn the ignition key to the "ON" position 
b. Turn the dome light "ON" and "OFF" three times 
c. Turn ignition "OFF" 

3. Press the "VALET" button on the dash monitor to toggle the feature on or off. The green LED indicates the status of the feature- 
ON - ignition unlock feature enabled 
OFF - ignition unlock feature disabled 

4. Turn the ignition key "ON" to store the setting and exit the programming mode. 

If the systems are at all alike, the "programming" of the keyless entry system items 1) and 2) sounds simple enough for even a dealership to do! Maybe someone reading this can determine how exactly to do it for a factory installed 97-98 keyless entry system.

DODGE GRAND CARAVAN.PROGRAMMING INSTRUCTIONS

1994-1999 DODGE Caravan

1994-1999 DODGE Grand Caravan

 A max of 2 remotes can be programmed. Any existing remotes not use during programming will become inoperative.

 1994 – 1995

 1.        Access remote transmitter programming terminal behind the glove box LH side.  .

2.        Please note that the remote transmitter programming terminal may be taped to the wiring harness.

3.        Turn ignition ON.

4.        Jump REMOTE transmitter programming terminal and ground.

5.        Ensure doors lick and unlock, indicating you are in programming mode.

6.        PUSH any button for of each remote to be programmed.

7.        Ensure doors lock and unlock after each remote operation, programming complete.

8.        Remove jump lead to exit program.

9.         You can also program replacement remotes with diagnostic equipment (see local Dodge dealer).

 1996 – 1999,a maximum of 4 remotes can be programmed at one time

 NOTE~ 1 programmed remote transmitter must be available for the following to work…IF…you DO NOT have one available you will have to have your remote programmed by your local dealer of locksmith using diagnostic equipment…call first to see if they will do it as a courtesy

 NOTE ~ any existing remote transmitters not used during programming will become inoperative

 10.     Turn ignition ON.

11.     Using programmed remote …Press & hold remote’s UNLOCK button for 4 seconds, now continuing holding UNLOCK button and depress PANIC button at the same time for 6 seconds, release both buttons at this time.

12.     Ensure acoustic signal can be heard, indicating you are in programming mode.

13.     Within 30 Seconds push any button on EACH remote to be programmed

14.     Ensure acoustic signal can be heard after each remote operation

15.     Turn ignition OFF or wait 30 seconds to exit programming mode

16.     Ensure final acoustic signal can be heard

17.   You can also program replacement remotes with diagnostic equipment (see local Dodge dealer).

DODGE CARAVAN

PROGRAMMING INSTRUCTIONS

1994-1999 DODGE Caravan

1994-1999 DODGE Grand Caravan

 A max of 2 remotes can be programmed. Any existing remotes not use during programming will become inoperative.

1994 – 1995

 18.     Access remote transmitter programming terminal behind the glove box LH side.  .

19.     Please note that the remote transmitter programming terminal may be taped to the wiring harness.

20.     Turn ignition ON.

21.     Jump REMOTE transmitter programming terminal and ground.

22.     Ensure doors lick and unlock, indicating you are in programming mode.

23.     PUSH any button for of each remote to be programmed.

24.     Ensure doors lock and unlock after each remote operation, programming complete.

25.     Remove jump lead to exit program.

26.      You can also program replacement remotes with diagnostic equipment (see local Dodge dealer).

 1996 – 1999

a maximum of 4 remotes can be programmed at one time

 NOTE~ 1 programmed remote transmitter must be available for the following to work…IF…you DO NOT have one available you will have to have your remote programmed by your local dealer of locksmith using diagnostic equipment…call first to see if they will do it as a courtesy

 NOTE ~ any existing remote transmitters not used during programming will become inoperative

 27.     Turn ignition ON.

28.     Using programmed remote …Press & hold remote’s UNLOCK button for 4 seconds, now continuing holding UNLOCK button and depress PANIC button at the same time for 6 seconds, release both buttons at this time.

29.     Ensure acoustic signal can be heard, indicating you are in programming mode.

30.     Within 30 Seconds push any button on EACH remote to be programmed

31.     Ensure acoustic signal can be heard after each remote operation

32.     Turn ignition OFF or wait 30 seconds to exit programming mode

33.     Ensure final acoustic signal can be heard

 You can also program replacement remotes with diagnostic equipment (see local Dodge dealer).

PLYMOUTH VOYAGER

PROGRAMMING INSTRUCTIONS

 95 PLYMOUTH ACCLAIM

97-99 PLYMOUTH PROWLER

94-99 PLYMOUTH VOYAGER

 1994-1995

 - ACCESS REMOTE TRANSMITTER PROGRAMMING TERMINAL BEHIND GLOVE BOX LH SIDE

NOTE: THE REMOTE PROGRAMMING TERMINAL MAY BE TAPED ON THE WIRING HARNESS

-          TURN IGNITION TO ON

-          JUMP REMOTE PROGRAMMING TERMINAL AND GROUND

-          DOORS SHOULD LOCK & UNLOCK INDICATING PROGRAMMING ACTIVATION MODE

-          PUSH ANY BUTTON OF EACH REMOTE TO BE PROGRAMMED

-          DOORS SHOULD LOCK AND UNLOCK AGER EACH REMOTE OPERATION, INDICATING PROGRAMMING COMPLETE

-          MAX 2 REMOTES CAN BE PROGRAMMED - ANY EXISITNG REMOTES NOT USED DURING PROGRAMMING WILL BE INOPERATIVE

  1996 -1999

 -          ONE PROGRAMMED REMTOE MUST BE AVAILABLE FOR THE FOLLOWING PROCEDURE TO OPERATE – if no remote available you must program it using diagnostic equipment. This means, you will have to locate your local dealer and have them program the remote once you receive it. Normally, there is no charge for this service as it only takes about 3 minutes from start to finish; HOWEVER, some of our customers have reported that their local dealers do charge. So, you may want to checkPRIOR to purchase so you do not have any surprises. In the realm of keyless entries, however, by purchasing a keyless from sources like eBay, you are saving a bundle either waycompared to ordering a keyless entry from a dealer or even other online sources.

-          OBTAIN ALL REMOTES

 -          NOTE: ANY EXISITING REMOTES NOT USED DURING PROGRAMMING WILL BE INOPERATIVE

 -          TURN IGNITION TO ON

 -          USING THE PROGRAMMED REMOTE PROCEED…

 -          …PUSH AND HOLD REMOTE UNLOCK BUTOTN FOR 10 SECONDS

 -          …AFTER HOLDING UNLOCK BUTTON FOR 4 SECONDS, PUSH REMOTE PANIC BUTTON AND RELEASE BOTH BUTTONS’

 -          ENSURE ACOUSTIC SIGNAL CAN BE HEARD – PROGRAM MODE ACTIVATED

 -          you must press the lock and unlock button simultaneously

-           let go of both and press and release any button and listen for the chime

 -          W/I 30 SECS. PUSH ANY BUTTON OF EACH REMOTE TO BE PROGRAMMED

 -          ENSURE ACOUSTIC SIGNAL CAN BE HEARD AFTER EACH REMOTE OPERATION

 -          TURN IGNITION TO OFF OR WAIT 30 SECONDS TO EXIT PROGRAMMING MODE

 -          ENSURE FINAL ACOUSTIC SIGNAL IS EMITTED

 -          REPLACEMENT REMOTES CAN ALSO BE PROGRAMMED AT YOUR LOCAL DEALER USING DIAGNOSTIC EQUIPMENT

 -          4 REMOTES PROGRAMMED AT ONCE

CHRYSLER

TOWN & (AND) COUNTRY

PROGRAMMING:

CHRYSLER TOWN & COUNTRY

1996-1999                                                     

++++Maximum 4 remotes programmed at one time- any existing remotes not used during programming will become inactive.

1.        Please note: you must have one programmed remote to make the following procedure work…REPLACEMENT remotes can also be programmed using diagnostic equipment at your local dealer…please call first and ask if they will do it as a courtesy (takes 3 minutes) .

2.        turn ignition to ON

3.        Using a programmed remote…

4.        …push and hold remote UNLOCK button……after holding the unlock button for 4 seconds, push remote PANIC button and release both buttons at the same time for a total of about 10 seconds.

5.        …Listen for acoustic signal – programming mode active

6.        …within 30 seconds press any button of each remote to be programmed

7.        …ensure acoustic signal sounds after each remote operation

8.        …turn ignition to OFF or wait 30 seconds to EXIT programming

9.        …ensure final acoustic sound is heard

10.     REPLACEMENT remotes can also be programmed using diagnostic equipment at your local dealer…please call first and ask if they will do it as a courtesy (takes 3 minutes) .