SunFire V120 Server, 650MHz CPU, 1.5 GB RAM, DVD-ROM, NO HDD, Powers On.

The server powers on and I was able to communicate with it over the LOM port. I'm not able to test any further due to not having a hard drive. I can't guarantee it is fully functional, so I'm selling it AS-IS, For parts or not working.

There are some heavy scuffs and scratches on the exterior.

Here is what I was able to get using LOM:

LOMlite starting up.

CPU type: H8/3437S, mode 3
Ram-test: 2048 bytes OK
Initialising i2c bus: OK
Searching for EEPROMs: 50(cfg)
I2c eeprom @50: OK
i2c bus speed code 01... OK
Probing for lm80s: 28
Initialising lm80 @28: OK
Probing for lm75s: none
System functions: PSUs fans breakers rails gpio temps host CLI ebus clock

LOMlite console
lom>
LOM event: +0h0m0s LOM booted

lom>environment
Fault  OFF
Alarm1 OFF
Alarm2 OFF
Alarm3 ON

Fans:
1 fan1 OK standby
2 fan2 OK standby
3 cpu OK standby
4 psu OK standby

PSUs:
1 OK standby

Temperature sensors:
1 Enclosure 24degC OK

Overheat sensors:
1 CPU standby

Circuit breakers:
1 SCSI-Term standby
2 USB0 standby
3 USB1 standby
4 SCC standby

Supply rails:
1 5V standby
2 3V3 standby
3 +12V standby
4 CPU core standby
5 +3VSB standby


lom>poweron
lom>
LOM event: +0h12m34s host power on
▒Done
Bootmode is 0
[New I2C DIMM address]
MCR0 = 57b2ce06
MCR1 = 80008000
MCR2 = c7700fff
MCR3 = a00001ef
Ecache Size = 512 KB
NVRAM Test
Icache Test
Dcache Test
MMU Test
FPU Test
Ecache Tag Addr Test
Ecache RAM Addr Test
Clearing E$ Tags Done
Clearing I/D TLBs Done
Probing memory
Done
MEMBASE=0x80000000
MEMSIZE=0x20000000
Data Line Test
Core Memory Test
Clearing memory...including Unix retained memory...Done
Turning ON MMUs Done
Copy ROM to RAM (170080 bytes) Done
Orig PC=0x1fff0007e44  New PC=0xf0f07e9c
Processor Speed=648MHz
Memory Data Line Test
Memory Addr Line w/ Ecache Test
ECC Block Memory Test
Looking for Dropin cPOST ... found
Copying Client...Done
Transferring control to Client...

Sun Microsystems, Inc.     cPOST
@(#) cpost 1.0.17 2003/10/06 17:10

All Basic UltraSPARC IIe PBM Tests
        Init CPU PBM
        PIO Decoder And BCT Test
        CPU IOMMU Reg Test
        CPU IOMMU RAM NTA Test
        CPU IOMMU CAM NTA Test
        CPU IOMMU RAM Address Test
        CPU IOMMU CAM Address Test
        IOMMU TLB Compare Test
        IOMMU TLB Flush Test
        PBM Control/Status Reg Test
        PBM Diag Reg Test
        CPU PBM Reg Test

All Basic APB Simba Tests

Init PCI

All Basic RIO Tests (RIO# 1)
        RIO Ebus Config Space Reg Test
        RIO Network Config Space Reg Test
        RIO Firewire Config Space Reg Test
        RIO USB Config Space Reg Test
All Basic RIO Tests (RIO# 2)
        RIO Ebus Config Space Reg Test
        RIO Network Config Space Reg Test
        RIO Firewire Config Space Reg Test
        RIO USB Config Space Reg Test
All Basic SCSI Controller Tests
        Symbios SCSI Controller PCI Config Space Test
All Basic SCSI Controller Tests
        Symbios SCSI Controller PCI Config Space Test
Basic SouthBridge Tests
        Southbridge ISA Config Space Reg Test
        Southbridge PMU Config Space Reg Test
        Southbridge IDE Config Space Reg Test
        Southbridge Audio Config Space Reg Test
All Memory Stress Tests
        Consist Write Data Test
Resetting...
▒
Processor Speed = 648 MHz
Baud rate is 9600
8 Data bits, 1 stop bits, no parity (configured from lom)

Firmware CORE  Sun Microsystems, Inc.
@(#) core 1.0.17 2003/10/06 17:09
Software Power ON
Verifying NVRAM...Done
Bootmode is 0
[New I2C DIMM address]
MCR0 = 57b2ce06
MCR1 = 80008000
MCR2 = c7700fff
MCR3 = a00001ef
Ecache Size = 512 KB
Clearing E$ Tags Done
Clearing I/D TLBs Done
Probing memory
Done
MEMBASE=0x80000000
MEMSIZE=0x20000000
Clearing memory...Done
Turning ON MMUs Done
Copy ROM to RAM (170080 bytes) Done
Orig PC=0x1fff0007e44  New PC=0xf0f07e9c
Processor Speed=648MHz
Looking for Dropin FVM ... found
Decompressing Client Done
Transferring control to Client...

ttya initialized
Reset Control: BXIR:0 BPOR:0 SXIR:0 SPOR:1 POR:0
Probing upa at 1f,0 pci pci pci
Probing upa at 0,0 SUNW,UltraSPARC-IIe SUNW,UltraSPARC-IIe (512 Kb)
Loading Support Packages: kbd-translator
Loading onboard drivers: ebus flashprom eeprom
Starting real time clock...
idprom SUNW,lomh
Probing /pci@1,1 Device 3  pmu i2c temperature dimm dimm dimm i2c-nvram
   idprom motherboard-fru fan-control
lomp
Sun Fire V120 (UltraSPARC-IIe 648MHz), No Keyboard
OpenBoot 4.0, 1536 MB memory installed, Serial #56375633.
Ethernet address 0:3:ba:5c:39:51, Host ID: 835c3951.



Drive not ready
Can't read disk label.
Can't open disk label package
Boot device: /pci@1f,0/pci@1/scsi@8/disk@1,0:a  File and args:
Drive not ready
Can't read disk label.
Can't open disk label package
Evaluating: boot

Can't open boot device