Brand NEW READY TO PROGRAM BATTERY INSTALLED

What are you purchasing?

This is ONE (1) NEW REPLACEMENT REMOTE FOR Factory OEM (Original Equipment Manufacturer) keyless entry remote, aka "key fob" that will work with your OEM Factory installed RKE system.

Compatibility: Works with vehicles that use a factory keyless entry system listed in our compatibility section above AND below.

FCC ID#(s)

for GQ43VT14T

Alternate Spellings

for GQ4-3VT14T, GQ4 3VT14T, GQ43VT14T, GQ43VTI4T, GO43VT14T, G043VT14T

Part #(s)

for TRW 88LPOO65 RSS-210 CAN: 1470 102 849 DENSO MEX: RCPTR3002-028

Dealer #(s)

for 88969657

Button Count

4; Lock, Unlock, Hatch (Glass), Panic ALARM HORN OPENER DOOR REAR LIFT

Battery (installed)

1; CR2032

Frequency

315 MHz (MHz)

LED Light Color

for Toyota Matrix 2003 2004 2005 2006 2007 2008

for Pontiac Vibe 2003 2004 2005 2006 2007 2008 STD / XR / XRS

Programming:

Please note not all customers will be able to complete the programming on their own so if you are having trouble or unsure diagnostic programming is available at your local qualified automotive locksmith or car/audio shop.

Programming Procedure #265

  1. Start with the following conditions:
    1. Key is out of the ignition
    2. Driver door is open (all other doors are closed)
    3. Driver door is unlocked (other doors don’t matter).
  2. Perform the next two steps within 5 seconds:
    1. Insert the key into the ignition (don’t turn it) and pull it out.
    2. Insert the key into the ignition (don’t turn it) and pull it out.
  3. Perform these steps within 40 seconds:
    1. Close then open the driver’s door.
    2. Close then open the driver’s door.
    3. Insert the key into the ignition (don’t turn it) and pull it out.
  4. Perform these steps within 40 seconds:
    1. Close then open the driver’s door.
    2. Close then open the driver’s door.
    3. Close the driver’s door.
    4. Insert the key into the ignition.
    5. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
    6. Remove the key from the ignition.
  5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.
  6. Perform these steps within 40 seconds:
    1. Press the lock and unlock buttons on the transmitter simultaneously for 1 second and release.
    2. Immediately after releasing the lock and unlock buttons, press the lock button by itself and hold it for 2 seconds. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b for this remote as it has not been accepted.
    3. Within 40 seconds, repeat steps 6a and 6b for each additional transmitter.
  7. Open driver’s door.

 Most remotes have very simple do-it-yourself programming instructions. You do not need to be a mechanic to program the remote to your car - takes 5 minutes! Some make, models, & years require diagnostic programming available at your local dealer or locksmith.

IF...your make, model, & year requires diagnostic programming instructions or if you find the programming instructions to complicated THEN...you will need to have your auto key remote programmed to your vehicle at a local dealer or locksmith.

Condition Notes

 Pre-Owned ready to program to your compatible vehicle RKE system.

Additional Information

Your car may have the optional, Toyota VIP or RS3200 RKE system installed. (NOTE: this remote will
not work for the RS32000 or RS3000 VIP systems - they are dealer installed).

This remote will ONLY work with the FACTORY INSTALLED RKE System.


Installed RKE System Type:

Please be sure you have a FACTORY (RKE) remote keyless entry system. It was not standard on all vehicles. If your current remote looks the same then this will work. Other options include: Dealer Installed or Aftermarket. The system installed in your vehicle will CHANGE the required remote. If you are unsure ask your local dealer they will need your VIN # (Vehicle Identification Number (located on our vehicle registration car, on your driver side door jam, or your windshield (lower left drives side))).

Why does your vehicles installed RKE / Security system determine which remote control your can purchase?

The remotes job is to pair with your vehicles installed RKE system. It will only sync to a matching system; therefore, you cannot purchase a different type of remote than the remote manufactured with the system. It will not pair with a foreign system.

Programming:

We will send you information on how to locate programming requirement/instructions for your make, model, and year vehicle. Some vehicles have DIY (do-it-yourself) programming instructions available. While other vehicles require diagnostic programming which is available at your local qualified automotive locksmith or dealer.

Programming Requirement Information NOTE:

The vehicle manufacturers determine the programming requirements at the time of manufacture. We pass the programming requirements / instructions on to you as a courtesy. We do not write the programming nor do we determine which vehicles require diagnostic programming and which vehicles can be programmed by the you (DIY). We are not locksmiths nor mechanics nor are we familiar with EVERY vehicles program sequence. If you have questions:

        1. Check your Vehicle Owners Manual for OEM Factory remotes or The User Manual for Dealer Installed or Aftermarket RKE systems.

 2. YouTube has many video postings from do-it-yourselfers to assist with all kinds of questions & most customers find if very helpful to WATCH the programming being done which can eliminate mistakes in the sequence.

To locate the programming for your vehicle via this method go to YouTube and once there in the search bar type in the following:

i.      If you have a factory RKE system: your make model year + the words program remote (i.e.: 2005 Ford Mustang program remote)

ii.      If you have a dealer installed or aftermarket RKE system: the FCC ID or system type + the words program remote (i.e.: ELVAT5C program remote or AS200 program transmitter?)

 3. For OEM FACTORY installed systems: send us an eBay message with your vehicles make, model & year = we can pass on to you any programming information requirements we have on hand.

      

 4. For DEALER INSTALLED RKE installed systems: send us an eBay message with your remote controls FCC ID # and PART# and the vehicles make, model, & year = we can pass on to you any programming information requirements we have on hand (the programming for dealer installed RKE systems will be different than Factory or Aftermarket installed RKE systems).

     

 5. For AFTERMARKET INSTALLED RKE installed systems: send us an eBay message with your remote controls FCC ID # and PART# = we can pass on to you any programming information requirements we have on hand (the programming for aftermarket installed RKE systems will be different than Factory or Dealer installed RKE systems).

      

6. There are also many auto forums that you can go onto by just conducting a google search with your questions.

       

7.  or a local automotive locksmith or your local parts/car/audio store will typically be able to assist you if you are trying to avoid the dealer.