Oven Bake Element for Whirlpool RJE333PP1 RJE363PP2 RM280PXBQ2 RF363PXPT1



Product Description

308180
308180
308180
308180
308180
308180
  • βœ”βœ”γ€π˜½π˜Όπ™†π™€ π™€π™‡π™€π™ˆπ™€π™‰π™ π™’π™ƒπ™„π™π™‡π™‹π™Šπ™Šπ™‡ π™Šπ™‘π™€π™‰γ€‘308180 WP308180 oven bake element is at the bottom of the oven and supplies the heat for baking.This bake element wp308180 is for ranges.The rated power is 2600 watts and the rated voltage is 240 volts.β–ΊThe size is approximately 16-5/8’’wide X 15-3/4"deep.β–ΊThe mounting bracket is 2" wide from the mounting bracket to the terminal end is 3". Mounting holes measure 1-3/4" apart center to center.β–Ίpackage includes 1 x oven heating element wp308180
  • βœ”βœ”γ€π™‰π™„π˜Ύπ™†π™€π™‡ π™Žπ™π˜Όπ™„π™‰π™‡π™€π™Žπ™Ž π˜Όπ™‡π™‡π™Šπ™”γ€‘whirlpool oven element replacement 308180 oven bake element is made of HIGH TEMPERATURE RESISTANT NICKEL STAINLESS STEEL ALLOY, well-tested by manufacturer, and the product has a long service life. The terminals are nickel-plated,push-in type. β–ΊIf the following problems occur, then you can replace the 308180 Range Bake Element:β‘ If your oven heating element brokeβ‘‘heats up inconsistentlyβ‘’bottom oven heating element not working
  • βœ”βœ”γ€π˜Ύπ™Šπ™ˆπ™‹π˜Όπ™π™„π˜½π™‡π™€ π™ˆπ™Šπ˜Ώπ™€π™‡γ€‘308180 Oven Bake Element is a standard heating element which fits most ovens that fits for Estate,Kenmore,Kitchen-Aid, Whirlpool,Roper Rangeβ–ΊReplaces 308180, 311470, 313827, 660576, 661170, 14210047, 308180BULK, 99989645, AP6007578, PS11740695, EAP11740695, rf3165xvw0, rf395pxxn0, rf395pxxn1, rf395pxxn2, rf363pxdn0, rf363pxdw0, rf363pxpt0, fep310bl0, fep310bl1, fep310bw0, fep310bw1, fep310yw0, fep310yw1, fep310yw2, fep314bl0, fep314bw0, fep320bl0, fes350bl0,etc
  • βœ”βœ”γ€π˜½π™π™„π™‰π™‚ π˜Ύπ™Šπ™‰π™‘π™€π™‰π™„π™€π™‰π˜Ύπ™€ π™π™Š π™”π™Šπ™π™ 𝙇𝙄𝙁𝙀】Unplug the range or shut off the house circuit breaker for the range before installing WP308180 Oven Bake Element. Wear work gloves to protect your hands. You should prepare a phillips screwdriver and pair of work gloves.Unscrewed the two screws that held the element in place,needed pliers to remove the sta-kon connectors from old element. Attached them to new element and put screws back in place