
Connect a PC to a JAMMA cabinet in seconds!
New Version!
The J-PAC (JAMMA interface for Pc to Arcade Controls) is a board which allows plug-in connection of a JAMMA arcade cabinet to a VGA card and keyboard port or USB port on a PC motherboard. It incorporates all the advanced features of the I-PAC with an on-board JAMMA connector
NEW VERSION! Now has inputs fully protected against static discharge and reverse connection, now supports 3 extra JAMMA connections (Tilt, Service SW and Test)
Now supports 12 volt coin doors.
Fully programmable key code set. Stored even after power off.
Dual interface USB or Keyboard.
Supports I-PAC optional pre-assembled LED harness with 3 panel mounting LEDs which emulate the keyboard Lights.
Lead plugs into keyboard socket on PC or USB port.
Self-Test LED gives an instant check of all your wiring. Can indicate which, if any, input has a problem.
No separate power needed.
Does not use a matrix - no ghost keys. All inputs are completely separate and generate their own interrupt - this is the fastest possible method.
Does not use a scanning method which causes a variable delay.
Either uses standard MAME keys or you can program your own character set.
Shift functions. Holding 'Start1' and pressing other buttons sends a range of codes for MAME functions such as 'escape', 'Coin 1', 'tab', 'enter'. This means no extra buttons are needed on the cabinet. In programmable mode any input can be the shift key and all keys can be programmed with a shifted code.
Connector for ordinary keyboard which can be used together with the controls if required.
No special drivers needed. USB drivers are generic Windows.
All control inputs which are part of a normal JAMMA standard are routed to an on-board JAMMA edge connector.
Connector for VGA input from PC VGA card. Routes through to JAMMA edge connector for connection to the cabinet arcade monitor.
On-board video amplifier boosts signal to standard arcade monitor levels. Uses high-bandwidth video amplifier chip.
Custom microcontroller only allows sync signals to be sent to the monitor if they are in the correct range that the monitor is designed for. Avoids driving the monitor with a too-high horizontal sync rate which can damage some arcade monitors.
Sync circuitry also converts separate horizontal and vertical syncs into composite sync. Can handle both positive and negative vertical sync.
If required, can divide a 31Khz VGA signal in half so that it will display a stable picture on a 15Khz arcade monitor. Useful for checking boot-up progress and configuration (not for application use). Automatically stops dividing the signal when it detects a correct 15Khz rate is being send by the PC.
JAMMA cabinet speaker routed to screw connectors for wiring to powered sound card or hacked PC speakers.
Legal Note.
For legal reasons we must state here that the J-PAC is not designed to be used in revenue-earning applications where a credit mechanism is used. The J-PAC contains no specific interface functionality for any credit device. Although it has inputs which connect to the JAMMA coin signals, these are designed such that activating a switch connected to them causes the MAME 'coin' keycodes (5 or 6) to be sent. These are designed to be used with panel pushbuttons not coin doors or note acceptors.
Return Shipping Address
Holland Computers, Inc.
483 N. Abbe Rd.
Elyria, Ohio 44035
With respect to parts, materials and equipment, the manufacturer's warranty, if any; or with respect to used or re-manufactured parties, materials and equipment, thirty (30) days after sale and this agreement specifically excludes and disclaims all warranties, express or implied concerning merchantability or fitness for any particular use or purpose. All parts, materials and/or equipment are sold “as is.” Holland will make reasonable efforts to assist customer with regard to all warranties, if any, provided for customer benefit by the original supplier or manufacturer with respect to parts, materials and/or equipment sold pursuant to this order. All system and component warranties do not include or cover any system or network Virus damage, infection from viruses or system or network software conflicts. Holland Computers, Inc. is not responsible for any system or server data recovery needed due to hardware failure and/or software problems. Customers sole and exclusive remedy in connection with any claim, arbitration, lawsuit or other cause of action whatsoever directly or indirectly relating to or arising out of the agreement, or any services rendered by Holland Computers in connection there-with, whether based on warranty, contact, tort of other legal theory shall be repair of replacement of the defective part, material and or damages of any type. Any lawsuit or arbitration based on or related to this agreement or the parts, materials, equipment and labor sold or rendered by Holland Computers must be commenced within thirty(30) days after delivery to the customer of the goods or equipment or such lawsuit shall be forever barred. Customer shall not be entitled to either remedy unless Holland Computers has received written notice of the customers claim within thirty (30) days after the delivery of the equipment or other goods or service to the customer.
Customer agrees that any dispute or claim arising out of this Agreement shall be enforced by lawsuit in Lorain County Ohio, Ohio only and is limited to the amount billed for the Goods and or Services. Customer shall indemnify and hold Holland harmless from all expenses (including reasonable attorneys' fees), claims, demands, suits, judgments, actions, costs and liabilities (including those alleging negligence on the part of Holland) which arise from, relate to or are connected with the Customer's negligent possession, use, operation and/or resale of the parts, materials and/or equipment described herein.