Why purchase a NEW replacement keyless entry remote transmitter?

The vehicle keyless entry remote key fob you are going to purchase from us is BRAND NEW. We seek out ONLY quality replacement remote manufacturers to ensure the key fob we sell to you is of the highest quality. Here at KeylessRemoteWarehouse we test to ensure that the shells or outer housing are made to resist cracks and breaks upon being dropped. Let?s face it; we all are going to drop our key set from time to time. We ensure that the keyless entries button pads are going to last; buying a new replacement remote control from us puts you at a longevity advantage over purchasing a used part that already has considerable wear. Even the circuit boards we choose are high quality clones with new solder joints and new resistors to ensure that they will last for the long haul. We guarantee our products are delivered to you in a ready-to-program state. We offer these car clickers at a significant cost savings to stealerships so you can keep your hard earned cash for something more fun J. Why wait? Add some convenience to your daily routine and help save the environment, order your NEW replacement car remote control today!

What are you purchasing?

This is ONE (1) NEW replacement keyless entry remote, aka "key fob" that will work with your compatible OEM (Original Equipment Manufacturer) Dealer installed RKE system once successfully programmed to your vehicle.

Compatibility: Works with vehicles that use a factory keyless entry system listed in our compatibility section above AND below.

Brand New Aftermarket Replacement For:

Compatible with the following:

Compatible With:

Make Model Year
Scion xA 2004-2006
Scion xB 2004-2006
Toyota 4Runner 2000-2002
Toyota Avalon 1995-2001
Toyota Camry 2000-2004
Toyota Celica 2000-2005
Toyota Corolla 1998-2004
Toyota Echo 2000-2004
Toyota Highlander 2001-2004
Toyota Land Cruiser 1998-2004
Toyota Matrix 2003-2004
Toyota MR2 2000-2004
Toyota Prius 2001-2004
Toyota RAV4 1996-2005
Toyota Sequoia 2001-2004
Toyota Sienna 1998-2004
Toyota Solara 1999-2004
Toyota Tacoma 1995-2004
Toyota Tundra 2003-2006

FCC ID#(s)

BAB237131-056

Alternate Spellings

BAB-237131-056, BAB 237131056, BAB237131-056, BAB237131-O56, BAB237I3I-056, BAB237131-0S6

DEALER INSTALLED SYSTEM

Dealer-Installed VIP or RS3200 Security System ONLY

Part #(s)

PT398-07101

Dealer #(s)

08191-00922

Button Count

3; Lock, Unlock, Panic

Battery (installed)

1; CR2025

Frequency

304 MHz (MHz)

LED Light Color

None

Programming:

Please note not all customers will be able to complete the programming on their own so if you are having trouble or unsure diagnostic programming is available at your local qualified automotive locksmith or car/audio shop.

TOYOTA TVIP SYSTEM PROGRAMMING-RS3200

ADD ADDITIONAL REMOTE CONTROL(S) TO SYSTEM
Follow this procedure to add additional remote controls to a system. The RS3200 may be programmed to operate with a maximum of four remote controls. When a new remote controls is programmed, it will work in the default operation mode (press the UNLOCK button twice to unlock all doors and no AUX button function on 4 button remote controls); to change the operation mode, you must perform the separate REMOTE CONTROL FUNCTION SELECT procedure as shown on pages 6 and 7 OF THE manual. 

1. Before you begin:
Open the driver s door and remove the key from the ignition switch.
2. Start the programming procedure. (Complete these steps within 40 seconds.)

a. Insert the key into, and remove it from the ignition switch 2 times.

b. Close, then open the driver s door 2 times.

c. Insert the key into, and remove it from the ignition switch 1 time.


d. Close, then open the driver s door 2 times.

e. Insert the key into, the ignition switch and leave it in.
f. Close the driver s door.
g. Turn the key from LOCK to ON, then back to LOCK.
h. Remove the key from the ignition switch.

i. The tail and marker lights flash 1 time, the buzzer chirps 1 time and the doors lock
and unlock 1 time.*

* If the system does not activate the lights, buzzer and door locks 1 time, start over.

3. Program (add) an additional remote control.

a. Press and release both the LOCK and UNLOCK buttons control at the same
time.
b. Press and release the LOCK button.
c. The tail and marker lights flash 1 time, the buzzer chirps 1 time, and the doors lock
and unlock 1 time.*
Note: Repeat the above steps to add additional remote controls.

4. Complete the programming steps.

a. Open the driver s door

REPROGRAM EXISTING REMOTE CONTROLS
Follow this procedure to clear all existing remote control codes and reprogram existing remote controls to
a system. When existing remote controls are reprogrammed, they will work in the default operation mode (press the UNLOCK button twice to unlock all doors and no AUX button function on 4 button remote controls); to change the operation mode, you must perform the separate REMOTE CONTROL FUNCTION SELECT procedure as shown on pages 6 and 7.

1. Before you begin: Open the driver s door an

2. Start the programming procedure. (Complete these steps within 40 seconds.)
a. Insert the key into, and remove it from the ignition switch 2
times.
b. Close, then open the driver s door 2 times.
c. Insert the key into, and remove it from the ignition switch 1 time.
d. Close, then open the driver s door 2 times.
e. Insert the key into, the ignition switch and leave it in.
f. Close the driver sdoor.
g. Turn the key from LOCK to ON 2 times (ending at LOCK).
h. Remove the key from the ignition switch.
i. The tail and marker lights flash 2 times, the buzzer chirps 2 times and the doors
lock and unlock 2 times.*

*If the system does not activate the lights, buzzer and door locks 2 times, start over.

3. Reprogram an existing remote control.

a. Press and release both the LOCK and UNLOCK buttons on one remote
control at the same time.
b. Press and release the LOCK button.
c. The tail and marker lights flash 1 time, the buzzer chirps 1 time, and the doors lock
and unlock 1 time.*
Note: Repeat the above steps to program (add) additional remote controls.

4. Complete the programming steps.
a. Open the driver s door

Condition Notes

New aftermarket replacement -ready to program to your compatible vehicle RKE system.

Installed RKE System Type:

Please be sure you have a DEALER (RKE) remote keyless entry system. It was not standard on all vehicles. If your current remote looks the same then this will work. Other options include: Dealer Installed or Aftermarket. The system installed in your vehicle will CHANGE the required remote. If you are unsure ask your local dealer they will need your VIN # (Vehicle Identification Number (located on our vehicle registration car, on your driver side door jam, or your windshield (lower left drives side))).

Why does your vehicles installed RKE / Security system determine which remote control your can purchase?

The remotes job is to pair with your vehicles installed RKE system. It will only sync to a matching system; therefore, you cannot purchase a different type of remote than the remote manufactured with the system. It will not pair with a foreign system.

Programming:

We will send you information on how to locate programming requirement/instructions for your make, model, and year vehicle. Some vehicles have DIY (do-it-yourself) programming instructions available. While other vehicles require diagnostic programming which is available at your local qualified automotive locksmith or dealer.

Programming Requirement Information NOTE:

The vehicle manufacturers determine the programming requirements at the time of manufacture. We pass the programming requirements / instructions on to you as a courtesy. We do not write the programming nor do we determine which vehicles require diagnostic programming and which vehicles can be programmed by the you (DIY). We are not locksmiths nor mechanics nor are we familiar with EVERY vehicles program sequence. If you have questions:

        1. Check your Vehicle Owners Manual for OEM Factory remotes or The User Manual for Dealer Installed or Aftermarket RKE systems.

 2. YouTube has many video postings from do-it-yourselfers to assist with all kinds of questions & most customers find if very helpful to WATCH the programming being done which can eliminate mistakes in the sequence.

To locate the programming for your vehicle via this method go to YouTube and once there in the search bar type in the following:

i.      If you have a factory RKE system: your make model year + the words program remote (i.e.: 2005 Ford Mustang program remote)

ii.      If you have a dealer installed or aftermarket RKE system: the FCC ID or system type + the words program remote (i.e.: ELVAT5C program remote or AS200 program transmitter?)

 3. For OEM FACTORY installed systems: send us an eBay message with your vehicles make, model & year = we can pass on to you any programming information requirements we have on hand.

      

 4. For DEALER INSTALLED RKE installed systems: send us an eBay message with your remote controls FCC ID # and PART# and the vehicles make, model, & year = we can pass on to you any programming information requirements we have on hand (the programming for dealer installed RKE systems will be different than Factory or Aftermarket installed RKE systems).

     

 5. For AFTERMARKET INSTALLED RKE installed systems: send us an eBay message with your remote controls FCC ID # and PART# = we can pass on to you any programming information requirements we have on hand (the programming for aftermarket installed RKE systems will be different than Factory or Dealer installed RKE systems).

      

6. There are also many auto forums that you can go onto by just conducting a google search with your questions.

       

7.  or a local automotive locksmith or your local parts/car/audio store will typically be able to assist you if you are trying to avoid the dealer.