WHATSMINER 8" x 8" ASIC Fan Silencing Kit for the M32s, M32, M31s, M30s++, M30s, M21s & M20s model ASICS (With 140mm fans!)

It does NOT fit: M31, M21 or M20 (120mm fans)... You can use the Standard 6" kit for those below.

It does NOT fit: M50's

Listing: Fan Hose Adapter 6 In x 6 Out Kit for Crypto Miners ASIC

Listing: Fan Hose Adapter 6 In x 4 Out Kit for Crypto Miners ASIC

Note:  This is a complete kit.... Everything you will need Except the Blower/Fan. 


Honestly, It doesn't make since for me to buy the blower on Amazon, ship it to my office, add it to your kit, pay for the extra shipping back to you, pay eBay 12% in fees, buy a bigger box, etc.... all I was doing was charging you more for all of these fees....when you can have it dropped shipped directly to you.  The fan is obtainable by searching Amazon for “AC Infinity S8”. 

  • What miners do they work with?
They will work the following Whatsminer ASIC's: M30s++, M30s+, M31s+, M21s, M20s, M32's & M32. 

All you do is remove the existing fans, and plug in the two 4 Pin or 6 Pin Fan Spoofers (Included!) on the AISC's control board where the original fans would normally plug in.  You mount the adapters to the existing fan locations where the fan's would normally mount with the screws we provide (Not the ones that mount the old fans!) and clamp the 800 CFM blower (Provided by you!) to the bottom flange (as shown in the photos).

Yes, they can also be mounted vertically on a sheet of plywood (This is the way Fruits & Associates use them).  Mounting them vertically on the wall takes up less space, you don't need a shelving rack, and it's easy to add a 6" standard dryer hose to a vent outside for the exhaust. It's a promise if you add these to your garage wall, your wife will let you buy more!  I do recommend a screen or a filter if there is a lot of dirt or kids fingers......

These blowers are very quiet.. especially if you reduce the speed to 3/4 of maximum speed, which is all you need...  Just watch your temps......and understand,that YOU have to control the blower speed... not the ASIC.   The safest thing to do is just run them full speed.  The good news, is the sound is quite pleasing.... a soft hum vs an annoying screaming sound the original fans make!  But on this side note.... remember, we are doing nothing to quiet the PSU's and in many cases, they are also louder than this blower......but the whole thing will be MUCH quieter than the original fans!!!

    1. One - ABS 8 Inlet adaptor (Connects directly to the S8 Blower and your ASIC)
    2. One - ABS 8" Outlet adaptor (Connects to the Discharge Side of your ASIC and Discharges the hot air to a 8" dryer hose)
    3. Two - Stainless Steel 8" Clamp (To attach the S8 Adaptor to the AC Infinity Blower)
    4. Eight - M4 x 12mm Screws (To mount both adaptors where the original fans mounted)
    5. Two - 4 Pin (2 x 2)  x 6 pin  (Inline) Fan Adaptors & Two 6 Pin Fan Emulators (Plugs in where the original fans did)
    6. Installation Instructions
    7. Free Shipping!!!!!
  • What is NOT included?
    1. The Blower / Fan (It is easily obtainable on Amazon..Just search for AC Infinity S8)
  • Is this better than Immersion Mining Tanks?
So, Fruits & Associates actually have an Immersions system with 10 ASIC's running in BitCool Engineered Fluid.  It works well, and you do get amazing results.... But, you are taking the heat from the ASIC, transferring it to the oil, then taking the oil and transferring the heat (via the cooler) to Air.  It is VERY expensive to obtain, you have to buy the tank, the pump, the oil, the cooler, electricity, etc...  This option takes the heat directly to air..... one step removed.

If you have any additional questions, please don't hesitate to ask... we also have several other models available (s19's, Z15's, L3's, S9's, etc...)

Thanks for shopping at Ben's Creations.
An Authorized Seller for Fruits & Associates products.