Item Description
  • Cup Head Coach Carriage Bolt & Nuts are used to attach wood to wood or steel with a matching nut to clamp the materials together. The coach bolt has a low profile domed head and a square section under the head which resists turning when the nut is tightened or removed. The square section pulls into the wood as the nut on the other end is tightened, thus eliminating the need for a second spanner. Used to support structure, in timber framing, outdoor furniture, fencing and retaining walls, a common example is the seat and back slats of your garden bench and table furniture
  • Material / Coating: Galvanised is a dull greyish colour and can be a little rough in appearance and is mainly used outdoors because of its superior corrosion resistance and proven longevity. Also known as HDG, it is one of the best coatings for protection against rust. Galvanised fasteners have been used across many industries in Australia for over 150 years, roofing, steel buildings, trailers, bridges, fencing, power poles, marina’s, are just a few examples. Recently we have seen a lot of new coatings developed, terms like class 3, class 4, B8, climseal, mechanical galvanised and ruspert are all variations of the original galvanising
  • Grade v Class Difference: Imperial fastenings are referred to as grades, and metric fastenings are referred to as classes. Both have marking systems that make it possible to determine grade and class. An example is a ½” UNC bolt with 5 lines on the head is grade 8 and 3 lines is grade 5, both are regarded as high tensile. Metric bolts are slightly different, if it has 4.6 then it is mild steel and 8.8 is high tensile. The markings on a stainless fastener indicate the grade of material and strength, e.g. material G304 grade will have one of the following markings: A2-70, G304, A2, 304 and G316 grade stainless will have one of the following: A4-70, G316, A4, 316
  • Thread Pitch (Metric): Pitch means the distance between the peaks of two threads along a screw, bolt, or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example, a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm
  • Fastener length: is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. Thus, fasteners with heads that sit above the surface are measured from under the head to the end of the fastener, while fasteners that sit flush with the surface are measured from the top of the head to the end of the fastener
  • Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
  • Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as height, width, visible stamped markings, appearance or actual finish
  • Photos: are of the product but may not be the actual diameter, height, width, length you may require, always refer to the size in the description and additional specifications data provided prior to ordering
  • Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Fastener Kits Online is not responsible for any loss, claim or damages arising therefrom. In developing this information, Fastener Kits Online has made a determined effort to present it accurately
  • Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
  • Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
  • Prices: Include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
  • Cup Head Coach Carriage Bolt & Nuts are used to attach wood to wood or steel with a matching nut to clamp the materials together. The coach bolt has a low profile domed head and a square section under the head which resists turning when the nut is tightened or removed. The square section pulls into the wood as the nut on the other end is tightened, thus eliminating the need for a second spanner. Used to support structure, in timber framing, outdoor furniture, fencing and retaining walls, a common example is the seat and back slats of your garden bench and table furniture
  • Material / Coating: Galvanised is a dull greyish colour and can be a little rough in appearance and is mainly used outdoors because of its superior corrosion resistance and proven longevity. Also known as HDG, it is one of the best coatings for protection against rust. Galvanised fasteners have been used across many industries in Australia for over 150 years, roofing, steel buildings, trailers, bridges, fencing, power poles, marina’s, are just a few examples. Recently we have seen a lot of new coatings developed, terms like class 3, class 4, B8, climseal, mechanical galvanised and ruspert are all variations of the original galvanising
  • Grade v Class Difference: Imperial fastenings are referred to as grades, and metric fastenings are referred to as classes. Both have marking systems that make it possible to determine grade and class. An example is a ½” UNC bolt with 5 lines on the head is grade 8 and 3 lines is grade 5, both are regarded as high tensile. Metric bolts are slightly different, if it has 4.6 then it is mild steel and 8.8 is high tensile. The markings on a stainless fastener indicate the grade of material and strength, e.g. material G304 grade will have one of the following markings: A2-70, G304, A2, 304 and G316 grade stainless will have one of the following: A4-70, G316, A4, 316
  • Thread Pitch (Metric): Pitch means the distance between the peaks of two threads along a screw, bolt, or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example, a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm
  • Fastener length: is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. Thus, fasteners with heads that sit above the surface are measured from under the head to the end of the fastener, while fasteners that sit flush with the surface are measured from the top of the head to the end of the fastener
  • Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
  • Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as height, width, visible stamped markings, appearance or actual finish
  • Photos: are of the product but may not be the actual diameter, height, width, length you may require, always refer to the size in the description and additional specifications data provided prior to ordering
  • Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Fastener Kits Online is not responsible for any loss, claim or damages arising therefrom. In developing this information, Fastener Kits Online has made a determined effort to present it accurately
  • Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
  • Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
  • Prices: Include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
Specification 
Item Length (From Under Head)350mm (150mm Thread)
TypeCup Head Bolt & Nut
Head StyleCup Head
Diameter Size12mm | M12
Size x PitchM12 x 1.75p Coarse
Bolt SizeM12 (12mm)
Thread Size1.75mm
Thread TypeMetric - Coarse
System of MeasurementMetric
Thread DirectionRight Hand
Length350mm
Closest Size in Imperial1/2"
Thread Length TChoose your length to view
Thread Length Approx Int150mm
Product Diameter D11.73 - 12.00mm
Head Height H6.00 - 6.80mm
Head Diameter A24.70 - 27.00mm
Square Under Head Width As11.30 - 12.70mm
Drive TypeHex
MaterialCarbon Steel
GradeLow Tensile Class 4.6
FinishGalvanised
Corrosion Protection LevelExcellent
StandardAS1390:1997 & AS1112:2000
BrandHobson Engineering
Alternative BrandsBremick Fasteners | Brighton Best
MPNKBC46GCM120350, CMC612350GN, BCHMG123501, 627264
UPC9314818675987, 9337357031274, 662403162435
Number In Pack1
ebay listing template design by dZine-hub