Product Description
41a5034 Garage Door Opener Safety Beam Kit
The sending sensor (with an amber LED)transmits an invisible light beam to the receiving sensor(with a green LED).If an obstruction breaks the light beam while the door is closing, the door will stop and reverse to the full open position,and the garage door opener lights will flash 10 times.
- 41a5034 Garage Door Opener Safety Beam Kit Replacement Models: G801CB-P, 2610459, 012381050345, 041A5034.
- Be sure disconnect the power from door openers before installing the safety reversing sensor.
- The sensor beam must install not higher than 6 inch (15cm) above the garage door.
41A5034 Garage Safety Sensors Kit
Compatible with
Compatible with Craftsman 13953962SRT,13930437,13953993DM,13957915,13953991SRT,13957918,13953916D,13953925DS,13953904D,
13953971SRT,13954918,13954915,13953966SRT1,13953962SRT1,1393043,3280-267,13954990,13953985DM,2280,13953920D,13953974SRT,13918451D,WD962KLD,1255R,13954985,1395398511,13953964SRT,13953906D,13953990DS,13953918D,13953905DM,13953901DM,13953997D,13953985D,13918452D,13953920DM,1265LM,13953977SRT,13953975SRT1,1395399211,13954930,1240R,13954931,139539511,2280-267,Compatible with LiftMaster: 985, 1265, 1345, 1346, 1355, 2110, 2220, 2245, 2255, 2265, 2280, 2500, 2565, 2575, 2580, 2585, 2595, 3110, 3130, 3220, 3240, 3245, 3255, 3265, 3270, 3275, 3280, 3500, 3575, 3585, 3595, 3800, 3840, 3850, 1000SDR, 1240R, 1245R, 1246R, 1255R, 1256R, 1280R, 2000SDR, 2500B, 2500B, 2500D, 3130M, 3240M, 3245M, 3255M, 3265M, 3280M, 3575S, 3585S, 3595S, 3800P, 3800PLD, ATS2113X, ATS211R, ATS211X. (Not all models listed). Compatible with Models: 1200, 2200, 4200, 4620, 4640, 6200, 7220, Compatible with 2280 and WD962.
Three Installation Methods
|
|
|
|---|---|---|
Option A DOOR TRACK INSTALLATION1.Slide the curved arms of the sensor bracket around the edge of the door track.Snap into place so that the sensor bracket is flush against the track. 2.Slide the carriage bolt into the slot on each sensor. 3.Insert the bolt through the hole in the sensor bracket and attach with the wing nut.The lenses on both sensors should point toward each other.Make sure the lens is not obstructed by the sensor bracket. | OPTION B WALL INSTALLATIONIf additional clearance is needed an extension bracket (not provided)or wood blocks can be used. Make sure each bracket has the same amount of clearance so they will align correctly. 1.Position the sensor bracket against the wall with the curved arms facing the door.Make sure there is enough clearance for the beam to be unobstructed.Mark holes. 2.Drill 3/16 inch pilot holes for each sensor bracket and attach the sensor brackets to the wall using lag screws (not provided). 3.Slide the carriage bolt into the slot on each sensor. 4.Insert the bolt through the hole in the sensor bracket and attach with the wing nut.The lenses on both sensors should point toward each other.Make sure the lens is not obstructed by the sensor bracket. | OPTION C FLOOR INSTALLATIONUse an extension bracket (not provided)or wood block to raise the sensor bracket if needed. 1.Carefully measure the position of both sensor brackets so they will be the same distance from the wall and unobstructed. 2.Attach the sensor brackets to the floor using concrete anchors(not provided). 3.Slide the carriage bolt into the slot on each sensor. 4.Insert the bolt through the hole in the sensor bracket and attach with the wing nut.The lenses on both sensors should point toward each other.Make sure the lens is not obstructed by the sensor bracket. |
