Edelbrock 2116 Ansaugkrümmer passend für Small-Block Chevy w/Vortec Heads 

Edelbrock 2116 Intake Manifold for Small-Block Chevy w/Vortec Heads 

Passend für / Fits for

Edelbrock part #2116 Performer intake manifold is based on the popular and powerful Edelbrock #2101, this dual-plane intake is designed for the street rod, industrial and engine swap market utilizing 262-400 c.i.d. Chevy V8's with 1996 and later Vortec (L31) cast iron or the Edelbrock E-Tec aluminum heads. Edelbrock's Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent throttle response from off-idle through 5500rpm. Manifold has provisions for external water bypass and may be used on either Vortec blocks or 1995 and earlier blocks. No provision for exhaust heated chokes.


Specs


ApplicationApplication Specific
UPC00085347021161
SeriesPerformer
Gasket Or Seal IncludedNo
Vehicle ModelChevrolet
Availability NoteAvailable to Order
Warranty12 Months
Ec Basic Operating Rpm RangeIdle-5500 RPM
Emissions Code
Hazardous Materials WarningWARNING: This product can expose you to Lead, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes
  • Recommended intake gasket: Edelbrock #7235; Manifold ht: A-3.87", B-5.28"; Carb pad height: 4.57"; Carb recommendations: OEM 4-Bbl (pre-1981, Electric choke ONLY) Use #8032 throttle bracket. Edelbrock AVS2 Series or Performer Series 500-650cfm, use bracket #8032 for 1972-78.; Port exit dimensions: 2.05" tall with slanted side walls; Use RTV sealant to properly seal end seals, such as Edelbrock High Temp Silicone sealant #1076, DO NOT USE END SEALS GASKETS.; Sealant must be used on intake bolt threads if the threads extend into lifter valley or coolant passage.; NPT/Pipe thread fittings require the use of Teflon tape or paste on threads to ensure proper seal.; DO NOT OVERTIGHTEN NPT/Pipe fittings, this may cause the aluminum to crack around the fitting boss. NPT/Pipe thread is a tapered thread.; Hardened washers Must be used with intake bolts to ensure proper torque and prevent galling of the aluminum.; Stock brackets will require modification to fit the upright manifold bolt holes.; Will not fit under stock Corvette hood.; Even though manifolds are compatible with EGR systems, this does not mean they are legal for use on emissions controlled vehicles. Check local laws for legality.; Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.
Center Maximum Height4.570 in
CNC PortedNo
FinishSatin
Front Maximum Height3.870 in
MaterialAluminum
Rear Maximum Height5.280 in
Single Or Dual Plane TypeDual

OEM Nr.

2116

Schneller Versand

24h Express oder Standardversand

Sicherheit

30 Tage Rückgaberecht

Beratung

Kundenservice von KFZ-Experten

Bitte überzeigen Sie sich vor dem Kauf davon, dass die angebotenen Teile die passenden für Ihr Fahrzeug sind! Wenn Sie sich nicht sicher sind, ob die angebotenen Teile die passenden für ihr Fahrzeug sind, schicken  Sie uns die Fahrgestellnummer ihres Fahrzeuges. Wir prüfen das für Sie! Bei Fragen zu den Artikeln stehen wir Ihnen gerne zur Verfügung! Wir sind immer glücklich ihnen helfen zu können!

Please make sure that this is the correct part for your car. If you have any questions please contact us.  If you are not sure this is the correct item for your car, you can send us VIN number of your vehicle and we will check it for you! If you have any questions about this item, please ask. We are always happy to help you!