Natural Stone Sealer - WET LOOK
Smartseal Natural Stone Sealer WET LOOK is a water-based protective sealer that creates a durable, clear silk/satin finish. It can be used on internal and external surfaces made from sandstone**(see exceptions below), limestone, slate, terracotta, quarry and Victorian tiles, brick pavers and any textured stone or masonry surfaces. Smartseal Natural Stone Sealer WET LOOK is rapid drying and very easy to apply. It will provide protection to the applied surface against oil and water-based stains. Ideal for Natural Stone**(see exceptions below) & Slate Provides a Silk/Satin or "Wet-look" finish Ok for rough & absorbent surfaces Suitable for outdoor or indoor use Please take a look at the other sealers for natural stone such as the DRY finish Natural Stone Sealer. For a colour enhancing sealer for natural stone that is not a gloss finish, you might want to consider the Natural Stone COLOUR ENHANCER. *WE DO NOT RECOMMEND USING ON POLISHED STONE & CERAMIC GLAZED SURFACES, AS IT WON'T SOAK INTO THE SURFACE* **Exceptions to Sandstone suitability: Please note this product is not suitable for Kandla Grey (mid and light grey) sandstone. Technical COVERAGE RATIOS: Average 5-12 m² per litre depending on the texture and porosity of the surface being sealed. APPLICATION INSTRUCTIONS: Due to the effects of Efflorescence and Natural Salts and Minerals, that can permeate through Natural Stone, it is recommended not to seal for a minimum 4 months after installation. 1. Apply in temperatures above 15°C, but below 23 degrees ensuring the surface is completely dry, clean and free from debris. Apply only if no rain is forecast for at least 8 hours. For best cleaning results use Patio Clean Xtreme. **If applied to a surface where a "sweep-in" pointing compound has been used with the last 6 months, the natural stone must be fully cleaned with Smartseal Residue Remover prior to sealant application.** 2. Apply the sealer thinly and evenly with a low pressure sprayer, roller, microfibre mop, paint brush or soft cloth. Try not to leave application marks or allow the product to 'pool' or 'puddle' on the surface immediately after application. In the event of over application please ensure all excess is removed within 45 minutes of applying. 3. Once applied, allow minimum 60 minutes drying time before applying the second coat. If possible, apply the product in the opposite direction to try to achieve an even finish. Multiple coats can be applied to achieve the desired finish. Important Note: Any areas nearby that are not being sealed should be protected with masking materials. If you are sealing over coloured grouts, carry out that a stain test before proceeding.

Natural Stone Sealer - WET LOOK

£
79.95

Ask a question Related items

Natural Stone Sealer - WET LOOK

https://www.youtube.com/watch?v=

Smartseal Natural Stone Sealer WET LOOK is a water-based protective sealer that creates a durable, clear silk/satin finish. It can be used on internal and external surfaces made from sandstone**(see exceptions below), limestone, slate, terracotta, quarry and Victorian tiles, brick pavers and any textured stone or masonry surfaces.Smartseal Natural Stone Sealer WET LOOK is rapid drying and very easy to apply. It will provide protection to the applied surface against oil and water-based stains. 
  • Ideal for Natural Stone**(see exceptions below) & Slate
  • Provides a Silk/Satin or "Wet-look" finish
  • Ok for rough & absorbent surfaces
  • Suitable for outdoor or indoor use
Please take a look at the other sealers for natural stone such as the DRY finish Natural Stone Sealer. For a colour enhancing sealer for natural stone that is not a gloss finish, you might want to consider the Natural Stone COLOUR ENHANCER.*WE DO NOT RECOMMEND USING ON POLISHED STONE & CERAMIC GLAZED SURFACES, AS IT WON'T SOAK INTO THE SURFACE***Exceptions to Sandstone suitability: Please note this product is not suitable for Kandla Grey (mid and light grey) sandstone.

Technical
COVERAGE RATIOS: Average 5-12 m² per litre depending on the texture and porosity of the surface being sealed.APPLICATION INSTRUCTIONS:Due to the effects of Efflorescence and Natural Salts and Minerals, that can permeate through Natural Stone, it is recommended not to seal for a minimum 4 months after installation.1. Apply in temperatures above 15°C, but below 23 degrees ensuring the surface is completely dry, clean and free from debris. Apply only if no rain is forecast for at least 8 hours. For best cleaning results use Patio Clean Xtreme.**If applied to a surface where a "sweep-in" pointing compound has been used with the last 6 months, the natural stone must be fully cleaned with Smartseal Residue Remover prior to sealant application.**2. Apply the sealer thinly and evenly with a low pressure sprayer, roller, microfibre mop, paint brush or soft cloth. Try not to leave application marks or allow the product to 'pool' or 'puddle' on the surface immediately after application. In the event of over application please ensure all excess is removed within 45 minutes of applying.3. Once applied, allow minimum 60 minutes drying time before applying the second coat. If possible, apply the product in the opposite direction to try to achieve an even finish. Multiple coats can be applied to achieve the desired finish.Important Note:  Any areas nearby that are not being sealed should be protected with masking materials. If you are sealing over coloured grouts, carry out that a stain test before proceeding.

Driveways

Patios

Bricks & Masonry

Concrete

Wood & Decking

Roofs