Now with German and English instructions as PDF file after purchase.
Leider
werden von Nichicon keine Audio-Elkos mehr produziert.
Sie sind
"END OF LIFE".
Das gilt ebenso für die Elna Silmic II und Rubycon Black
Gate.
Wir haben uns bevorratet und bieten diesen Reparatursatz an, solange der Vorrat reicht.
Für Vorschläge zu einer passenden Alternative bedanken wir uns.
REVOX A77 Reparatursatz NICHICON FINE GOLD KOMPLETT. TOP Klangqualität.
Für alle Versionen der Revox A77, von MK I bis MK IV (MK 1 bis MK 4)
Bestehend aus sehr hochwertigen Bauteilen:
NICHICON FINE GOLD Audiokondensatoren 100% Original, Made in Japan
PANASONIC FC 4,7µF Low ESR für die Tape-Drive-Control und Switch Platine
Gekapselte PIHER Trimmer
Passende Motorkondensatoren
Fischer & Tausche Netzteil-Kondensator
WIMA, Panasonic, Epcos... Entstör-Kondensatoren
Es ist Ersatz für ALLE Elektrolyt- Tantal- Entstör- und Motor-Kondensatoren und für ALLE Trimmer enthalten, die in der Revox A77 verbaut sind.
Alle radialen und axialen Elkos, sowie alle Tantals werden durch radiale Elkos ersetzt.
Nicht enthalten sind die Bauteile für eventuell verbaute Endstufen-, Dolby-, oder sonstige optionale Platinen.
Einzeln in Tüten verpackt und den Platinen zugeordnet.
Je nach Version werden ein paar Bauteile übrig bleiben.
Aufgrund des Alters der Maschine wird dringend empfohlen, diese Bauteile zu ersetzten.
Die alten Miniprint-Kondensatoren sind bekannt dafür, dass Sie sich in Rauch auflösen.
Die meisten Franko und Siemens Elkos sind mittlerweile defekt.
Bei den Trimmern rosten und brechen einfach die Schleifkontakte.
Zum Thema Bypasskondensatoren, bzw. Koppelkondensatoren:
Dafür gibt es nach meiner Überzeugung absolut keine Notwendigkeit.
Wer den doppelten Aufwand haben möchte, kann dies natürlich tun...
Lieferumfang:
Elko's und Trimmer für alle 7 Audio-Platinen wie folgt:
1 x für 1.077.700 Eingangs-Vorverstärker ( Input Amplifier )
2 x für 1.077.705 Aufnahme-Verstärker ( Record Amplifer )
1 x für 1.077.715 Aufnahme Relais ( Record Relay )
1 x für 1.077.712 Oszillator ( Oscillator )
2 x für 1.077.720 Wiedergabeverstärker ( Playback Amplifier )
Elko’s, Trimmer, Motorkondensatoren, Ersatz für Rifa Miniprint-Kondensatoren wie folgt:
1 x für 1.077.540 Netzteil ( Power Supply )
1 x für 1.077.370 Laufwerkssteuerung ( Drive Control )
1 x für Motorkondensatoren ( Motor Capacitors )
1 x für 1.077.725 Drehzahlregelung SPULE-Version ( Speed Control COIL-Version )
1 x für 1.077.724 / 729 Drehzahlregelung IC-Version ( Speed Control IC-Version )
1 x für 1.077.435 Schalterprint ( Switch Board )
Ihre Vorteile:
- Wir verkaufen ausschliesslich hochwertige und originale Bauteile aus aktueller Produktion.
- Mit dem Versand der Bauteile erhalten Sie gleichzeitig per E-Mail oder als Download-Link eine ausführlicher Anleitung Deutsch / Englisch mit Schaltplan und Platinen-Layout als .pdf Datei. (Bitte prüfen Sie Ihren SPAM-Ordner, fall Sie keine Anleitung bekommen haben)
- Wir verkaufen nur Bauteile, die wir selber in unserer Werkstatt verwenden und in den jeweiligen Maschinen getestet haben.
-
Wir verkaufen nur Bauteile, die in dieser Kombination auch
funktionieren, denn das ist bei einer Zusammenstellung nach Schaltplan
häufig nicht der Fall. Schaltpläne enthalten häufig auch Fehler, es gab
z.B. auch damals Updates und neue Revisionen.
- Wir verkaufen nur Bauteile, mit denen die Werks-Spezifikationen eingehalten, bzw. sogar meistens auch übertroffen werden.
- Bei Fragen, oder Problemen sind wir für Sie da und helfen gerne weiter.
Mit diesen Bauteilen wurden mehrere hundert Maschinen umgebaut, ohne eine einzige Reklamation.
In diesem Set sind alle relevanten anfälligen und ausfallgefährdeten Bauteile enthalten.
In der Einbau-Anleitung wird beschrieben wie die alten Trimmer mit einem Multimeter durchgemessen werden.
Danach werden die neuen Trimmer erst auf diesen Widerstandswert eingestellt und anschliessend eingelötet.
So lässt sich in den meisten Fällen eine Neueinmessung umgehen.
Lötkenntnisse und Elektronik-Grundwissen muss vorhanden sein !!!
Auf keinen Fall einfach so an der Maschine herumschrauben, die Gefahr etwas zu verstellen, oder zu beschädigen ist sehr hoch !!!
Vorsichtsmassnahmen:
In dem Gerät existieren lebensgefährliche Spannungen!
Bitte ziehen Sie bei allen Arbeiten am Gerät den Netzstecker!
Achten
Sie bitte darauf das keine Teile verlorengehen oder in das Gerät
fallen! Wir übernehmen keine Verantwortung für die durchgeführten
Arbeiten !
Bei
diesem Artikel handelt es sich um einen individuell für Sie
zusammengestellten und personalisierten Artikel.
Die
Einbauanleitung die Sie als PDF Datei erhalten ist ebenso Bestandteil
dieses Artikels.
Eine Rücknahme ist somit leider nicht möglich.
Wir bitte um Verständnis.
Auf den unteren Fotos sehen Sie beispielhaft ein paar umgebaute Platinen, sowie die alten Bauteile, die ersetzt wurden. (Diese Teile sind nicht Bestandteil des Angebots !!!)
ENGLISH:
Unfortunately,
Nichicon no longer produces audio electrolytic capacitors. Production
has been discontinued for all audio electrolytic capacitors up to
approx. 100µF. They are "END OF LIFE". This also applies to the Elna
Silmic II and Rubycon Black Gate.
We have stocked up and are offering this repair kit while stocks last.
Thank you for suggestions for a suitable alternative.
PREMIUM REVOX A77 repair kit NICHICON FINE GOLD COMPLETE. TOP sound quality.
For all versions of the Revox A77, from MK I to MK IV (MK 1 to MK 4)
Consists of very high quality components:
NICHICON FINE GOLD audio capacitors 100% Original, Made in Japan
PANASONIC FC 4,7µF Low ESR for Tape-Drive-Control and Switch board
Encapsulated PIHER trimmer
Suitable motor capacitors
Fischer & Tausche power supply capacitor
WIMA, Panasonic, Epcos... suppression capacitors
Include replacement for ALL electrolytic, tantalum, suppression and motor capacitors and for ALL trimmers that are installed in the Revox A77.
All radial and axial electrolytic capacitors as well as all tantalum are replaced by radial electrolytic capacitors.
Not included are the components for any built-in power amplifier, Dolby, or other optional boards.
Individually packed in bags and assigned to the circuit boards.
Depending on the version, a few components will be left over.
Due to the age of the machine, it is strongly recommended that these components be replaced.
The old mini print capacitors are known to go up in smoke.
Most of the Franko and Siemens electrolytic capacitors are now defective.
With the trimmers, the sliding contacts simply rust and break.
On the subject of bypass capacitors or coupling capacitors:
I believe there is absolutely no need for that.
If you want double the effort, you can of course do so …
Scope of delivery:
Capacitors and trimmers for all 7 audio boards as follows:
1 x für 1.077.700 Eingangs-Vorverstärker ( Input Amplifier )
2 x für 1.077.705 Aufnahme-Verstärker ( Record Amplifer )
1 x für 1.077.715 Aufnahme Relais ( Record Relay )
1 x für 1.077.712 Oszillator ( Oscillator )
2 x für 1.077.720 Wiedergabeverstärker ( Playback Amplifier )
Capacitors, trimmers, motor capacitors, replacement for Rifa miniprint capacitors as follows:
1 x für 1.077.540 Netzteil ( Power Supply )
1 x für 1.077.370 Laufwerkssteuerung ( Drive Control )
1 x für Motorkondensatoren ( Motor Capacitors )
1 x für 1.077.725 Drehzahlregelung SPULE-Version ( Speed Control COIL-Version )
1 x für 1.077.724 / 729 Drehzahlregelung IC-Version ( Speed Control IC-Version )
1 x für 1.077.435 Schalterprint ( Switch Board )
Your advantages:
- We only sell high-quality and original components from current production.
- When the components are dispatched, you will receive detailed
instructions in German / English with a circuit diagram and circuit
board layout as a .pdf file by email or as a download link. (Please check your SPAM folder if you have not received any instructions)
- We only sell components that we use ourselves in our workshop and have tested in the respective machines.
-
We only sell components that also work in this combination, because
this is often not the case with a combination according to the circuit
diagram. Circuit diagrams often also contain errors, e.g. even then
updates and new revisions.
- We only sell components with which the factory specifications are adhered to, or in most cases even exceeded.
- If you have any questions or problems, we are there for you and will be happy to help.
Several hundred machines were converted with these components without a single complaint.
This set contains all relevant vulnerable and failure-prone components.
The installation instructions describe how the old trimmers are measured with a multimeter.
Then the new trimmers are first set to this resistance value and then soldered in.
In this way, a new measurement can be avoided in most cases.
Soldering skills and basic electronics knowledge must be available!
In no case simply screw around the machine, the risk of adjusting something or damaging it is very high!
Precautions:
Lethal voltages exist in the device!
Please pull the power plug when working on the device!
Please make sure that no parts are lost or fall into the device! We do not take any responsibility for the work done!
This
item is an individually compiled and personalized item for you.
The
installation instructions that you receive as a PDF file are also
part of this item.
A return is unfortunately not possible. We ask
for your understanding.
Ich
weise darauf hin dass, sofern nicht gesondert oben im Text angegeben,
dieses Produkt ein präzise nachgefertigtes Ersatzteil ist und nicht
ein Original Teil des Herstellers. Rechtlich geschützte Markennamen
sowie Warenbezeichnungen, Gerätebezeichnungen und original
Ersatzteilenummern oder Bezeichnungen gehören den jeweiligen
Eigentümern und dienen ausschließlich der Erklärung zu welchem
Gerät der angebotene Artikel zugeordnet werden kann
(Kompatibilitätskennzeichnung).
Einfuhrzölle,
Steuern und Abgaben sind nicht im Artikelpreis oder den Versandkosten
enthalten. Diese Gebühren trägt der Käufer. Bitte erkundigen Sie
sich vor dem Bieten/Kaufen bei den Zollbehörden Ihres Landes, welche
zusätzlichen Kosten anfallen. Diese Gebühren werden normalerweise
von der liefernden Spedition (Versandunternehmen) oder bei Abholung
des Artikels erhoben. Verwechseln Sie sie nicht mit zusätzlichen
Versandkosten.
Please
note that, unless otherwise stated above, this product is a precisely
manufactured replacement part and not an original part from the
manufacturer. Legally protected brand names, product names, device
names, and original spare parts numbers or designations belong to
their respective owners and serve solely to indicate the device to
which the offered item can be assigned (compatibility marking).
Import
duties, taxes, and charges are not included in the item price or
shipping charges. These charges are the buyer's responsibility.
Please check with your country's customs authorities to determine
what these additional costs will be prior to bidding/buying. These
charges are normally collected by the delivering freight (shipping)
company or when you pick the item up. Do not confuse them for
additional shipping charges.