Specifications:
Liner material: stainless steel
Voltage: 220V
Power: 11KW/15KW/18KW
Phase: single phase
Connection size: 40 mm (1.57 ")
Machine size: 49 x 10 x 38 cm / L x W x H.
Suitable for: hot tub & swimming pool equipment

The thermostat must work with a water pump with an appropriate capacity.
(If the pump and thermostat do not match, the flow rate is too low, the heating pipe is dry and can easily be damaged.)
5.5KW-15KW heaters must operate with a pump with a water flow of at least 177 ft³ / hour (5m³/hour).
18KW-36KW heaters must operate with a pump with a water flow of at least 353 ft³ / hour (10m³/hour).
40KW-60KW heaters must operate with a pump with a water flow of at least 530 ft³ / hour (15m³/hour).

●The 1KW is suitable for 1 ft³
●The 5.5KW thermostat is suitable for ≤ 127 ft³ pool / 3.6m³
●The 9KW thermostat is suitable for a pool with ≤ 212 ft³ / 6m³
●The 11KW thermostat is suitable for a pool with ≤ 259 ft³ / 7.3m³
●The 15KW thermostat is suitable for a pool of ≤ 353 ft³ / 10m³
●The 18KW thermostat is suitable for a pool with ≤ 424 ft³ / 12m³

It is recommended to use the thermostat with a circulating water pump:
1.Operating procedure: first turn on the water pump and then the thermostat.
2.Shutdown: First turn off the thermostat, wait a while (10 seconds to 1 minute depending on the performance of the thermostat) and then turn off the pump.
3.Reliable leak protection devices must be installed and commissioned by the responsible electrician. Monthly maintenance and inspection.

4.The additional heating effect of the thermostat is better. Direct heating requires the use of a more powerful machine.

💟 Please Note:
1.If an error occurs, the pool heater will stop immediately and a message will appear on the control panel so that the user or technician can determine where the error is. The safety of the customer is a top priority.
2.Prohibit the use of seawater or salt-added disinfectants to sterilize thermostats(Excessive chlorine in disinfecting water is not good either, About 5 grams of water per cubic meter), as highly concentrated saltwater is very corrosive to stainless steel.

NOTE

1.This machine can be used with Single-phase 220V or dual-phase 110V
2.please confrim the wire referring to the power of the unit,here are the  current of different type of machine
9KW/220V = 41A,about 41A
11KW/220V =50A, about 50A
15KW/220V =68A,about 68A
18KW/220V =82A,about 82A
3.This was not an instant water heater,the thermostat circulates with a water pump, and the heat generated will be immediately brought into the swimming pool by the circulating water. Under appropriate circumstances, the temperature of the entire swimming pool will slowly increase,and it takes a little longer to heat up for the first time.

⭐【Manual reset temperature switch】
Prevent water from burning dry and protect the pool heater from overheating.
⭐【Automatic shutdown in case of lack of water】
The thermostat will not work if the pump does not start. It can effectively prevent water shortage and non-standard operation from damaging the machine.
⭐【Temperature limit switch】
It will turn off automatically when the temperature reaches the temperature, and it can automatically start the heating function after the temperature is lowered, which can effectively prevent damage from excessive machine temperature.
⭐【Fuse protection】
If the current is too large, the circuit breaker is immediately disconnected and the power supply interrupted.
⭐【Power protection switch】
Use the AC contactor as a start switch. Regardless of the type of accident, you can quickly disconnect the power supply and protect the safety of the machine and people.
⭐【Smart self-diagnosis function】
The control system continuesly monitors the operating status of all parts of the heater and reacts quickly and displays appropriate notification messages for each event to prevent from damage or malfunctions.