Exact items shown, Advanced Motion Controls (AMC) DigiFlex digital servo drive/amplifier.
- AMC configuration/model: DR102RE15A40NACB VS1
- Viasat description: Servo Amplifier Assy.
- Viasat P/N: 1025767 Rev. 4
New old stock Viasat surplus. These units remain unopened in their static-shield packaging. Please review the photos for the exact condition, configuration and identification labels.
I located the Advanced Motion Controls DR100RE15A40NAC.pdf manual, which covers a similar DR100RE-series servo drive. It may also apply to these DR102 units, but I have not confirmed that the specifications or pinouts in that manual are identical to these units. You can acquire that manual by contacting AMC at https://portal.a-m-c.com/support/contact-us/ and requesting it, you will need to make an account to do so.
There are two units available, you are buying one at a time, please choose the quantity you want from the dropdown list.
The information below is from that manual:
DESCRIPTION:
The DR100RE Series digital PWM servo drives are designed to drive brushed and brushless servomotors. These fully digital drives operate in torque, velocity, or position mode and employ Space Vector Modulation (SVM), which results in higher bus voltage utilization and reduced heat dissipation. The command source can be generated internally or can be supplied externally. In addition to motor control, these drives feature dedicated and programmable digital and analog inputs and outputs to enhance interfacing with external controllers and devices.
DR100RE Series drives feature a single RS232/485 interface, which is used for drive configuration and setup as well as online operation in networked applications. Drive commissioning can be accomplished through a fully graphical Windows© based application.
All drive and motor parameters are stored in non-volatile memory.

SPECIFICATIONS:
| POWER STAGE SPECIFICATIONS | DR100RE15A40NAC |
| AC SUPPLY VOLTAGE | 40 - 250 VAC, 1 or 3 phase, 50 - 60 Hz |
| PEAK CURRENT | 15A (10.6 Arms) |
| MAXIMUM CONTINUOUS CURRENT | 7.5A (5.3 Arms) |
| MINIMUM LOAD INDUCTANCE | 600 µH |
| SWITCHING FREQUENCY | 20 kHz |
| HEATSINK (BASEPLATE) TEMPERATURE RANGE | 0 to 65 °C, disables at 65 °C |
| POWER DISSIPATION AT CONTINUOUS CURRENT | 200W |
| MIN. UNDER-VOLTAGE SHUTDOWN | 55 VDC |
| MAX. OVER-VOLTAGE SHUTDOWN | 395 VDC |
| BUS CAPACITANCE | 660 µF |
| MECHANICAL SPECIFICATIONS |
| MOTOR & POWER CONNECTOR: P1 | Removable screw terminal |
| MOTOR FEEDBACK CONNECTOR: CN3* | 15-pin high density female D-sub |
| I/O CONNECTOR: CN2* | 26-pin high density female D-sub |
| COMMUNICATIONS INTERFACE (RS232/485): CN1* | 9-pin female D-sub |
| SIZE | 6.99 x 5.50 x 2.20 inches 177.5 x 139.7 x 55.9 mm |
| WEIGHT of units in this listing | 2 lbs 9 oz |
* Mating connectors are not included.
PIN FUNCTIONS:
P1 - Motor and Power Connector:
| PIN | NAME | DESCRIPTION | I/O |
| 1 | MA | Motor phase A | O |
| 2 | MB | Motor phase B | O |
| 3 | MC | Motor phase C | O |
| 4 | DC+ | External shunt regulator connection | O |
| 5 | DC- | External shunt regulator connection | O |
| 6 | AC1 | AC supply input. 40 - 250 VAC, single or three phase. | I |
| 7 | AC2 | AC supply input. 40 - 250 VAC, single or three phase. | I |
| 8 | AC3 | AC supply input. 40 - 250 VAC, single or three phase. | I |
CN3 - Motor Feedback Connector:
| PIN | NAME | DESCRIPTION | I/O |
| 1 | N/C | Not connected | |
| 2 | N/C | Not connected | |
| 3 | N/C | Not connected | |
| 4 | REF+ | Resolver reference (excitation) output. 4Vrms @ 5kHz. | O |
| 5 | REF- | Resolver reference (excitation) output. 4Vrms @ 5kHz. | O |
| 6 | SIN+ | Resolver sine input. 2Vrms | I |
| 7 | SIN- | Resolver sine input. 2Vrms | I |
| 8 | COS+ | Resolver cosine input. 2Vrms | I |
| 9 | COS- | Resolver cosine input. 2Vrms | I |
| 10 | N/C* | Not connected | |
| 11 | N/C* | Not connected | |
| 12 | SGND | Signal ground | SGND |
| 13 | +5V OUT | +5V @ 250mA max. Short-circuit protected. | O |
| 14 | PAI3 | Programmable analog input, single ended, 10-bit | I |
| 15 | N/C* | Not connected | |
* Contact factory for SR compatible options.
CN2 - I/O Connector:
| PIN | NAME | DESCRIPTION | I/O |
| 1 | PDO1* | Programmable digital output | O |
| 2 | SGND | Signal ground | SGND |
| 3 | PDO2* | Programmable digital output | O |
| 4 | +REF | Differential reference signal input, 14-bit resolution. Can also be used as programmable analog input 1. | I |
| 5 | -REF | | I |
| 6 | PAI2 | Programmable analog input | I |
| 7 | PAO1 | Programmable analog output | O |
| 8 | PAO2 | Programmable analog output | O |
| 9 | -PDI6 | Programmable Input (see CN2-18) or Direction- or Aux Enc B- | I |
| 10 | PDO3 | Programmable digital output | O |
| 11 | PDI1 | Programmable digital input | I |
| 12 | PDI2 | Programmable digital input | I |
| 13 | PDI3 | Programmable digital input | I |
| 14 | PDO4 | Programmable digital output | O |
| 15 | +5V OUT | +5VDC. Note: the total current on CN2-15 and CN3-13 combined should not exceed 250 mA | O |
| 16 | SGND | Signal ground | SGND |
| 17 | +PDI5 | Programmable differential digital input, or Step+ or Aux Enc A+ | I |
| 18 | +PDI6 | Programmable, differential digital input or Direction+ or Aux Enc B+ | I |
| 19 | PDI4 | Programmable digital input | I |
| 20 | Enc A+ | Emulated channel A output. (10, 12, 14, or 16 bit resolution) | O |
| 21 | Enc A- | Emulated channel A output. (10, 12, 14, or 16 bit resolution) | O |
| 22 | Enc B+ | Emulated channel B output. (10, 12, 14, or 16 bit resolution) | O |
| 23 | Enc B- | Emulated channel B output. (10, 12, 14, or 16 bit resolution) | O |
| 24 | Enc I+ | Emulated index output. High when channel A and B, or both low | O |
| 25 | Enc I- | Emulated index output. High when channel A and B, or both low | O |
| 26 | -PDI5 | Programmable Input (See CN2-17) or Step- or Aux Enc A- | I |
* Contact factory for SR compatible options.
CN1 - Communications Interface (RS232/485):
| PIN | NAME | DESCRIPTION | I/O |
| 1 | SELECT | RS232/485 selection. Pull to ground (CN1-5) for RS485. | I |
| 2 | TX/+TX | RS232: Transmit; RS485: +TX | O |
| 3 | RX/+RX | RS232: Receive; RS485: +RX | I |
| 4 | N/C | Not connected | |
| 5 | SGND | Signal ground | SGND |
| 6 | -TX | RS485: -TX | O |
| 7 | N/C | Not connected | |
| 8 | -RX | RS485: -RX | I |
| 9 | N/C | Not connected | |
Note to me: Garage, Right Rear
I normally ship within 24 hours of your order, but the post office does not always initiate tracking when I put the packages in the drop off box.
Check out my other items!