Phonak Retention Locks Power (P) Pack of 10
Genuine Phonak Accessory

Phonak Retention Locks (Power) · Sport Locks · Pack of 10

Run by qualified audiologists·30-day returns·Tracked delivery

Dispatched from the UK Genuine Phonak Sport lock retention For SDS 4.0 / 5.0 / 6.0 receivers · Power (P) · Pack of 10 Pre-shapeable to ear concha

Keep your Phonak hearing aids securely in place during everyday wear and active movement. Phonak Retention Locks - also called sport locks - are small flexible arms that slide onto your existing receiver wire and loop discreetly into the bowl of your ear. They stop the receiver and dome working their way out of the ear canal during talking, chewing, sport, or any vigorous movement.

Pack of 10, sized for Power (P) power receivers. If your receiver tip is marked with a "P", this is the correct retention lock.

Product Type Sport lock retention - SDS 4.0 / 5.0 / 6.0
Power Match Power (P) receivers only
Replace When Lock loses spring or shows visible cracks
Pack Size 10 retention locks per pack
⚠ Three retention lock sizes exist for Phonak / Unitron. If your receiver is marked "S" (Standard) or "M" (Medium), this Power size will not fit correctly - you most likely need Phonak Retention Locks Standard (S) or Medium (M) (different size) instead. Check the small letter printed on the receiver tip, then see below to confirm.
Different size? - Same Phonak retention lock, different power size
Standard (S) → Medium (M) → ★ Power (P) (this listing)

Phonak and Unitron retention locks come in three sizes - Standard (S), Medium (M), and Power (P). Look at the small letter printed on your receiver tip to find the right row below.

Size Fits receivers Status
Power (P) If your receiver tip shows a small "P", this is your size.

Fits Power (high-output) receivers across SDS 6.0 / 5.0 / 4.0 generations - the same retention lock covers all three SDS generations. Used on Phonak Audéo Infinio Ultra / Sphere Infinio, Lumity (including Life/Slim), Paradise, and Marvel, and matching Unitron RIC devices fitted for severe-to-profound hearing loss.
Show all compatible models
Phonak Audéo Infinio Ultra & Sphere Infinio with P receivers (current ranges)
Phonak Audéo Lumity (including Life/Slim), Paradise, and Marvel with P receivers (SDS 4.0 / 5.0)
Phonak Naída / Bolero / Sky Power BTE variants with P receivers
Unitron Moxi Vivante / Blu / Discover Next with P receivers
Costco Kirkland Signature KS9 / KS10 and Specsavers Advance Phonak-platform RICs with P receivers
Note: P (Power) is for severe-to-profound hearing loss fittings - the receiver body is physically larger than S or M to deliver more output. The S/M/P letter is printed on the receiver tip where the dome attaches.
You’re here
Medium (M) If your receiver tip shows a small "M", you need a different size.

Fits Medium power receivers across SDS 6.0 / 5.0 / 4.0 - moderate to severe hearing loss fittings.
Show all compatible models
Same Phonak / Unitron platform compatibility as Power, but specifically for receivers marked "M". The Medium retention lock is sized for a smaller receiver body than Power.
View Medium (M) →
Standard (S) If your receiver tip shows a small "S", you need a different size.

Fits Standard power receivers across SDS 6.0 / 5.0 / 4.0 - mild to moderate hearing loss fittings.
Show all compatible models
Same Phonak / Unitron platform compatibility as Power, but specifically for receivers marked "S". The Standard retention lock is sized for the smallest receiver body.
View Standard (S) →
Quick check: Look at the very tip of your receiver wire (the part that goes in your ear, where the dome attaches). There will be a small letter printed on it: S, M, or P. This is what determines retention lock size. The number prefix (00 / 0 / 1 / 2 / 3) is the receiver length and is not relevant for retention lock selection.

Important: If you're not sure, message us your hearing aid model or send a photo of the receiver tip - we'll confirm before you buy. Hygiene products can't be returned once opened, so please double-check before opening the pack.
✗ Not suitable for
  • Phonak / Unitron hearing aids with S or M receivers - use the Standard or Medium retention lock listings instead (see above)
  • Older Phonak / Unitron xReceiver wires (2-pin connector, pre-2019 - Audéo Q / V / B and equivalent) - need a different retention lock product designed for the older receiver shape
  • Phonak Audéo Fit M Sensor receivers (8-pin connector, Audéo L-R Fit and P-R Fit) - need a different retention product, made by Phonak for the M Sensor receiver
  • Non-Sonova brands (Oticon, Bernafon, Widex, GN ReSound, Beltone, Starkey, Signia, Rexton) - these use their own manufacturer-specific retention systems
  • Any hearing aid where the receiver tip doesn't carry a printed S / M / P size designation
Not sure of your receiver size? See Need more support? below - tell us your hearing aid model or send a photo of the receiver tip, and we'll confirm before you buy.

A retention lock slides onto the end of the receiver wire (just behind where the dome sits). It then loops gently into the bowl of your ear (the concha) to anchor the hearing aid in place. Fitting takes about a minute.

  1. Wash and dry your hands before handling the hearing aid.
  2. Remove the dome from the receiver tip (the small silicone or vented cap that sits in your ear canal). Set it aside.
  3. Slide the retention lock onto the receiver, just behind the receiver tip. The lock has a small ring or sleeve at one end that grips the receiver body; the long flexible arm extends out and curls into the ear.
  4. Refit the dome back onto the receiver tip. The retention lock should sit between the receiver body and the dome, holding firm.
  5. Pre-shape the arm if needed - if the lock is too straight or the wrong angle for your ear, you can curve it gently by sliding it over a smooth firm edge (the spine of a hardback book works well). This breaks the plastic memory just enough to take the new shape.
  6. Insert the hearing aid into your ear normally. The retention arm should tuck into the bowl of your ear - not pressing painfully, just resting against the concha to stop the aid sliding out.
  7. Adjust if needed - if the lock feels too long, too short, or rubs uncomfortably, remove it and re-shape. Each retention lock is reusable until it loses its spring or breaks.

Cold tip: If the locks feel stiff out of the pack (especially in cold weather), warm them in a pocket or near a radiator for 10 minutes before fitting. The plastic becomes more pliable and easier to shape.

Retention locks are reusable - they don't have a fixed replacement schedule like wax filters. Most users get 6-12 months from a single lock before the plastic loses its spring or starts to crack.

Replace your retention lock when you notice:

  • The arm has lost its shape and no longer holds against the concha.
  • The lock feels loose on the receiver body and slides off.
  • The plastic has visible cracks, splits, or stress marks.
  • The hearing aid feels less secure than it used to even after re-shaping.

Care tips:

  • Wipe gently with a soft dry cloth - don't soak or use solvents.
  • Replace the lock if you remove the receiver wire (e.g. when it's swapped or repaired) - getting a fresh lock onto a new receiver is easier than transferring an old one.
  • A pack of 10 typically lasts 5-10 years for a regular wearer with both aids fitted, depending on activity level and wear conditions.

Active wearers (sport, outdoor work) may go through locks faster as the plastic flexes more often. If you're particularly active, our pack of 10 gives you spares without committing to bulk packs.

  • 10 individual retention locks (Power / P size)
  • Sealed Phonak-branded packaging

Storage tip: Keep the unused locks in their original packaging at room temperature. Cold storage can stiffen the plastic and make pre-shaping harder.

Each lock fits one hearing aid - so a pair of hearing aids uses two locks at a time. With normal wear, a pack of 10 covers about 5 years of replacements for most users.

Are these genuine Phonak?
Yes. These are official Phonak-branded retention locks, sourced through authorised channels.

How do I know if I need Standard, Medium, or Power?
Look at the very tip of your receiver wire (where the dome attaches). There will be a small letter printed on it: S = Standard, M = Medium, P = Power. The letter matches your hearing loss fitting - it was set by your audiologist when the aid was prescribed. Match it exactly. If you can't see a letter at all, the receiver may be older xReceiver style (pre-2019) and need a different retention lock product.

Will this fit my Phonak Audéo Infinio Ultra or Sphere Infinio (SDS 6.0)?
Yes - if your receiver is marked S. Phonak uses the same retention lock parts across SDS 4.0, 5.0, and 6.0 generations. The part is sized by receiver power (S/M/P), not by SDS generation.

Will this fit my older Phonak Marvel / Paradise / Lumity (SDS 4.0 or 5.0)?
Yes - if your receiver is marked S. The same retention lock fits all three SDS generations. What matters is the size letter on the receiver, not the platform.

Will this fit Unitron hearing aids?
Yes. Unitron and Phonak share the Sonova receiver platform - the same retention locks fit Unitron Moxi Vivante, Blu, Discover Next, and Discover devices. Check for the S/M/P letter on the receiver tip.

Will this fit older Phonak xReceiver aids (Audéo Q / V / B)?
No. Older xReceiver wires (2-pin connector, pre-2019) have a different physical shape and need a different retention lock product. Tell us your hearing aid model and we'll point you to the right one.

Can I shape it to my ear?
Yes. The retention arm is pre-shapeable - slide it gently over a smooth, firm edge (the spine of a hardback book works well) to curve it before fitting. If it's stiff, warm it in a pocket for 10 minutes first. The plastic holds its new shape but you can re-shape if needed.

How often do I need to replace them?
Retention locks last 6-12 months for most users before the plastic loses spring or cracks. They're not single-use like wax filters - the pack of 10 typically covers 5+ years of replacements.

What information do you need from me?
Your hearing aid make and model (for example, "Phonak Audéo Infinio Ultra I90-R" or "Unitron Moxi Vivante 9"), and the receiver size letter if you can see it. A photo of the receiver tip works just as well.

Can I use these on Oticon, Widex, GN ReSound, or other brands?
No. These are Sonova-specific retention locks, designed to fit Phonak and Unitron receivers only. Other brands have their own retention systems with different shapes - check the manufacturer's accessory range.

What warranty covers this accessory?
Whatever the manufacturer's position, you are covered twice with us: our 30-day returns policy, and your statutory consumer rights, which run against us as the retailer. Phonak's manufacturer warranty covers the hearing aid itself and explicitly does not extend to consumable accessories such as receivers, tubes, and domes - so the protection that matters for this item is ours, above.

Buying with confidence
✓Genuine PhonakSourced from official channels
⇢Trusted DeliveryTracked and protected
↻30-Day ReturnsEasy returns on unopened packs
♥Audiologist-ledContact our team for assistance
Need more support?
Not sure of your hearing aid model or receiver size? Tell us your Phonak or Unitron model, or send a photo of the receiver tip - we'll confirm the correct size before you buy.

Phonak and SDS (Sound Delivery System) are trademarks of Sonova AG.
EarX is an independent retailer. The products we supply are genuine Phonak, sourced through authorised channels.