PRODUCT DESCRIPTION

DSPIAE · Scribing Tools

GS Tungsten Steel Gap Scraper – Dual Width

Two blade widths on every tool for cleaning seams, gaps and panel lines – five sizes, choose yours above 🪛

⭐ Why modellers use them

✅ Two widths in one tool – a narrow blade for fine lines and tight spots, and a wider one for clearing bigger seams and joints faster.

✅ Cleans out what other tools cannot reach – dried glue, paint, primer and filler sitting in the gaps between parts and in recessed lines.

✅ Restores crisp panel lines – reopens lines that have softened or filled up under putty, sanding or thick paint.

✅ Tungsten steel – hard, wear-resistant and holds its edge through a lot of scraping.

✅ Standard 3.175mm shank – fits handles and pin vices that accept a 1/8 inch shank.

🔧 What a gap scraper does

Seams, joints and panel lines collect everything a build throws at them: squeezed-out glue, sanding dust, filler, primer and paint. Over time they lose their crisp edges, and a panel wash no longer flows along them cleanly.

A gap scraper is made to put that right. Drawn along a seam or line, its square-edged tungsten blade scrapes away the build-up and the excess material, leaving a clean, even channel. It is equally useful for tidying a joint between two parts, cleaning out the separation lines on armour plates, and sharpening up a panel line that has gone soft.

Each GS scraper has two blade widths, so you can work the fine detail and the wider gaps of the same area without changing tools.

📏 Choose your size

Blade widths	Code	Typical use
0.2mm / 1.5mm	GS-0215	The widest spread: very fine lines plus large joints and structural seams
0.3mm / 0.6mm	GS-0306	Fine detailing and slightly wider seam lines
0.4mm / 0.8mm	GS-0408	Medium seams and gaps, an all-round size
0.5mm / 1.0mm	GS-0510	Medium to wide seams and joints
0.7mm / 1.4mm	GS-0714	Wide seams, structural gaps and larger mould lines

Match the blade to the gap: it should fit the channel snugly without forcing it wider. If you are unsure, the 0.4/0.8mm is the most versatile starting point.

📐 Specifications

Brand	DSPIAE
Series	GS gap scraper
Type	Dual-width seam and gap scraper bit
Material	Tungsten steel
Sizes	0.2/1.5 · 0.3/0.6 · 0.4/0.8 · 0.5/1.0 · 0.7/1.4mm
Shank diameter	3.175mm (1/8 inch)
Fits	Hobby tool handles and pin vices that accept a 3.175mm shank
For use on	Plastic, resin and similar modelling materials

📦 What you receive

▪️ 1 x DSPIAE GS tungsten steel gap scraper in the size you select

Handle not included. Each listing variation is a single scraper – select further sizes separately and the postage is combined.

💡 Tips for best results

👉 Scrape, do not dig. Draw the blade along the line with light pressure and let the edge shave the material away. Several gentle passes beat one heavy one.

👉 Pick the blade that fits. Use the width that sits in the gap snugly. A blade wider than the gap will cut into its edges and widen it.

👉 Clean up before painting. Run the scraper through seams and panel lines after filling and sanding, so primer goes onto clean, crisp detail.

👉 Rescue a filled-in line. After a heavy primer or paint coat, a light pass reopens panel lines so washes flow along them again.

👉 Keep it steady near edges. Rest your hand on the work or the bench to stop the blade skipping out of the gap onto the surface.

👉 Brush out the debris. Clear the scrapings between passes so you can see what is left to remove.

⚠️ Worth knowing before you buy

▪️ The handle is not included. These are bits with a 3.175mm (1/8 inch) shank. You need a handle or pin vice that accepts that size. Some small pin vices do not open wide enough, so check yours before ordering.

▪️ It is a cleaning and refining tool. A gap scraper is made for clearing and tidying existing seams, gaps and lines. For cutting brand-new panel lines and slots, a scriber or push broach is the better tool.

▪️ Tungsten steel is hard but brittle. It keeps its edge for a long time, but the blade can chip or snap if levered, twisted or dropped. Use it in a straight line with light pressure.

▪️ It scrapes paint off too. Used on a finished model it will remove paint from the line as well as the build-up. Work carefully on painted parts.

▪️ Sharp edges. Store with the tip protected and keep out of reach of children.

🚚 Dispatch and delivery

📮 Orders placed before 3 PM on working days are dispatched the same day.

🇬🇧 Sent from our own stock in Derby, UK – no waiting for overseas shipping.

📦 Buying several sizes or other items? Postage is combined, and if you end up overpaying we refund the difference when we pack your order.

Hobby Heaven

By Hobbyists. For Hobbyists.

A family-run UK hobby and art supplies shop. Not sure which size suits your seams? Send us a message – a real modeller will answer.

DSPIAE · Scribing Tools GS Tungsten Steel Gap Scraper – Dual Width Two blade widths on every tool for cleaning seams, gaps and panel lines – five sizes, choose yours above 🪛 ⭐ Why modellers use them ✅ Two widths in one tool – a narrow blade for fine lines and tight spots, and a wider one for clearing bigger seams and joints faster. ✅ Cleans out what other tools cannot reach – dried glue, paint, primer and filler sitting in the gaps between parts and in recessed lines. ✅ Restores crisp panel lines – reopens lines that have softened or filled up under putty, sanding or thick paint. ✅ Tungsten steel – hard, wear-resistant and holds its edge through a lot of scraping. ✅ Standard 3.175mm shank – fits handles and pin vices that accept a 1/8 inch shank. 🔧 What a gap scraper does Seams, joints and panel lines collect everything a build throws at them: squeezed-out glue, sanding dust, filler, primer and paint. Over time they lose their crisp edges, and a panel wash no longer flows along them cleanly. A gap scraper is made to put that right. Drawn along a seam or line, its square-edged tungsten blade scrapes away the build-up and the excess material, leaving a clean, even channel. It is equally useful for tidying a joint between two parts, cleaning out the separation lines on armour plates, and sharpening up a panel line that has gone soft. Each GS scraper has two blade widths, so you can work the fine detail and the wider gaps of the same area without changing tools. 📏 Choose your size Blade widths Code Typical use 0.2mm / 1.5mm GS-0215 The widest spread: very fine lines plus large joints and structural seams 0.3mm / 0.6mm GS-0306 Fine detailing and slightly wider seam lines 0.4mm / 0.8mm GS-0408 Medium seams and gaps, an all-round size 0.5mm / 1.0mm GS-0510 Medium to wide seams and joints 0.7mm / 1.4mm GS-0714 Wide seams, structural gaps and larger mould lines Match the blade to the gap: it should fit the channel snugly without forcing it wider. If you are unsure, the 0.4/0.8mm is the most versatile starting point. 📐 Specifications Brand DSPIAE Series GS gap scraper Type Dual-width seam and gap scraper bit Material Tungsten steel Sizes 0.2/1.5 · 0.3/0.6 · 0.4/0.8 · 0.5/1.0 · 0.7/1.4mm Shank diameter 3.175mm (1/8 inch) Fits Hobby tool handles and pin vices that accept a 3.175mm shank For use on Plastic, resin and similar modelling materials 📦 What you receive ▪️ 1 x DSPIAE GS tungsten steel gap scraper in the size you select Handle not included. Each listing variation is a single scraper – select further sizes separately and the postage is combined. 💡 Tips for best results 👉 Scrape, do not dig. Draw the blade along the line with light pressure and let the edge shave the material away. Several gentle passes beat one heavy one. 👉 Pick the blade that fits. Use the width that sits in the gap snugly. A blade wider than the gap will cut into its edges and widen it. 👉 Clean up before painting. Run the scraper through seams and panel lines after filling and sanding, so primer goes onto clean, crisp detail. 👉 Rescue a filled-in line. After a heavy primer or paint coat, a light pass reopens panel lines so washes flow along them again. 👉 Keep it steady near edges. Rest your hand on the work or the bench to stop the blade skipping out of the gap onto the surface. 👉 Brush out the debris. Clear the scrapings between passes so you can see what is left to remove. ⚠️ Worth knowing before you buy ▪️ The handle is not included. These are bits with a 3.175mm (1/8 inch) shank. You need a handle or pin vice that accepts that size. Some small pin vices do not open wide enough, so check yours before ordering. ▪️ It is a cleaning and refining tool. A gap scraper is made for clearing and tidying existing seams, gaps and lines. For cutting brand-new panel lines and slots, a scriber or push broach is the better tool. ▪️ Tungsten steel is hard but brittle. It keeps its edge for a long time, but the blade can chip or snap if levered, twisted or dropped. Use it in a straight line with light pressure. ▪️ It scrapes paint off too. Used on a finished model it will remove paint from the line as well as the build-up. Work carefully on painted parts. ▪️ Sharp edges. Store with the tip protected and keep out of reach of children. 🚚 Dispatch and delivery 📮 Orders placed before 3 PM on working days are dispatched the same day. 🇬🇧 Sent from our own stock in Derby, UK – no waiting for overseas shipping. 📦 Buying several sizes or other items? Postage is combined, and if you end up overpaying we refund the difference when we pack your order. Hobby Heaven By Hobbyists. For Hobbyists. A family-run UK hobby and art supplies shop. Not sure which size suits your seams? Send us a message – a real modeller will answer.

Specifications

Choose Products GS-0215 Gap scraper 0.2/1.5
Brand DSPIAE
Type Gap Scraper / Scribing Tool
Country/Region of Manufacture China
Suitable For Plastic Model Kits, Gunpla, Resin
Shank Diameter 3.175 mm

ABOUT US

Welcome to Hobby Heaven!

We're a brand built by passionate hobbyists for hobbyists. Our mission is to support all your creative endeavors, whether you're into modeling, wargaming, crafting, or art. As enthusiasts ourselves, we understand the importance of quality supplies at affordable prices.

Our carefully curated selection of high-quality materials is designed to inspire and empower hobbyists and artists alike. We're particularly proud of our innovative, cost-effective basing system - a game-changer for modelers and wargamers looking for professional results without breaking the bank.

At Hobby Heaven, we're dedicated to providing exceptional customer service and ensuring your creative projects are a success. Our team is always ready to offer advice, share techniques, or help you find the perfect supplies for your next masterpiece.

Thank you for choosing us as your trusted partner in creativity. We're excited to be part of your hobby journey!

PAYMENT

We accept payment by PayPal and Credit / Debit cards entered on eBay only. You must be registered with PayPal or eBay to buy from us.

SHIPPING

We primarily use RM24 for shipping, and we can arrange other courier services upon request. For large international shipments, we utilize FedEx. Once your order has been dispatched, you will receive tracking information. For domestic deliveries, the estimated arrival time is usually 1-4 days.

RETURNS

Please ensure that all items are returned in their original condition. Returns are processed within 1-2 business days of receipt. Refunds are issued minus the original shipping cost. All returns are handled in accordance with eBay's policies.

At Hobby Heaven, we strive to provide our customers with the best possible online shopping experience. Our commitment to excellent customer service extends well beyond the delivery of your order.

We encourage you to reach out with any questions or concerns regarding your purchase. The most convenient way to contact us is through the eBay messaging system.

Our dedicated customer service team responds to messages within 24 hours, Monday through Friday, between 8:00 AM and 3:00 PM GMT.

Your satisfaction is our top priority. We're here to help and look forward to assisting you!

WHAT OUR CUSTOMERS ARE SAYING ABOUT US

Order delivered on time with no issues	spruetwo (244 )
Order delivered on time with no issues	julma8824 (1 )
Order delivered on time with no issues	crad47 (412 )
Item received. Thanks.	handofganesh (228 )
Order delivered on time with no issues	hariali (168 )