Store Categories
Holybro PM02D Power Module High Voltage 2-12S for Pixhawk 5X/6X FlightController
Product Description
Note
PM02D HV version is supported by PX4. For Ardupilot, it is supported in Ardupilot latest/master FW, or version 4.4 and later.
This PM uses I2C digital signal data output and is not compatible with flight controller that uses analog PM such as the Pixhawk 6C & Mini, Pixhawk4 & Mini, pix32 v5, or Durandal flight controllers.
PM02D provides regulated power supply for your Pixhawk® 5X & 6X from the battery, as well as current consumption and battery voltage measurements, all through a 6pin cable. The on-board switching regulator outputs 5.2V and a maximum of 3A from LiPo batteries up to 6S (LV) or 12S (HV). The Power Module comes completely assembled with XT60 connectors, wrapped in shrink tubing for physical damage protection.
It is not designed to power servos, please use your aircraft's ESC/BEC for that. The Molex 2.00mm pitch CLIK-Mate Wire-to-Board connector is rated for 3.0A current per contact.
Specification
Input voltage
HV: 2S-12S
PCB Cont. Current Rating: 60A
PCB Burst Current Rating: 100A (<60 Sec)
Max current sensing: HV: 327A
Voltage and current monitor with I2C compatible interface
Outputs 5.2V and 3A max
Weight: 20g
Current Rating
The PM02D comes with XT60 plugs with 14 AWG silicone wires rated for 30A continuous current and 60A burst current (<1 minute). If a higher current is needed, the plug type and wire size should be changed accordingly. You can refer to this chart as reference.
PX4 Parameter Setup
If you are using the PM02D HV version, you must set SENS_EN_INA228 to enable.
Packing List
1 x PM02D Power Module
1 x 6Pin 2.00mm Pitch Cable
PM02D HV version is supported by PX4. For Ardupilot, it is supported in Ardupilot latest/master FW, or version 4.4 and later.
This PM uses I2C digital signal data output and is not compatible with flight controller that uses analog PM such as the Pixhawk 6C & Mini, Pixhawk4 & Mini, pix32 v5, or Durandal flight controllers.
PM02D provides regulated power supply for your Pixhawk® 5X & 6X from the battery, as well as current consumption and battery voltage measurements, all through a 6pin cable. The on-board switching regulator outputs 5.2V and a maximum of 3A from LiPo batteries up to 6S (LV) or 12S (HV). The Power Module comes completely assembled with XT60 connectors, wrapped in shrink tubing for physical damage protection.
It is not designed to power servos, please use your aircraft's ESC/BEC for that. The Molex 2.00mm pitch CLIK-Mate Wire-to-Board connector is rated for 3.0A current per contact.
Specification
Input voltage
HV: 2S-12S
PCB Cont. Current Rating: 60A
PCB Burst Current Rating: 100A (<60 Sec)
Max current sensing: HV: 327A
Voltage and current monitor with I2C compatible interface
Outputs 5.2V and 3A max
Weight: 20g
Current Rating
The PM02D comes with XT60 plugs with 14 AWG silicone wires rated for 30A continuous current and 60A burst current (<1 minute). If a higher current is needed, the plug type and wire size should be changed accordingly. You can refer to this chart as reference.
PX4 Parameter Setup
If you are using the PM02D HV version, you must set SENS_EN_INA228 to enable.
Packing List
1 x PM02D Power Module
1 x 6Pin 2.00mm Pitch Cable
We accept all verified payments from ebay.
Orders will be shipped after receiving cleared payment.
Payment due within 7 days after auction ends and for buy it now listings.
Orders will be shipped after receiving cleared payment.
Payment due within 7 days after auction ends and for buy it now listings.
1.We will ship based on the information provided by your order. Please ensure that the address and contact information are correct. If the delivery fails due to the buyer filling in incorrect information, our store will not be responsible.
2.If the delivery address is remote or in another country, it may take longer. Please be patient and wait.
3.Order placed on weekends or holiday will be handled and shipped on Monday or next working day.
4.If the item has not been delivered after the delivery time, please contact us promptly.
2.If the delivery address is remote or in another country, it may take longer. Please be patient and wait.
3.Order placed on weekends or holiday will be handled and shipped on Monday or next working day.
4.If the item has not been delivered after the delivery time, please contact us promptly.
1.If there are quality or usage issues with the purchased items, you can contact the store to solve the problem. We will try our best to help solve the problem as quickly as possible. Please do not leave negative feedback directly.
Our office hours are :
- 9:30 a.m. to 6:00 p.m. (GMT +8) of Monday to Friday
- Our office is closed on public holidays (China). We apologize for the late reply during the holidays.
We have always been trying to provide the best service and reliable products for every customer. Please contact us to resolve any issue before leaving negative feedback . we will assist you in any way possible and aim to answer all emails .
- 9:30 a.m. to 6:00 p.m. (GMT +8) of Monday to Friday
- Our office is closed on public holidays (China). We apologize for the late reply during the holidays.
We have always been trying to provide the best service and reliable products for every customer. Please contact us to resolve any issue before leaving negative feedback . we will assist you in any way possible and aim to answer all emails .
1, Light reflection and different displays may cause the color of the item in the picture a little different from the real thing.
Copyright © 2023 Dianxiaomi