eBay

PRODUCT DESCRIPTION

DSPIAE | CFB-S01

Irregular Carbon Fibre Sanding Sticks

Three shaped ends, 1 mm thin — for the places nothing else will go.

⚠️ Sandpaper is not included — and it isn't pre-cut either

Because the ends are irregular, no ready-made paper exists to fit them. You lay a stick on a sheet of self-adhesive sandpaper, draw round it, cut along the line and stick it on. It takes a minute per stick per grit. That is the trade-off for having a shape nothing else can reach — and it means you want sheet sandpaper, not the pre-cut pads made for flat boards.

📌 The problem isn't sanding. It's reaching.

Every build has one. A seam running down into a channel two millimetres wide. A mould line at the base of a raised detail you cannot get a board alongside. The inside of a recess, a socket, the gap between two closely-spaced fins.

You know exactly how to sand it. You simply cannot get anything in there — so you end up picking at it with a folded scrap of wet-and-dry, which is slow, inconsistent, and usually rounds off something adjacent that you wanted left alone.

This set exists for those spots and nothing else.

📏 One millimetre thick — and still rigid

These sticks are 1 mm thick. For comparison, a typical acrylic sanding pad is 2.5 mm and a carbon fibre board is 2 mm. That difference is not cosmetic — it is the difference between a tool that fits into a gap and one that sits on top of it.

But thin only helps if it stays flat. A 1 mm strip of plastic or acrylic would bend under finger pressure and simply follow whatever shape you pressed it against, which achieves nothing except moving material around. Carbon fibre composite is stiff for its thickness in a way that no plastic is.

DSPIAE also infiltrate the carbon with epoxy, which does two things: it resists stretching and bending across the tool's whole working life, and it leaves the cut edges smooth rather than leaving exposed fibre that would be unpleasant to hold and could scratch the part.

🛠️ Three sticks, three different ends

All three sticks share the same 10 × 75 mm body. What changes is the profile of the working end — each is cut to a different irregular shape, so between them they present a range of edges, points and curves to work into different geometry.

The set contains CFB-01, CFB-02 and CFB-03, one of each. They form the first of three sets in DSPIAE's irregular range, which runs from CFB-01 through CFB-09 — so if a shape you need is not here, it very likely exists in one of the others.

📦 What's in the box

✔ 1 × CFB-01 carbon fibre sanding stick

✔ 1 × CFB-02 carbon fibre sanding stick

✔ 1 × CFB-03 carbon fibre sanding stick

✔ Grit identification sticker

✘ No sandpaper — sold separately, and cut to shape by you

📋 Fitting the sandpaper

1. Choose self-adhesive sandpaper in the grit you want.

2. Lay the stick on it and draw round the outline.

3. Cut along the line.

4. Peel the backing off and place it carefully on the stick.

5. Press it down flat — no bubbles, no wrinkles, particularly around the shaped end.

Worth doing properly. A wrinkle at the tip is exactly where the tool does its work, and it will leave a mark rather than remove one. The grit sticker supplied goes on the stick so you know afterwards what is on it — useful once you have several in different grits and they all look alike.

📑 Specifications

Brand	DSPIAE
Model	CFB-S01
Type	Irregular carbon fibre sanding sticks
Contents	CFB-01, CFB-02, CFB-03 — one of each
Material	Carbon fibre, epoxy infiltrated
Thickness	1 mm
Width × length	10 × 75 mm, ends vary
Edges	Epoxy sealed, smooth
Sandpaper	Not included

💡 Getting the best from them

Cut several at once. Trace and cut paper for all three sticks in one sitting, in the two or three grits you actually use. Doing it one at a time as you need it is what makes people leave tools like this in a drawer.

Keep the stick flat to the surface. The rigidity is what gives you a clean result. Tipping it onto a corner of the tip puts a groove where you wanted a flat.

Use the shape that fits, not the one nearest to hand. The whole point of three profiles is that one of them matches the geometry in front of you. Test-fit before you start sanding.

Label them. Once all three have paper on, they look identical from the handle end. The supplied grit sticker exists for exactly this reason.

Wet sanding is fine. Epoxy-infiltrated carbon fibre will not swell, warp or delaminate the way a wood or card-cored stick does.

⚖️ Honest limitations

You cut your own sandpaper, every time. No pre-cut paper exists for irregular shapes and it is not going to. Budget a minute per stick per grit.

10 mm is narrow. These are precision access tools. On an open panel they will take all evening — a flat board does that job far faster.

Three specific shapes. If none of them matches the geometry you are fighting, sets 2 and 3 in the range carry six further profiles.

Pre-cut pads will not fit. The die-cut self-adhesive pads made for flat sanding boards are the wrong shape entirely. Buy sheet sandpaper for these.

🚚 Dispatch & delivery

✅ Same-day dispatch on orders placed before 3 PM, Monday to Friday

✅ Sent by Royal Mail 24 Tracked from our unit in Derby — full tracking from our door to yours, no import charges and no customs delays

✅ Packed properly. Tools travel in protective packaging, not a bare envelope

✅ Not sure whether one of these shapes will reach the spot you are stuck on? Message us and describe it — we build models ourselves and we will give you a straight answer

Hobby Heaven

By Hobbyists. For Hobbyists.

A family-run UK model and miniature supplier. We use the tools we sell, and we will tell you when something is not right for the job you have described.

DSPIAE | CFB-S01 Irregular Carbon Fibre Sanding Sticks Three shaped ends, 1 mm thin — for the places nothing else will go. ⚠️ Sandpaper is not included — and it isn't pre-cut either Because the ends are irregular, no ready-made paper exists to fit them. You lay a stick on a sheet of self-adhesive sandpaper, draw round it, cut along the line and stick it on. It takes a minute per stick per grit. That is the trade-off for having a shape nothing else can reach — and it means you want sheet sandpaper, not the pre-cut pads made for flat boards. 📌 The problem isn't sanding. It's reaching. Every build has one. A seam running down into a channel two millimetres wide. A mould line at the base of a raised detail you cannot get a board alongside. The inside of a recess, a socket, the gap between two closely-spaced fins. You know exactly how to sand it. You simply cannot get anything in there — so you end up picking at it with a folded scrap of wet-and-dry, which is slow, inconsistent, and usually rounds off something adjacent that you wanted left alone. This set exists for those spots and nothing else. 📏 One millimetre thick — and still rigid These sticks are 1 mm thick. For comparison, a typical acrylic sanding pad is 2.5 mm and a carbon fibre board is 2 mm. That difference is not cosmetic — it is the difference between a tool that fits into a gap and one that sits on top of it. But thin only helps if it stays flat. A 1 mm strip of plastic or acrylic would bend under finger pressure and simply follow whatever shape you pressed it against, which achieves nothing except moving material around. Carbon fibre composite is stiff for its thickness in a way that no plastic is. DSPIAE also infiltrate the carbon with epoxy, which does two things: it resists stretching and bending across the tool's whole working life, and it leaves the cut edges smooth rather than leaving exposed fibre that would be unpleasant to hold and could scratch the part. 🛠️ Three sticks, three different ends All three sticks share the same 10 × 75 mm body. What changes is the profile of the working end — each is cut to a different irregular shape, so between them they present a range of edges, points and curves to work into different geometry. The set contains CFB-01, CFB-02 and CFB-03, one of each. They form the first of three sets in DSPIAE's irregular range, which runs from CFB-01 through CFB-09 — so if a shape you need is not here, it very likely exists in one of the others. 📦 What's in the box ✔ 1 × CFB-01 carbon fibre sanding stick ✔ 1 × CFB-02 carbon fibre sanding stick ✔ 1 × CFB-03 carbon fibre sanding stick ✔ Grit identification sticker ✘ No sandpaper — sold separately, and cut to shape by you 📋 Fitting the sandpaper 1. Choose self-adhesive sandpaper in the grit you want. 2. Lay the stick on it and draw round the outline. 3. Cut along the line. 4. Peel the backing off and place it carefully on the stick. 5. Press it down flat — no bubbles, no wrinkles, particularly around the shaped end. Worth doing properly. A wrinkle at the tip is exactly where the tool does its work, and it will leave a mark rather than remove one. The grit sticker supplied goes on the stick so you know afterwards what is on it — useful once you have several in different grits and they all look alike. 📑 Specifications BrandDSPIAE ModelCFB-S01 TypeIrregular carbon fibre sanding sticks ContentsCFB-01, CFB-02, CFB-03 — one of each MaterialCarbon fibre, epoxy infiltrated Thickness1 mm Width × length10 × 75 mm, ends vary EdgesEpoxy sealed, smooth SandpaperNot included 💡 Getting the best from them Cut several at once. Trace and cut paper for all three sticks in one sitting, in the two or three grits you actually use. Doing it one at a time as you need it is what makes people leave tools like this in a drawer. Keep the stick flat to the surface. The rigidity is what gives you a clean result. Tipping it onto a corner of the tip puts a groove where you wanted a flat. Use the shape that fits, not the one nearest to hand. The whole point of three profiles is that one of them matches the geometry in front of you. Test-fit before you start sanding. Label them. Once all three have paper on, they look identical from the handle end. The supplied grit sticker exists for exactly this reason. Wet sanding is fine. Epoxy-infiltrated carbon fibre will not swell, warp or delaminate the way a wood or card-cored stick does. ⚖️ Honest limitations You cut your own sandpaper, every time. No pre-cut paper exists for irregular shapes and it is not going to. Budget a minute per stick per grit. 10 mm is narrow. These are precision access tools. On an open panel they will take all evening — a flat board does that job far faster. Three specific shapes. If none of them matches the geometry you are fighting, sets 2 and 3 in the range carry six further profiles. Pre-cut pads will not fit. The die-cut self-adhesive pads made for flat sanding boards are the wrong shape entirely. Buy sheet sandpaper for these. 🚚 Dispatch & delivery ✅ Same-day dispatch on orders placed before 3 PM, Monday to Friday ✅ Sent by Royal Mail 24 Tracked from our unit in Derby — full tracking from our door to yours, no import charges and no customs delays ✅ Packed properly. Tools travel in protective packaging, not a bare envelope ✅ Not sure whether one of these shapes will reach the spot you are stuck on? Message us and describe it — we build models ourselves and we will give you a straight answer Hobby Heaven By Hobbyists. For Hobbyists. A family-run UK model and miniature supplier. We use the tools we sell, and we will tell you when something is not right for the job you have described.

Specifications

Brand Dspiae
Type Sanding Stick Set
Number of Pieces 3
Grit 200
MPN PT-SP02
Suitable For Scale Models, Gunpla, Miniatures, Airbrushing, Acrylic/Lacquer/En
Country of Origin China
Colour Red / Black

ABOUT US

Welcome to Hobby Heaven!

We're a brand built by passionate hobbyists for hobbyists. Our mission is to support all your creative endeavors, whether you're into modeling, wargaming, crafting, or art. As enthusiasts ourselves, we understand the importance of quality supplies at affordable prices.

Our carefully curated selection of high-quality materials is designed to inspire and empower hobbyists and artists alike. We're particularly proud of our innovative, cost-effective basing system - a game-changer for modelers and wargamers looking for professional results without breaking the bank.

At Hobby Heaven, we're dedicated to providing exceptional customer service and ensuring your creative projects are a success. Our team is always ready to offer advice, share techniques, or help you find the perfect supplies for your next masterpiece.

Thank you for choosing us as your trusted partner in creativity. We're excited to be part of your hobby journey!

PAYMENT

We accept payment by PayPal and Credit / Debit cards entered on eBay only. You must be registered with PayPal or eBay to buy from us.

SHIPPING

We primarily use RM24 for shipping, and we can arrange other courier services upon request. For large international shipments, we utilize FedEx. Once your order has been dispatched, you will receive tracking information. For domestic deliveries, the estimated arrival time is usually 1-4 days.

RETURNS

Please ensure that all items are returned in their original condition. Returns are processed within 1-2 business days of receipt. Refunds are issued minus the original shipping cost. All returns are handled in accordance with eBay's policies.

At Hobby Heaven, we strive to provide our customers with the best possible online shopping experience. Our commitment to excellent customer service extends well beyond the delivery of your order.

We encourage you to reach out with any questions or concerns regarding your purchase. The most convenient way to contact us is through the eBay messaging system.

Our dedicated customer service team responds to messages within 24 hours, Monday through Friday, between 8:00 AM and 3:00 PM GMT.

Your satisfaction is our top priority. We're here to help and look forward to assisting you!

WHAT OUR CUSTOMERS ARE SAYING ABOUT US

Order delivered on time with no issues	smigg-the-mi (92 )
Order delivered on time with no issues	smigg-the-mi (92 )
Order delivered on time with no issues	smigg-the-mi (92 )
Order delivered on time with no issues	hariali (168 )
Order delivered on time with no issues	hariali (168 )