Same-day 1st class shipping: Monday - Friday by 3.30PM (GMT-0).

PRODUCT DESCRIPTION

N42 Neodymium Disc Magnets — 5 x 1 mm
Nickel-Copper-Nickel coated • Axially magnetised • Packs of 1, 10, 25, 50 and 100
Our strongest shallow disc. 220 g of pull from a 1.2 mm recess — more than a 3 x 2 mm magnet gives, at half the depth.
Why this size
✓ Serious hold, almost no depth. 220 g from 1.2 mm of recess. Nothing else in the range gives you that much for that little material removed.
✓ Calculated pull: 220 g at direct contact. Zero gap, clean flat steel. Magnet-to-magnet also 220 g. Reference value, not a guaranteed working load.
✓ Fits where a thicker magnet cannot. A standard round miniature base, a thin styrene panel, a laser-cut MDF terrain piece — all places where a 2 mm disc would break through or stand proud.
✓ Spreads its grip. A wide, flat disc resists tilting far better than a narrow one, so a magnetised panel sits down evenly instead of rocking on one edge.
✓ Honest N42 grade. We state the grade we actually buy. If you see the same disc advertised as N52 at this size, treat the claim with caution.
What it is

A sintered neodymium (NdFeB) disc, 5 mm across and 1 mm thick, magnetised through its thickness — the poles are the two flat faces, not the edge. Two magnets meet face to face, the join sits flat, and the part seats in the same position every time.

This is the clearest demonstration in our range of how neodymium actually behaves. Holding force follows the area of the pole face far more than it follows how tall the magnet is. Widen a disc and you gain a lot; heighten it and you gain steadily less. A 5 mm disc only 1 mm tall out-pulls a 3 mm disc twice its height, using half the depth in the part.

That makes it the natural choice wherever material is the constraint rather than surface area — thin walls, shallow bases, flat panels and anything you would rather glue onto than drill into.

Specifications
Diameter 5 mm
Thickness 1 mm
Weight per magnet 0.15 g
Material Sintered neodymium iron boron (NdFeB)
Grade N42
Coating Nickel-Copper-Nickel (NiCuNi), triple layer
Magnetisation Axial — poles on the flat faces
Pull to steel (calculated) 220 g / 2.16 N at direct contact, zero gap
Magnet-to-magnet pull 220 g, bare faces in direct contact
Shear (sideways) estimate Approximately 30 g — sideways load is far weaker than direct pull
Drill bit size 5 mm
3D print hole size 5.1 mm
Maximum working temperature Approximately 80°C — standard for N42
Country of manufacture China

Pull figures are calculated reference values for a clean, flat, direct steel contact with no air gap. Paint, primer, glue layers, curved surfaces and any gap at all will reduce holding force, in some cases substantially. Treat these numbers as a way to compare sizes to each other, not as a guaranteed working load.

What you get
▪ The pack size you select from the dropdown: 1, 10, 25, 50 or 100 magnets
▪ Supplied stacked pole-to-pole in a resealable bag
▪ Every magnet is the same 5 x 1 mm N42 disc — the only difference between variants is the count
What this size is for
Well suited to: thin round miniature bases where a thicker magnet would break through • removable hull decks, hatches and access panels on model kits • laser-cut MDF and card terrain • display bases and plinth mounts • craft closures on board, card and thin timber • any join you would rather glue onto than drill into.
Choose 5 x 2 mm instead when: the part has depth to spare and you want a much firmer hold — the same 5 mm hole, more than double the pull at 470 g. That is the size for magnetised bases and steel-lined transport trays.
Choose 4 x 1 mm instead when: a 5 mm disc is too wide for the part, or a 5 mm hole would leave too little material around it.
Working with them
Measure your base before you drill. Most standard round bases are only 2 to 3 mm thick, and a lot of that is the rim. A 1.2 mm recess leaves material behind it; a 2.2 mm one very often does not. If you are magnetising bases and want to keep the underside intact, this is the disc that fits.
You may not need to drill at all. On a hollow base or a closed panel, glue the magnet flat to the inside face. At 1 mm the standoff is small enough to disappear into a gap that was already there. Test-fit before the glue cures.
Thin magnets are easy to seat crooked. At 1 mm thick there is very little side wall to hold the disc square in a recess. Press it flat with the back of a hobby knife while the glue grabs — a magnet sitting at a slight angle loses contact area and holding force.
Mark the stack before you separate it. Put a dot of permanent marker on one face of the whole stack while it is still assembled. Every magnet then carries the same reference face. Reversing one magnet is the single most common way a magnetised part ends up pushing itself off.
Keep paint out of the joint. A coat of primer plus two of paint on both mating faces is easily 0.1 mm of gap, and that costs you real holding force. Mask the faces, or fit the magnets after painting.
Honest limitations
▪ It needs 5 mm of width. That is a wide hole on a small part, and a 5 mm bore through a 6 mm post leaves almost nothing behind. Width is the trade you make for the shallow depth.
▪ 220 g is a panel and base magnet, not a heavy-part magnet. Fine for styrene, resin and card. Not the size for a cast metal turret or a weighted display piece.
▪ Thin discs are fiddly. At 1 mm they are easy to lose, easy to seat crooked, and easy to pick up two at a time without noticing.
▪ Sideways load is much weaker than straight pull. Around 30 g. A panel that slides in its frame will move far more easily than one that lifts straight off.
▪ Neodymium is brittle. These are sintered, ceramic-like magnets, and wide thin discs are the easiest of all to crack. Letting a stack snap together from a distance can chip them.
▪ Indoor use. NiCuNi plating resists handling and normal indoor humidity, but it is not a marine or outdoor coating.
▪ Heat weakens them permanently. Above roughly 80°C an N42 magnet loses strength and does not recover on cooling. Keep them away from ovens, curing lamps and hot cars.
Important safety information

Warning — strong magnets. For adult hobby and technical use. Not a toy.

Swallowing two or more magnets can cause serious internal injury. Magnets can attract to each other through the wall of the intestine, causing blockage or perforation. Seek immediate medical attention if a magnet is swallowed or inhaled. Keep away from children and pets at all times.

Keep magnets away from pacemakers, implanted defibrillators and hearing aids. Keep them away from bank cards, hard drives and other magnetic media.

Handle with care — neodymium is brittle and can chip. Store magnets in their bag, away from loose steel and craft blades.

Dispatch
▪ Same-day dispatch on orders placed before 3 PM, Monday to Friday
▪ Sent from our own unit in Derby — we pick and pack everything ourselves
▪ Magnets are shipped within the UK only
Hobby Heaven
By Hobbyists. For Hobbyists.

We are a small family-run business in Derby, run by people who actually paint, build and convert. We publish the grade we buy and the test conditions behind every pull figure, because that is the information we wanted when we were sourcing magnets for our own projects. If something is not right, message us and we will sort it.

Specifications

  • Choose Quantity 10
  • Brand Hobby Heaven
  • Thickness 1mm
  • Type Disc Magnet
  • Shape Disc
  • Item Diameter 5mm
  • Grade N42
  • Coating Nickel-Copper-Nickel (NiCuNi)
  • Magnetisation Axial
  • Country of Origin China
  • Colour Silver

Welcome to Hobby Heaven!

We're a brand built by passionate hobbyists for hobbyists. Our mission is to support all your creative endeavors, whether you're into modeling, wargaming, crafting, or art. As enthusiasts ourselves, we understand the importance of quality supplies at affordable prices.

Our carefully curated selection of high-quality materials is designed to inspire and empower hobbyists and artists alike. We're particularly proud of our innovative, cost-effective basing system - a game-changer for modelers and wargamers looking for professional results without breaking the bank.

At Hobby Heaven, we're dedicated to providing exceptional customer service and ensuring your creative projects are a success. Our team is always ready to offer advice, share techniques, or help you find the perfect supplies for your next masterpiece.

 

Thank you for choosing us as your trusted partner in creativity. We're excited to be part of your hobby journey!

We accept payment by PayPal and Credit / Debit cards entered on eBay only. You must be registered with PayPal or eBay to buy from us.

 

We primarily use RM24 for shipping, and we can arrange other courier services upon request. For large international shipments, we utilize FedEx. Once your order has been dispatched, you will receive tracking information. For domestic deliveries, the estimated arrival time is usually 1-4 days.

Please ensure that all items are returned in their original condition. Returns are processed within 1-2 business days of receipt. Refunds are issued minus the original shipping cost. All returns are handled in accordance with eBay's policies.

At Hobby Heaven, we strive to provide our customers with the best possible online shopping experience. Our commitment to excellent customer service extends well beyond the delivery of your order.

We encourage you to reach out with any questions or concerns regarding your purchase. The most convenient way to contact us is through the eBay messaging system.

Our dedicated customer service team responds to messages within 24 hours, Monday through Friday, between 8:00 AM and 3:00 PM GMT.

 

Your satisfaction is our top priority. We're here to help and look forward to assisting you!

WHAT OUR CUSTOMERS ARE SAYING ABOUT US

Order delivered on time with no issues beano4435 (194 )
Order delivered on time with no issues julma8824 (1 )
Order delivered on time with no issues crad47 (412 )
Order delivered on time with no issues smigg-the-mi (92 )
Order delivered on time with no issues smigg-the-mi (92 )