Fix Tripping, No Heating, and Rod Failures – Upgraded Genuine Replacement
This brand new 220V 2kW Lay-Z-Spa Hydro Jet Heating Element is an upgraded part, specially designed for post-2021 four-pipe HydroJet models. It includes a full seal kit, an installation video, and reinforced internal clamps to prevent rod push-outs, a known failure in earlier units.
Are you suffering with black flakes entering your spas water? this is a sign that your element is corroding due to chemical imbalances. the coating from the tubes if compromised and the corrosion would have started. this can also cause rod push outs. THIS MODEL HAS NO BLACK COATING WHICH ELIMINATES THE BLACK FLAKE ISSUE.
220V | 2kW | 4-element design
Upgraded part with anti-push-out clamps for increased durability
Supplied with complete new seal kit
Includes step-by-step installation video
Genuine replacement for post-2021 4-pipe HydroJet models
Can be retrofitted to some older "egg-style" units – contact us to check fit
This heater assembly is designed for use only with the specific models listed below, and your unit must also have a visible reset button as shown in the product images.
Before purchasing, please check the data label located on the side of your pump unit to confirm compatibility. If you are unsure whether this part is suitable for your model, contact us and we’ll be happy to assist.
Compatible Models:
S200101 / S200102 / S200103 / S200104
S200201 / S200202 / S200203 / S200204
Electrical Rating:
220–240V AC | 50–60Hz
⚠️ Important: Although this heater may look similar to 110–120V versions, it is not electrically interchangeable. Using this part on the wrong voltage supply can cause serious damage to your equipment and may present a safety risk.
If you are in any doubt, please get in touch before ordering — we’re happy to help you confirm the correct part.
❌ Rod push out burning holes into outer case. Rods may still push out due to aggressive water imbalances. the new clamps just protect the out case from damage.
❌ RCD or fuse tripping
❌ Sudden shutoffs
❌ Rod push-outs (solved with upgraded clamp design)
Tripping or leaks? Internal corrosion or worn rods are common. This upgraded heater has reinforced clamps to prevent rod push-out, which can cause shorts, leaks, and total failure.
High copper levels (from algaecides) and aggressive water chemistry can lead to pitting and corrosion, which may void your warranty. Keep your spa water balanced and regularly tested.
Designed for confident DIYers, this heating element installs in under 30 minutes.
Tools Required:
Phillips screwdriver
Pliers
Marker for labeling wires
Installation steps:
Unplug the spa and remove the top cover.
Remove the circuit board cover.
Gently pull out the board for access and label the four wires (1–4).
Remove all screws on the heater front and rear plates.
Slide out the old element.
Install the new upgraded element with included seals.
Reattach the plates and wires.
Replace all covers and test the spa.
Installation video included with every purchase for guided help.
Plus, full support available if needed.
1x Upgraded Lay-Z-Spa Hydro Jet Heating Element (220V, 2kW, 4-element)
1x New Seal Kit (High Temperature Silicone)
1x Installation video access
After-sales support & guidance
✅ Fits:
All post-2021 four-pipe Lay-Z-Spa HydroJet models
May also fit older egg-shaped HydroJet units – contact us before purchase to confirm.
Fast dispatch
We stock only brand new, genuine, and upgraded Lay-Z-Spa parts, never pulled from old machines. This heater includes clamp reinforcements to avoid common rod push-out failures — a problem not addressed in standard replacements. Our goal is to help you fix your spa right the first time, with full support, fast shipping, and honest service.
Returns accepted within 30 days
Buyer pays return postage
If eBay prepaid return labels are used, the postage will be deducted from the refund
Item must be unused and in original packaging
Please confirm compatibility before ordering – contact for support.