Model
IX-1050
Main unit / expansion unit
Expansion unit
Display
Min. display unit
10 µm*1
Display range
±999.99 to ±999 mm (with 4 selectable steps)*1
Tools
Scan mode
Height, Height difference, Max./Min., Height difference calculation, Thickness calculation, Height detection, Monochromatic detection, Position adjustment
(Max. number of settings) Detection: 16 tools, Position adjustment: 1 tool*2
Line mode
Height (Ave./Max./Min.) , Height difference (Ave./Max./Min.) , Height difference calculation, Thickness calculation, Position adjustment, Tilt correction
(Max. number of settings) Detection: 16 tools, Position adjustment: 1 tool, Alignment adjustment: 1 tool*2
Other functions
Common
ZERO/offset, Operating threshold adjustment, 2-point calibration, Measurement direction, Position correction NG measurement,
Zero/offset recording,Capture mode (HDR) Sensor date/time Information addition, N.O./N.C. switching, I/O monitor,
Automatic brightness adjustment, Lighting (ON/OFF) , Total judgment conditions,NPN/PNP switching, Simultaneous main unit/expansion unit input, Light interference prevention, Security
Scan mode
Measurement range, Measurement position (small/standard/large) , Measurement mode, Measurement noise elimination,
Imaging mode (high gain) , Tilt correction (fixed or real-time correction) , Glare removal, Trigger input (internal/external) ,
Trigger interval, Trigger delay, Trigger error, Monochrome histogram, Fixed reference area, Mask outline, Rotation range
Line mode
Average count, Laser position adjustment, Timing input, Head tilt correction (fixed only), Ambient light removal for measurement, HOLD function, Alarm setting, Measurement method (Ave./Max./Min.)
Input
Input
Non-voltage input/voltage input is switchable
For non-voltage input: ON voltage 2 V or lower, OFF current 0.1 mA or lower, ON current 2 mA (short circuit)
For voltage input: Maximum input rating 26.4 V, ON voltage 18 V or higher, OFF current 0.2 mA or lower, ON current 2 mA (for 24 V)
Number of inputs
8 (IN1 to IN8)
Function
IN1: External trigger up/down timing, IN2 to IN8: Enable by assigning optional functions
Assignable functions: Program switching, Laser emission stop, Zero/offset (batch) , Reset (error only) , Reset (judgment value only) Reset (judgment value and error)
Output
Output
Open collector output; NPN/PNP switchable, N.O./N.C. switchable
For open collector NPN output: Maximum rating of 26.4 V, 50 mA (20 mA when linked to an expansion unit) , residual voltage of 1.5 V or less
For open collector PNP output: Maximum rating of 26.4 V, 50 mA (20 mA when linked to an expansion unit) , residual voltage of 2 V or less
Number of inputs
10 (OUT1 to OUT10)
Function
Enable by assigning the optional functions
Assignable functions: Total judgment result (All OK, Any OK/NG) , run, busy, error, position adjustment result, tilt correction result,
Monochromatic detection/Height detection tool result (OK/NG) , Height/height difference/Max./Min./calculation tool result (OK/NG/HIGH/LO) , Alarm
Number of programs
32
Statistical information
Scan mode: Measured value / Degree of similarity (Max., Min., Ave.), Processing time (Latest, Max., Min., Ave.), Count (Number of OKs / Number of NGs / Number of triggers)
Line mode: Measured value / Degree of similarity (Max., Min., Ave.), Count (Number of OKs / Number of NGs / Number of triggers)*1*3
Detection history
Saved history
100*4
Save conditions
Selectable from NG only / All*4
Ethernet
Standard
Not available
Connector
Interface compatibility
CC-Link / DeviceNet® / EtherNet/IP® / EtherCATⓇ / RS-232C / BCD / PROFINET / PROFIBUS / TCP/IP output*5
Number of connectible units
Main units: 1, Expansion units: 1, Communication units (DL) : 1
Ratings
Power voltage
Supplied from main unit
Current consumption
Max. 1.9 A or less (With main unit only: 0.8 A or less, With unit expansion: 1.9 A or less) (Excluding output load)*6
Environmental resistance
Ambient temperature
0 to +50°C 32 to 122°F (No freezing)
Relative humidity
35 to 85 % RH (No condensation)
Material
Main unit case: PC/Power connector: PA, POM/Analog output connector: PA, POM/I/O connector: PA/
Head connector: Zinc + Ni plating, PA/Ethernet connector: Copper alloy + Ni plating/
Rear heat sink: Aluminum/Main unit rear DIN rail fixing tab: POM/Nameplate: PC
Weight
Approx. 190 g