• Fits:
  • 1994-2001 ACURA INTEGRA  All Models
  • 1992-1995 HONDA CIVIC  All Models
  • 1993-1997 HONDA CIVIC DEL SOL  All Models
  •  
  •  
  • Kit Part Includes
  • 1 x Front Upper Control Arm And Ball Joint - Passenger Side - K90448
  •  
  •  
  • Replacement Guideline
  • Ball joints
  • For Acura Integra Honda Civic Front Upper Right Control Arm w/ Ball Joint K90448

    Fits:

    1994-2001 ACURA INTEGRA  All Models

    1992-1995 HONDA CIVIC  All Models

    1993-1997 HONDA CIVIC DEL SOL  All Models

     

     

    Kit Part Includes

    1 x Front Upper Control Arm And Ball Joint - Passenger Side - K90448

     

     

    Replacement Guideline

    Ball joints

    1. Purchase the correct replacement ball joint assembly for your vehicle.
    2. Remove the wheel and access the ball joint.
    3. Soak all the bolts with WD-40 or PB Blaster.
    4. Pull the cotter pin and loosen the large castellated nut.
    5. Pop loose the ball joint. 
    6. Remove the allen bolts and slide the control arm free. 
    7. Guide the new joint through the knuckle hole.
    8. Bolt the joint into place using the hardware included.
    9. Torque the bolts to the proper specifications.
    10. Screw in the new grease fitting and pump grease into the assembly.

    Control Arms

    1. lift the vehicle using a car lift, ideally a wheel-free four-post car lift
    2. loosen and remove the corresponding stabiliser fixing screws.
    3. Loosen the ball joint at the steering knuckle with a suitable special tool (e.g. a puller).
    4. Remove the old control arm
    5. Clean the mounting flange of the ball joint pin on the steering knuckle with sandpaper and then with brake cleaner
    6. Fit the new control arm with the supplied accessories and attach new fixing screws and nuts.
    7. Reattach the stabilizer and, if applicable, the leveling sensor for headlight leveling to the control arm.
    8. lower the vehicle until the suspension is compressed
    9. Tighten the fixing screws with the torque stipulated by the vehicle manufacturer.
    10. Lower the vehicle all the way.
    11. Measure the chassis and adjust if necessary.
    12. Check and, if necessary, adjust the headlight settings on vehicles with automatic headlight leveling where the leveling sensor is attached to the control arm.
    13. To conclude, test-drive the vehicle.

     

    Bad Control arm symptons

    • popping noise
    • steering is unstable
    • uneven tire wear

     

    Signs of a ball joint breaks

    • Sound -A faint, intermittent clunking noise that seems to be coming from a corner of your vehicle
    • Steering-The steering sloppy or stiff 
    • Tires -Uneven tire wear 

     

    Infiuence of a bad joint break

    • Causing mysterious clunking noise or drifting steering
    • Affecting your steering and suspension seriously 

     

    Importance of Control Arms

    • It is a link that connects the frame of the car to the wheel hub assembly or steering knuckle.
    • It allows a driver to steer a car while also guiding the wheels up and down with the road surface.
    • They have a vital role in a vehicle's overall stability and drivability.

     

    Note

    • Please be sure you review the compatibility information.
    • If you have a question about the part please free contact us before buying, we will give you a best reply in time.
    • We are galde to offer quality service and vehicle parts to you, any after sale questions please message us before open case or feedback, we will give you the best solution.

    Item Specifics
    Brand auspartshouse
    Manufacturer Part Number 13450916
    Interchange Part Number K90448
    OE/OEM Part Number 5145SR323
    Manufacturer Warranty 10 Year
    Universal Fitment No
    Kit or Single Part Single
    Adjustable Yes
    Quantity 1 Piece
    Items Included Mounting Hardware
    Store Speciality Suspension & Steering
    Placement on Vehicle Right Front Upper
    Kit Parts Included Control Arm, Ball Joint
    Surface Finish Polished, Rust Protected
    Fitment For Acura, Honda
    Type Control Arm & Ball Joint Assembly
    Control Arm Construction Stamped
    OE Spec or Performance/Custom OE Spec
    Modified Item No
    Material Steel
    Features Easy to Replace
    Cotter Pin Hole Yes
    Material Steel
    Mounting Style Bolt-On
    Finish Polished

    Payment:
    We use eBay's Safe and Secure Checkout. Just click the Pay Now button at the top of any of the auctions you have won.
     
    To pay for multiple auctions, successfully win all auctions you wish to purchase and then click the Pay Now button on any of the listings you won. You will only have to checkout and pay once for your entire order.
     
    Please review our detailed policies on shipping and fixing any issues before purchasing the item. If you have any questions, please email us through "Ask a question".
     
    Payment Options: Any payment which can be accepted by ebay.
     
    If you want to change the shipping address, please contact us by eBay messages within 12 hours.
     
    Payment must be received within 10 days as auction ended or order might be delayed.
    Shipping:

    2. We only ship to the address in order provided to us. Your order address will be the shipping address.

    4. If you have not received your shipment within 15 days from payment, please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!

    Returns:

    1. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.

    2. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.

    3. Return shipping is to be paid by the Buyer if the problem turned to be buyer's end, or return will be seller's responsibility.

    Feedback:

    We maintain high standards of excellence and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.

    Contact Us:

    Any question or problem, please feel free to contact us via ebay message.

    Shop Category

    For Acura Integra Honda Civic Front Upper Right Control Arm w/ Ball Joint K90448

    Fits:

    1994-2001 ACURA INTEGRA  All Models

    1992-1995 HONDA CIVIC  All Models

    1993-1997 HONDA CIVIC DEL SOL  All Models

     

     

    Kit Part Includes

    1 x Front Upper Control Arm And Ball Joint - Passenger Side - K90448

     

     

    Replacement Guideline

    Ball joints

    1. Purchase the correct replacement ball joint assembly for your vehicle.
    2. Remove the wheel and access the ball joint.
    3. Soak all the bolts with WD-40 or PB Blaster.
    4. Pull the cotter pin and loosen the large castellated nut.
    5. Pop loose the ball joint. 
    6. Remove the allen bolts and slide the control arm free. 
    7. Guide the new joint through the knuckle hole.
    8. Bolt the joint into place using the hardware included.
    9. Torque the bolts to the proper specifications.
    10. Screw in the new grease fitting and pump grease into the assembly.

    Control Arms

    1. lift the vehicle using a car lift, ideally a wheel-free four-post car lift
    2. loosen and remove the corresponding stabiliser fixing screws.
    3. Loosen the ball joint at the steering knuckle with a suitable special tool (e.g. a puller).
    4. Remove the old control arm
    5. Clean the mounting flange of the ball joint pin on the steering knuckle with sandpaper and then with brake cleaner
    6. Fit the new control arm with the supplied accessories and attach new fixing screws and nuts.
    7. Reattach the stabilizer and, if applicable, the leveling sensor for headlight leveling to the control arm.
    8. lower the vehicle until the suspension is compressed
    9. Tighten the fixing screws with the torque stipulated by the vehicle manufacturer.
    10. Lower the vehicle all the way.
    11. Measure the chassis and adjust if necessary.
    12. Check and, if necessary, adjust the headlight settings on vehicles with automatic headlight leveling where the leveling sensor is attached to the control arm.
    13. To conclude, test-drive the vehicle.

     

    Bad Control arm symptons

    • popping noise
    • steering is unstable
    • uneven tire wear

     

    Signs of a ball joint breaks

    • Sound -A faint, intermittent clunking noise that seems to be coming from a corner of your vehicle
    • Steering-The steering sloppy or stiff 
    • Tires -Uneven tire wear 

     

    Infiuence of a bad joint break

    • Causing mysterious clunking noise or drifting steering
    • Affecting your steering and suspension seriously 

     

    Importance of Control Arms

    • It is a link that connects the frame of the car to the wheel hub assembly or steering knuckle.
    • It allows a driver to steer a car while also guiding the wheels up and down with the road surface.
    • They have a vital role in a vehicle's overall stability and drivability.

     

    Note

    • Please be sure you review the compatibility information.
    • If you have a question about the part please free contact us before buying, we will give you a best reply in time.
    • We are galde to offer quality service and vehicle parts to you, any after sale questions please message us before open case or feedback, we will give you the best solution.
    Item Specifics:
    Brand :auspartshouse
    Manufacturer Part Number :13450916
    Interchange Part Number :K90448
    OE/OEM Part Number :5145SR323
    Manufacturer Warranty :10 Year
    Universal Fitment :No
    Kit or Single Part :Single
    Adjustable :Yes
    Quantity :1 Piece
    Items Included :Mounting Hardware
    Store Speciality :Suspension & Steering
    Placement on Vehicle :Right Front Upper
    Kit Parts Included :Control Arm, Ball Joint
    Surface Finish :Polished, Rust Protected
    Fitment :For Acura, Honda
    Type :Control Arm & Ball Joint Assembly
    Control Arm Construction :Stamped
    OE Spec or Performance/Custom :OE Spec
    Modified Item :No
    Material :Steel
    Features :Easy to Replace
    Cotter Pin Hole :Yes
    Material :Steel
    Mounting Style :Bolt-On
    Finish :Polished

    Payment:
    We use eBay's Safe and Secure Checkout. Just click the Pay Now button at the top of any of the auctions you have won.
     
    To pay for multiple auctions, successfully win all auctions you wish to purchase and then click the Pay Now button on any of the listings you won. You will only have to checkout and pay once for your entire order.
     
    Please review our detailed policies on shipping and fixing any issues before purchasing the item. If you have any questions, please email us through "Ask a question".
     
    Payment Options: Any payment which can be accepted by ebay.
     
    If you want to change the shipping address, please contact us by eBay messages within 12 hours.
     
    Payment must be received within 10 days as auction ended or order might be delayed.
    Shipping:

    2. We only ship to the address in order provided to us. Your order address will be the shipping address.

    4. If you have not received your shipment within 15 days from payment, please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!

    Returns:

    1. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.

    2. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.

    3. Return shipping is to be paid by the Buyer if the problem turned to be buyer's end, or return will be seller's responsibility.

    Feedback:

    We maintain high standards of excellence and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.

    Contact Us:

    Any question or problem, please feel free to contact us via ebay message.


    All rights reserved.