Features:
  • MagCAD Garmin Varia mount for the Pinarello Dogma F.
  • Clamps to your Pinarello Dogma F seat post, remaining secure and fixed in position.
  • Compatible with Garmin Varia radar lights up to the RTL515/516 but NOT the RCT715 camera/radar light.
  • Weighs just 17 grams without hardware.
The Garmin Varia and seat post are pictured for reference only and not included.

What's Included
  • 1x 3D printed mount.
  • 1x M4x30mm cap screw - black stainless steel.
  • 1x M4 dome Nyloc nut - black stainless steel.
Overview
This mount has been a popular request, now available as really clean and secure solution for mounting your Garmin Varia to your Pinarello Dogma F seat post. This design replaces the OEM Varia mount with rubber bands which would always tend to move or rotated whilst out riding.

This mount is compatible with both the offset and inline Dogma F seat posts. It is primarily designed for the Dogma F but will fit some other models within the same Pinarello F and X bike range; F5, F7, Dogma X, X5, X7. It does not fit the Pinarello X3, X1 or older Pinarello models such as the F12, F10 & F8. It may also not fit some painted seat posts depending on the thickness of paint. Feel free to get in contact for more details on compatibility.

Please note the Garmin interface on the Varia devices is the same as the Garmin Edge devices but rotated 90 degrees. Therefore if you mount a Garmin Edge cycle computer to this mount it may not be the correct orientation for your setup.

Please be aware, this MagCAD mount is compatible with Garmin Varia radar lights up to the RTL515/516. It is not compatible with the new Varia RCT715 radar/camera.

​Application
This MagCAD mount will be 3D printed and supplied fully assembled with stainless steel fasteners.
  1. Remove the M4 screw, supplied, and separate the two 3D printed components.
  2. Slot the horseshoe shaped component over the front of the seat post, noting the correct upward position and preventing the M4 Nyloc nut from falling out.
  3. Locate the Varia mount at the back of your seat post and re-install the M4 screw, loosely tightening.
  4. When assembled correctly the Varia interface should be vertical to the ground.
  5. Position up or down your Dogma seat post to suit and tighten the M4 screw to 1Nm with a 3mm Allen key.
  6. Install your Garmin Varia device in the normal quarter turn motion.
All fasteners should be checked periodically to ensure they are still tight.

Compatible With:
  • Garmin Varia devices up to RTL515/516.
  • Not compatible with the Varia RCT715 radar/camera.
  • Pinarello Dogma F, F5, F7, F9, Dogma X, X5, X7, X9.
  • NOT compatible with the X3, X1 or older Pinarello models such as; F12, F10 & F8.
  • May NOT be compatible with some painted seat posts.
Specifications
  • Weight: 17 grams (without hardware), 21 grams (with hardware).
Disclaimer
This product and/or service is not affiliated with, endorsed by or in any way associated with Cicli Pinarello S.p.A, Garmin Ltd, or their products and services. Pinarello, Garmin and their respective logos are trademarks or registered trademarks of Cicli Pinarello S.p.A and Garmin Ltd.

Material
MagCAD Mounts are 3D printed in Nylon PA12. However these are not your typical home 3D printers. Following a process of SLS (Selective Laser Sintering) on industrial size printers, costing anything above £100k, the resulting mounts have fantastic resolution and refinement. The surface finish is slightly rough with a matte effect and the performance of the mounts are comparable to injection moulded parts.

Customisation
As with all MagCAD items it's more than possible to tweak or change the design to suit your particular installation. Feel free to get in contact for more details.

About Me
I’m a MEng Aerospace Engineer and former professional cyclist. All the items, including this mount, are ones which I’ve developed and use myself. A hobby which I take too far but want to share with others.

Delivery
All items in stock and dispatched promptly, usually the same day.

Returns
Should you have any issue or just change your mind we're happy to accept returns within 30 days, providing the item is unused.