Parameters:
Detection range: distance 4-5 metres, angle 100 degrees
Working voltage: AC 220V (self-fitting adapter), DC 6V (4 AA batteries can be installed inside)
Remote control distance: 4-5 metres
1. As the remote control infrared alarm in the human body relative to the lens horizontal movement of infrared detection sensitivity is the highest, and vertical movement sensitivity is poor, so the installation should pay attention to the detector level of the angle and height of the detector, which has a great impact on the protection zone.
2. When installing the infrared warning device should be avoided close to hot and cold sources, such as hot and cold air vents, air conditioning vents, electric heaters, chillers, etc., to avoid direct access to the door.
3. The remote control infrared warning device should be able to see the range of protection, there can be no obstacles.
4. Remote control infrared warning device should be with the wall at an angle of 10 to 30 degrees, this time the detection distance is the farthest, the actual installation of the installation angle adjusted according to the situation.
Installation method:
1. Fix the universal seat at about 2 metres from the ground.
2. Open the battery cover, and load four No.7 batteries according to the marking inside the battery box.
3. Fix the remote control infrared siren on the gimbal, turn the infrared siren to make it meet the installation requirements and detection needs.
Use method:
1. Load the batteries. Press the remote control, the machine issued a ‘tick’ sound, while the green light is on. On behalf of the alarm is ready to enter the working state.
2. Remote control infrared alarm in the green light on the 15-second standby delay, 15 seconds does not detect the alarm signal, you must leave the detection area of the electronic dog in the 15 seconds.
3. After 15 seconds, if a person enters the detection area of the infrared warning device, the red light flashes for 5 seconds. In this 5 seconds delay time, it is convenient for the owner to switch off the alarm with the remote control. 5 seconds later, if no signal is received from the remote control, it will send out a 30-second ear-splitting alarm sound, the alarm volume is 105 DB. 15 seconds after the end of the alarm sound, if there is a person who touches the remote-controlled infrared alarm, it will be alarmed again, and so on and so forth.
Detection range: distance 4-5 metres, angle 100 degrees
Working voltage: AC 220V (self-fitting adapter), DC 6V (4 AA batteries can be installed inside)
Remote control distance: 4-5 metres
Alarm sound level: 105dB (decibel) 30cm at measurement
1. As the remote control infrared alarm in the human body relative to the lens horizontal movement of infrared detection sensitivity is the highest, and vertical movement sensitivity is poor, so the installation should pay attention to the detector level of the angle and height of the detector, which has a great impact on the protection zone.
2. When installing the infrared warning device should be avoided close to hot and cold sources, such as hot and cold air vents, air conditioning vents, electric heaters, chillers, etc., to avoid direct access to the door.
3. The remote control infrared warning device should be able to see the range of protection, there can be no obstacles.
4. Remote control infrared warning device should be with the wall at an angle of 10 to 30 degrees, this time the detection distance is the farthest, the actual installation of the installation angle adjusted according to the situation.
Installation method:
1. Fix the universal seat at about 2 metres from the ground.
2. Open the battery cover, and load four No.7 batteries according to the marking inside the battery box.
3. Fix the remote control infrared siren on the gimbal, turn the infrared siren to make it meet the installation requirements and detection needs.
Use method:
1. Load the batteries. Press the remote control, the machine issued a ‘tick’ sound, while the green light is on. On behalf of the alarm is ready to enter the working state.
2. Remote control infrared alarm in the green light on the 15-second standby delay, 15 seconds does not detect the alarm signal, you must leave the detection area of the electronic dog in the 15 seconds.
3. After 15 seconds, if a person enters the detection area of the infrared warning device, the red light flashes for 5 seconds. In this 5 seconds delay time, it is convenient for the owner to switch off the alarm with the remote control. 5 seconds later, if no signal is received from the remote control, it will send out a 30-second ear-splitting alarm sound, the alarm volume is 105 DB. 15 seconds after the end of the alarm sound, if there is a person who touches the remote-controlled infrared alarm, it will be alarmed again, and so on and so forth.
4. In the remote control infrared alarm, you can use the remote control to close the detection circuit, end the alarm.
Package Included:
1 X Detector（Battery not included）
2 X Remote （Includes button battery）
2 X Screw
