The axial current hydropower generator consists of a water turbine and a coaxial generator.
The water turbine mainly consists of water blades, water supply covers, bearings, water seals, main shafts, etc.
Axial Flow Turbine Generator mainly uses the tension tube of appropriate height to form a vacuum suction tube.
The incoming water from the upstream stream is drawn to form a vortex through the vortex chamber,
and the jet water blades rotate at high speed and drive the generator to work through the main shaft.
The water turbine mainly consists of water blades, water supply covers, bearings, water seals, main shafts, etc.
Axial Flow Turbine Generator mainly uses the tension tube of appropriate height to form a vacuum suction tube.
The incoming water from the upstream stream is drawn to form a vortex through the vortex chamber,
and the jet water blades rotate at high speed and drive the generator to work through the main shaft.
Model: ZL-20-10kw
Power: 10000 W
Head: 5-10M
Flow rate: Q.MAX 0.24m³/s
Phase: single phase
Voltage: 220 V
Tree: 45 A
Rated speed: 1500rpm
Frequency: 50 Hz
Weight: 120 kg
Material: cast iron
Power: 10000 W
Head: 5-10M
Flow rate: Q.MAX 0.24m³/s
Phase: single phase
Voltage: 220 V
Tree: 45 A
Rated speed: 1500rpm
Frequency: 50 Hz
Weight: 120 kg
Material: cast iron
Product structure of Axial Flow Hydrogenerators
(1) Bearing cover
(2) Upper cover
(3) Stock
(4) Rotor
(5) Stator coil
(6) Motor barrel
(7) Lower seat
(8) Bearing
(9) Oil seal
(10) Housing
(11) Water cones
(12) Guide coverage
(13) Runners
(14) Feather cushions
(15) Nut
(16) Split pin
(1) Bearing cover
(2) Upper cover
(3) Stock
(4) Rotor
(5) Stator coil
(6) Motor barrel
(7) Lower seat
(8) Bearing
(9) Oil seal
(10) Housing
(11) Water cones
(12) Guide coverage
(13) Runners
(14) Feather cushions
(15) Nut
(16) Split pin
Working method
Axial flow small water generators are mainly used where the water flow is relatively low, such as small rivers and small streams.
The axial flow small water generator mainly consists of a generator and a impeller coaxial.
Axial flow small water generators are mainly used where the water flow is relatively low, such as small rivers and small streams.
The axial flow small water generator mainly consists of a generator and a impeller coaxial.
Operating principle and mounting method:
First, plan the site, usually next to it, or where there are rocks underneath. Use concrete and stone to build the inlet channel; Use a wooden board to make a switch lock; Use a wire mesh to form a garbage wall to form the water inlet system.
Use a concrete and stone to build a spiral flat channel according to the model, so that the water forms a vortex and drives the impeller to rotate.
Under the spiral plane, a small, large, horn-shaped drawpipe is built, which is mainly used to make the water a suction force inwards and pull the impeller down, thereby generating strong energy to drive the generator.
Therefore, the power of the generator mainly comes from the draw pipe, and the length of the draw pipe is the drop of water flow, called the water head. Small axial current hydrogenerators usually work between 1–6 meters of water head.
First, plan the site, usually next to it, or where there are rocks underneath. Use concrete and stone to build the inlet channel; Use a wooden board to make a switch lock; Use a wire mesh to form a garbage wall to form the water inlet system.
Use a concrete and stone to build a spiral flat channel according to the model, so that the water forms a vortex and drives the impeller to rotate.
Under the spiral plane, a small, large, horn-shaped drawpipe is built, which is mainly used to make the water a suction force inwards and pull the impeller down, thereby generating strong energy to drive the generator.
Therefore, the power of the generator mainly comes from the draw pipe, and the length of the draw pipe is the drop of water flow, called the water head. Small axial current hydrogenerators usually work between 1–6 meters of water head.
