GD100 Product Specifications：
📣Detection: Natural gas, methare propane,butane iso-butane,LPG,LNG,CNG,fuel gases or vapor
📣Sensor: Planar semiconductor

ANCEL GD100 Combustible Gas Leak Detector Pen with Buzzer Alarm Car Pipe Leak Diagnostic Tool Emissions Gas Analyzers Tools
✅Versatile Gas Detection: Capable of detecting a wide range of gases including natural gas, methane, propane, butane, iso-butane, LPG, ING, CNG, and other fuel gases or vapors.

✅Advanced Sensor Technology: Equipped with a planar semiconductor sensor for accurate and reliable detection.

✅Quick Bootup Time: Starts up in just 30 seconds, ensuring prompt readiness for use.

✅Wide Detection Range: Effective detection range from 50 to 1000ppm, suitable for various environments.

✅ Visual and Audible Alarms: Features 3-color LED visual indicators and a variable tone frequency buzzer for clear and immediate alerts.

✅Sensor Failure Indication: Includes a sensor failure indication (VS) to ensure the device is always functioning correctly.

✅Robust Operating Conditions: Operates effectively in temperatures from 0 to 50°C and humidity levels below 90%RH.

✅Reliable Power Source: Powered by two AA 1.5V batteries, ensuring long-lasting performance.

To Operate Unit:
1. Open battery cover and insert two(2) AA batteries (with(+) side pointed towaras tip). The wand shortly sounds two times in case battery correctly installed.

2. Remove the red protective cap before turning on unit. Cap must be off for sensor to work properly.

3. Press and hold the white power button for two seconds to start a 25 second self-inspection, 4 LEDs light will blink in sequence. The detector is ready for use after beep sounds and LED(Yellow, Orange, Red) lights turn off and LED(Green/Red) lights on in green color.

4. Place the sensor tip of the wand along the connection point that you are testing. Be sure cap is off. If checking tor leaks on a gas pipe, be sure to move the sensor slowly along the pipe over joints&fittings. Caution must be taken when utilizing the wand outdoors or in the presence of winds or air flow. Wind direction, strength, leak size and dilution o1 detectable gases may interfere with proper readings or mask a potentially dangerous gas leak.

5. IF GAS IS DETECTED, an audible alarm will accompany a yellow, orange or red light: (LED Yellow, Orange, Red )

GREEN light illuminates-the detector is powered on and Air is safe

YELLOWlight illuminates and buzzer beeps -Small amount of gas detected

ORANGE light illuminates and buzzer beeps - Medium amount of gas detected

RED light illuminates and buzzer beeps-Significant amount of gas detected

WARNING! If red indicators light up, ventilate the area IMMEDIATELY and move to a safe location away from the residence. Then call your local gas utility company for assistance. After leak is repaired, repeat steps 2 through 4.

6.SENSOR FAILURE In case LED(Green/Red) turns to red color with continuous buzzer and LED(Yellow, Orange, Red )are all off during use, the sensor of detector fails is no longer working properly.
Stop using and replace the detector immediately.

7. After use, be sure to turn off the device before storing. To turn off, press the power button once, green light will shut off. Unit will automatically turn off after 5 minutes since powered on. Replace protective cap to help protect sensor and reduce risk of contamination.

8. Be careful not to drop unit or push down on tip. This could damage the sensor.

9. DO NOT dip or submerge detector in liquid. Replace detector if it comes into contact with liquid.

10. DO NOT disassemble detector. Internal contents contain chemicals known to the State of California to cause birth defects or reproductive harm. Replace detector if it has been disassembled.

11. DO NOT use wand in environment with relative humidity above 95%.

12. DO NOT use wand in temperatures less than 15°F or in temperatures greater than 110°F.

COMBUSTIBLE GAS LEAK DETECTOR
Note: At a minimum, replace batteries once a year for optimal performance. (Battery life is limited to approximately 1,000 minutes of usage.) The unit is not working if LED(Green/Red) does not light on in green color.

WARNING! Turn the unit on in a well-ventilated area. Fresh air is needed to generate an accurate "clean" reading. The unit will not operate properly until a "clean" reading has been made.

DANGER! Fuel gases are odorized(rotten egg smell) so that their presence can be detected. If you detect a presence of gas by scent, do not use this device to confirm. Ventilate area immediately and move to a safe location away from the residence. Then call your local gas utility company for assistance.

Wide Applications

Easy To Carry
Smaller size,more convenient to carry auxiliary pen holder design,compact and convenient

Packing List