Feed granulator is widely used in large, medium and small aquaculture, grain feed processing plants, livestock farms, poultry farms, individual farmers, small and medium-sized farms and large, medium and small feed processing plants.
This machine can be used alone, and customers who need it can also match it with a straw cutter for better results.

Note:

1. Before using the machine, it is necessary to adjust the screw of the pressure roller to the appropriate position. The pressure roller and the pressure plate should be closely combined, and the two adjusting screws should be on the same horizontal plane.
2. Please refuel the fuel tank before using the machine. The machine should not idle for more than 2 minutes.
3.Double-check the belt and the screws before operation.
4.After using the machine, clean up the rest to prevent damage to the machine.
5.If the pressure roller cannot rotate normally, please tighten the screws that control the pressure roller first, and then try to power it on. If it still does not work, you can appropriately loosen the screws next to the pressure roller and then tighten them slightly again (without special tightening)
6.This machine only has a body and no plates. If needed, customers can purchase plates for installation according to their own needs.

Parameter:

Pressure plate: without
Output/h: 200-250kg
Power: 7.5kW
Voltage: 220V Three-phase electricity
Product body material: Cast iron
Standard pressure roller: Two-head press roller
Product size: 39.56*14.17*36.8in(100.5*36*93.5cm)
　

Product analysis:

Feature:

This machine is equipped with an enlarged and widened discharge port to prevent feed from splashing and facilitate the feed collection conducted by customers.

The machine is equipped with mobile wheels for easy handling and movement.

Enlarge the feed inlet
The machine adopts the design of enlarged feed port, which makes it more convenient for you to feed raw materials and effectively improves work efficiency.

Here is the filling port, open here to add engine oil
It is recommended to add high-quality machine oil or hyperbola heavy-duty gear oil.(The color of the oil filling plug is random)

The length of feed particles can be adjusted here.

After using the machine for a period of time, the customer needs to add lubricating oil here to lubricate the grinding chamber (approximately 4-6 months of use) (the lubricating oil gun and lubricating oil need to be purchased by the customer themselves, we do not provide them).

The voltage display meter can clearly show the voltage, making it convenient for customers to distinguish the correct voltage.

Materials can leak out here to prevent materials from accumulating in the grinding chamber.

The adjustable nut is used to adjust the distance between the pressure roller and the grinding disc. When making pellets, the nuts on the two sides must be balanced to avoid damage to the pressure roller and grinding disc.
If the pressure roller cannot rotate normally, please tighten the screws that control the pressure roller first, and then try to power it on. If it still does not work, you can appropriately loosen the screws next to the pressure roller and then tighten them slightly again (without special tightening)

Precautions:

1.When using, it should be noted that there should be no foreign matter such as stones and iron blocks in the raw materials. After the pellet machine has been working continuously for more than ten shifts, the pressure roller oil hole, the universal joint oil hole, and the linkage shaft oil hole need to be filled with high-temperature lubricating grease to make the pressure roller have good working performance and extended bearing life.
2.During granulation, it is strictly forbidden for the pressure roller to make contact with the template to run idly, and the continuous feeding can not be interrupted.At the same time, the pressure roller shaft nut is locked to avoid loosening and damaging the spindle keyway.
3.When granulating, there is no granulation and no discharge, the template should be removed, and after opening one by one, some fiber feed can be added appropriately to restart the granulation.
4.Always check the tightness of the screws in each part of the machine. If there is oil leakage in the gearbox, replace the oil seals in time, and check whether the bearings in the machine head are short of oil.
5.When the pellet machine is working, do not reach into the feeding port with your hands. If necessary, use wooden sticks to help feed the pellets.
6.Before turning on the machine, it is necessary to add less materials. When shutting it down, leave a small amount of feed in the machine to prevent the press roller of the machine from contacting the template to idle.
7.If the machine is stuck in operation, stop it immediately, press the pressure roller until the bolt is flat,and then restart the machine.
8.Each time the work is completed, the adjusting pressure roller bolts must be loosened.
9.Iron or stones cannot be put into the machine.
10.Check the elasticity of the belt, and the bearing frequently. Add oil in time when it needed.

Note:

1.We suggest that high-power machines should be directly connected to the main power supply, as the voltage reaching the machine is stable. If the voltage is unstable and the current exceeds the rated current of the motor, it is easy to burn out the starting capacitor.
2.It is recommended to directly connect the machine to the power supply as much as possible. If the machine is not connected to the power supply, different situations may occur, and the wires are not durable. The wires will gradually burn out over time.
3.Our machine is not equipped with a plug. If you do not know how to operate the wiring , you can contact our customer service and we will provide you with the wiring video.

Item include:

Feed Pellet Mill Machine Body without Plate 220V (238009)