Crankshaft BGM Touring rotary valve 57mm stroke for Vespa PX200 – Bild 1
Crankshaft BGM Touring rotary valve 57mm stroke for Vespa PX200 – Bild 2
Crankshaft BGM Touring rotary valve 57mm stroke for Vespa PX200 – Bild 3
Crankshaft BGM Touring rotary valve 57mm stroke for Vespa PX200 – Bild 4
Crankshaft BGM Touring rotary valve 57mm stroke for Vespa PX200 – Bild 5
Crankshaft BGM Touring rotary valve 57mm stroke for Vespa PX200 – Bild 6
BGM

Crankshaft BGM Touring rotary valve 57mm stroke for Vespa PX200

Art. ID.: 1130509

Art. No.: BGM-031800G

Manufacturer: BGM

General

  • Type
    Crankshaft
Description
MATERIAL
The bgm PRO Touring crankshafts are forged. The material is heavily compacted by the forging process. Structurally, it is therefore many times more resilient than conventionally manufactured cheeks made of 'rod material'. We use this high resistance to increase the compression ratio of the lift pin and to be able to offer a crankshaft with maximum torsion resistance.

STORAGE
The lower connecting rod bearing is lubricated via two large lubrication slots and a total of four additional pockets on the side. The SSC racing bearing and the side thrusters ensure solid storage. The upper connecting rod bearing is lubricated via two lubrication holes. The INA piston pin bearing is included with the crankshaft.

CONROD
The connecting rod
is made extra solidly and, like the crankwalls, is forged in the drop. The result is an extremely durable connecting rod that easily withstands the strong torques of today's engine concepts over the long term.

HUB
The shaft is available with 60mm (long stroke) and 57mm (standard) stroke. With the long stroke variant, more displacement is achieved, and at the same time, the control angles of the cylinder (overflow and outlet channels) can be changed to increase performance.


The bgm PRO Touring wave has a significantly better intake time layout compared to many other racing waves. With tuning cylinders, the standard shaft, with its very short intake time, does not keep up. On the other hand, the bgm PRO shaft closes approximately 65° after the upper dead center on a PX motor housing (depending on the motor housing, this varies from factory to factory). The motor can be easily adjusted with these control angles. Tip: If the intake is machined in such a way that the crankshaft releases the intake slot earlier, additional power can be gained. The good value here was around 110-115° from above ground.

APPROVAL
The crankshaft design of the PX engines is based on that of the first 125cm³ engines from 1960 with an output of approx. 5 hp. Unfortunately, Piaggio never really changed this construct during subsequent engine capacity expansions. For example, the load capacity of the crankshaft has already been mathematically exhausted with the standard 200cc models with 12hp. The crankwalls are very narrow and have very little coverage (cheek material that, seen in diameter, is available above the lower lifting pin). As a result, neither a particularly high press capacity nor a large lifting pin can be used, as would be necessary (for the performance of today's engines).
For this reason, the BGM PRO Touring crankshafts have a very high material quality and bearings. In addition to the very rigid material, which allows us to guarantee very strong compression of the lifting pin, it is also bonded with a special industrial adhesive for maximum torsion resistance. Based on the positive experience gained in many thousands of kilometers of testing our own engines used daily, we fully approve BGM PRO Touring crankshafts for engine outputs of up to 25 hp. For motors in this performance region, we recommend using a lighter pole wheel with a maximum weight of 2300 gr.

Conclusion
The bottom line is that the bgm PRO crankshaft offers the highest quality for every component in all respects. Precision in production, materials used and, above all, precise balancing leave nothing to be desired. This guarantees extremely smooth and vibration-free motor operation.

Tip
It is best to order the 24x35x7 shaft sealing ring directly from Gilera Runner. The seat of the bgm wave is wider than usual and can therefore be driven with a double-lipped Viton Wedi.

Suitable for

Crankshaft BGM Touring rotary valve 57mm stroke for Vespa PX200 suitable for

MotoVespa DN Motor 9DN
Vespa Cosa 1 200 (Bj. 1988) (2-Takt) (VSR1T)
Vespa Cosa 2 200 (Bj. 1991) (2-Takt) (VSR1T)
Vespa Cosa 200
Vespa P 200 X/E (Bj. 1977) (2-Takt) (VSX1T)
Vespa PX 200 (2-Takt) (VSX1T)
Vespa PX 200 E / Lusso (Bj. 1983) (2-Takt) (VSX1T)
Vespa PX 200 E GS (Grand Sport) (Bj. 1987) (2-Takt) (VSX1T)
Vespa PX MY 200 (Bj. 1998) (2-Takt) (VSX1T)
Vespa Rally 200 (Bj. 1972) (2-Takt) (VSE1T)