Happymodel 2.4GHz ELRS Receiver Mini Micro EPW6 PWM Output (ExpressLRS)

Versatile Compatibility: The Happymodel 2.4GHz ELRS Receiver Mini Micro EPW6 PWM Output is compatible with a wide range of flight controllers and devices that support PWM signal input. This compatibility ensures seamless integration into your existing setup, allowing for easy and convenient installation. Reliable and Extended Range: Experience a reliable and extended control range with the Happymodel ELRS Receiver. It provides a strong and stable signal connection, minimizing the risk of signal loss and ensuring consistent control over your drone or RC model even at longer distances. Compact and Lightweight Design: The Mini Micro EPW6 PWM Output Receiver is designed with a compact and lightweight form factor, making it suitable for various drone and RC model configurations. Its small size does not compromise its performance, providing a convenient solution without adding unnecessary weight to your aircraft. ExpressLRS Compatibility: This receiver module is fully compatible with ExpressLRS, an open-source long-range radio system. By utilizing the power of ExpressLRS, you gain access to features such as low latency, fast data transmission, and extensive configurability, enhancing the overall control and responsiveness of your flying experience. Specifications: Item: Happymodel EPW6 TCXO 2.4GHz PWM receiver ESP8285, SX1280/1281 Antenna connector: IPEX MHF 1/U.FL 6x PWM outputs RF Frequency: 2.4GHz (2400~2480MHz) Telemetry power: 12dbm Receiver protocol: PWM or CRSF Input voltage: +5v~8.4v PCB size: 19mm x 17.5mm Weight: 1.49g / antenna Firmware Target option 1: Generic ESP8285 6xPWM 2.4Ghz RX PWM receiver via 1~6 PWM outputs Target option 2: HappyModel_EP_2400_RX CRSF Serial receiver via TX and RX Firmware update via WIFI Bind Procedure: Supply power to the EPW6 RX, wait until the Green LED on the RX is off, immediately turn off the power, and then repeat again the above steps. When the RX is powered on for the third time, the Green LED light will start to double-flash, which means that the RX enters the binding mode Get into the menu of ELRS.LUA V2.0 version from your radio transmitter and then press BIND, the Green LED on the RX module will turn solid if bound successfully. Receiver LED Codes Features: LED solid means bind successful or Connection established; LED double-flash means in bind mode; LED flash slowly means no signal connection from the TX module; LED flash fast means in WIFI hotspot mode, you can connect the WIFI of the RX and upgrade the firmware of the RX via visit 10.0.0.1 from the web browser (password: expresslrs) Package Contents: 2 x 2.4GHz antenna 1x 6pin 2.54mm

Happymodel 2.4GHz ELRS Receiver Mini Micro EPW6 PWM Output (ExpressLRS)

Versatile Compatibility: The Happymodel 2.4GHz ELRS Receiver Mini Micro EPW6 PWM Output is compatible with a wide range of flight controllers and devices that support PWM signal input. This compatibility ensures seamless integration into your existing setup, allowing for easy and convenient installation.

Reliable and Extended Range: Experience a reliable and extended control range with the Happymodel ELRS Receiver. It provides a strong and stable signal connection, minimizing the risk of signal loss and ensuring consistent control over your drone or RC model even at longer distances.

Compact and Lightweight Design: The Mini Micro EPW6 PWM Output Receiver is designed with a compact and lightweight form factor, making it suitable for various drone and RC model configurations. Its small size does not compromise its performance, providing a convenient solution without adding unnecessary weight to your aircraft.

ExpressLRS Compatibility: This receiver module is fully compatible with ExpressLRS, an open-source long-range radio system. By utilizing the power of ExpressLRS, you gain access to features such as low latency, fast data transmission, and extensive configurability, enhancing the overall control and responsiveness of your flying experience.

Specifications:

  • Item: Happymodel EPW6 TCXO 2.4GHz PWM receiver
  • ESP8285, SX1280/1281
  • Antenna connector: IPEX MHF 1/U.FL
  • 6x PWM outputs
  • RF Frequency: 2.4GHz (2400~2480MHz)
  • Telemetry power: 12dbm
  • Receiver protocol: PWM or CRSF
  • Input voltage: +5v~8.4v
  • PCB size: 19mm x 17.5mm
  • Weight: 1.49g / antenna
  • Firmware
  • Target option 1: Generic ESP8285 6xPWM 2.4Ghz RX
  • PWM receiver via 1~6 PWM outputs
  • Target option 2: HappyModel_EP_2400_RX
  • CRSF Serial receiver via TX and RX
  • Firmware update via WIFI


 Bind Procedure:

  • Supply power to the EPW6 RX, wait until the Green LED on the RX is off, immediately turn off the power, and then repeat again the above steps. When the RX is powered on for the third time, the Green LED light will start to double-flash, which means that the RX enters the binding mode
  • Get into the menu of ELRS.LUA V2.0 version from your radio transmitter and then press BIND, the Green LED on the RX module will turn solid if bound successfully.


 Receiver LED Codes Features:

  • LED solid means bind successful or Connection established; LED double-flash means in bind mode; LED flash slowly means no signal connection from the TX module; LED flash fast means in WIFI hotspot mode, you can connect the WIFI of the RX and upgrade the firmware of the RX via visit 10.0.0.1 from the web browser (password: expresslrs)


 Package Contents:

  • 2 x 2.4GHz antenna
  • 1x 6pin 2.54mm

×

Buy now and save!

Shipping info

Click the Shipping & Payments tab above the listing description for more info

Click the Shipping & Payments tab above the listing description for more info!

Additional delivery notes

PICK UP OPTION

Sorry, our items are NOT available for pick-up.

PAYMENT


Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart.

We accept payment via U.S. PayPal accounts and all Major Credit Cards, Debit Cards & Google Pay.

We are legally required to collect sales tax in those states and localities where we maintain a physical presence (nexus).

The applicable amount of sales tax charged to an order will be calculated based on the shipment destination's state and local sales tax laws.

Thank you for shopping with us on eBay!

Additional Information

No additional information at this time

Ask seller a question

To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist.

Ask seller a question

© SpeedyFPV

Click the Shipping & Payments tab above the listing description for more info

Accepted Payment Methods

Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart.

We accept payment via U.S. PayPal accounts and all Major Credit Cards, Debit Cards & Google Pay.

We are legally required to collect sales tax in those states and localities where we maintain a physical presence (nexus).

The applicable amount of sales tax charged to an order will be calculated based on the shipment destination's state and local sales tax laws.

Thank you for shopping with us on eBay!

Returns are accepted

Items must be returned within 30 days of the auction ending

Buyer will pay for return shipping.