Precautions for use:
1. After the package is opened, please check if the system is damaged during
transportation. The contents listed on the packing list are consistent with
the contents of the box.
2. This manual is applicable to the CNC system of SF-2100C-QG cutting
machine produced by Beijing Star Peak Control Technology Co., Ltd.
3. Please check if the grid voltage is correct. An AC220V isolation
transformer is used between the grid and the system to ensure reliable
system operation and personnel safety.
4. The numerical control system requires the working environment temperature
to be 0 °C ~ +40 °C, and the relative humidity is 0-85%.
Special protection is required if working in environments with high
temperatures, high humidity and corrosive gases.
5. The wiring of each part of the CNC system should be correct and the
ground wire should be in good contact.
6. The CNC system does not allow all the cable plugs on the rear of the
chassis to be plugged and unplugged. As a result, the company refuses the
warranty.
7. The line of the rear output port of the CNC system is not allowed to be
short-circuited with other power lines; otherwise, the CNC will be burned.
8. In a high dust environment, the whole machine needs to be dustproof, and
it is necessary to clean the dust regularly to ensure the cleaning of the
CNC system.
9. The CNC system should be managed by a dedicated person and the operator
should be trained.
10. It is not allowed to connect the AC/DC power supply used inside the CNC
system to other appliances.
11. In case of problems, please contact us. Do not disassemble or modify the
system yourself without being familiar with it.
12. Maintain the system and machine tool, perform routine maintenance and
inspection every shift; perform secondary maintenance once a month; perform
primary maintenance every six months.
13. The parameters set by the CNC system should be set strictly in
accordance with the instructions in this manual or the supplementary
instructions at the time of ordering; if the set parameters are outside the
specified range, the CNC system will work abnormally or even be damaged.
14. The LCD screen of the system is fragile, and the LCD should be protected
during use.
15. The technical specifications of this system are subject to change
without prior notice.
16th. Note: The
USB port output power of the system is very small, and it can only be used
by the U disk. It cannot be connected to other USB devices to prevent
damage.
System functions
SF-2100C-QG cutting machine CNC system is suitable for all kinds of flame /
plasma, high pressure water jet, laser cutting machine, widely used in metal
processing, advertising, stone and other industries.
The system is highly reliable and has the ability to resist plasma
interference, lightning strikes and surges.
Practical flame/plasma cutting process, automatic corner rotation control
and height control control during plasma processing; remote operation with
wireless remote control.
It has the function of kerf compensation, and whether the compensation in
the program is reasonable, and the corresponding report is made for the user
to choose;
Breakpoint recovery, automatic power-off recovery function, automatic memory
breakpoints;
Arbitrary selection and selection of perforation point processing functions;
It has an epitaxial perforation function for thick plates and a bridging
function for thin plates;
Back-off, selection, breakpoint recovery, optional perforation position and
other functions, greatly facilitate the user's control;
Transfer cutting at any time;
It adopts a special small line segment processing function, which makes it
easy to walk and can be widely used in metal cutting and advertising,
wrought iron, etc.
A library of 24 graphics (expandable and customizable) containing common
basic machining parts;
Fully compatible with StarCAM nesting software, compatible with IBE
(Germany), FASTCAM and other mainstream nesting software;
Chinese and English operation interface conversion, dynamic graphic display,
1 to 8 times of graphic magnification, automatic tracking of moving points,
U disk reading program and timely software upgrade.
1.2 Technical indicators
Processor: using
industrial grade ARM processing chip;
Display: 7-inch
color LCD display;
InputOutput: The
system provides 16 optically isolated inputs and 16 optically isolated
outputs.
Number of linkage axes: 2
axes, (can be driven by X-axis bilaterally or Y-axis bilaterally)
Maximum speed: not
less than 24 m / min;
Pulse equivalent: flexible
adjustment;
Storage space: 4G
large user program storage capacity, processing procedures are not limited;
Chassis size: 298
× 202 × 65 (mm);
Working temperature: 0
° C ~ +40 ° C; storage temperature : -40 ° C ~ +60 ° C ;
Function word definition:
N command segment number
G preparation function
M auxiliary function
T tool function (in this system is the flame width)
L cycle number, delay time
X X axis (diameter) absolute coordinates
Y Y axis absolute coordinates
I When the arc is machined, the center coordinate value is reduced by the X
axis starting point value.
When the arc is machined, the center coordinate value is reduced by the Y
axis starting point value.
R arc radius specification
H arc string height specification
A auxiliary variable
F machining speed specification for G01, G02, G03
parameter description.
Speed parameter
Starting speed, adjustment time and maximum speed limit of each axis;
System Parameters
Electronic gear ratio of each axis, machine origin, reference point,
backlash, line offset, soft positive/negative limit;
Flame cutting parameters
Ignition delay, preheating delay, cutting gun up/down delay, perforating
torch up/down, piercing delay, etc.
Plasma parameter
Cutting gun positioning delay, M command for arcing, M command for arc
breaking, arc pressure detection selection, positioning detection selection,
piercing delay;
control parameter
Flame/plasma selection, processing speed limit, edge perforation selection,
metric/imperial selection, etc.
Storage Function
The modified parameters are stored in the parameter area.
Press the S key continuously to select the external manual control button to
select whether it is valid or invalid.
Software upgrade operation instructions (software free upgrade)
First, the operation steps
1. Format the USB flash drive in FAT or FAT32 format. It is recommended to
use the FAT format.
2. Copy the upgrade file into the USB flash drive. The name of the upgrade
file must be STARTCNC.EXE.
3. Press and hold the arrow button on the left side of the USB port to power
on the system, power up the system, and plug the USB disk into the USB port
of the system.
4. The system automatically enters the upgrade interface, press the F1
button on the panel (ie, the corresponding button for the upgrade);
5. If the upgrade is normal, after the upgrade is complete, the system will
display “Upgrade Successful!”.
6. Turn off the power, pull out the USB flash drive, and the upgrade process
is complete.
Second, the exception process of the upgrade process
Check that the name of the upgrade file must be STARTCNC.EXE.
If this factor has been eliminated, you can re-operate according to the
operation steps. If multiple attempts still fail, you can call customer
service.