The Axis Adhesive Mic Holder is simple gear that keeps your UHF mic parked in the same spot every time, instead of sliding around the seat or floor on rough tracks. Stick it on a clean section of dash or console and you have a fixed dock for day-to-day radio chat, handy for highway convoys or short runs out to the job site.
The holder is made from black ABS plastic with a compact face area of roughly 40 mm by 40 mm, so it fits neatly beside gauges or switch panels without crowding the cab. An adhesive backing handles normal cabin heat and vibration, so the cradle stays put once you press it on. The open slot suits standard UHF mic bodies, so you can drop the mic in and get out there without juggling cables or clips.
- Axis adhesive-back microphone holder
- Suits general UHF radio microphones
- Compact cradle helps keep dash tidy
- Black ABS plastic construction
- Adhesive mounting avoids drilling holes
- Open-front slot for quick mic access
- Low profile design to reduce snagging
- Suitable for flat interior trim surfaces
- Model code MH3B for simple reference
- Handy add-on for touring and work vehicles
Q: Will this holder work with any UHF microphone?
It suits most standard UHF microphones that use a clip-in style cradle. The opening is shaped for common mic bodies, so most handheld UHF mics will sit securely. Very large or unusually shaped mics may not fit as well. Check your existing mic clip size against the holder before sticking it down.
Q: Can I remove or reposition the holder once it is stuck on?
You can usually remove it, but the adhesive pad may not be reusable. The adhesive is intended for a firm, long-term bond, so it can leave residue on some surfaces when removed. If you plan to move it later, mount it on a trim piece that you are comfortable cleaning. Use adhesive remover suitable for your vehicle trim if needed.
Q: Where is the best place to mount this in the vehicle?
The best spot is a flat, clean surface within easy reach that does not block airbags, vents or controls. Many drivers choose the side of the centre console or lower dash panel. Always test mic reach with the cable before final placement. Wipe the area with suitable cleaner and let it dry fully before sticking the holder on.
Q: Does the holder require screws or extra hardware?
No, the holder uses its built-in adhesive backing only. This means you do not need to drill trim panels or run extra fasteners into the dash. Just peel the liner, press it firmly into place and hold for several seconds. Allow time for the adhesive to bond properly before hanging the microphone.
The holder suits UHF radio microphones that clip into a standard open front cradle. The adhesive backing mounts to a flat clean surface in the vehicle cabin. The holder does not specify any particular vehicle make or model. No additional brackets or fasteners are listed as required beyond the supplied adhesive backing.
About Outback Equipment
Started by a few mates with a shared passion for 4WDs and all things outdoors – Outback Equipment was built on the ideal of bringing old world service back to online shopping.
No flashy sales tactics, no gimmicky products – just good old-fashioned customer service and honest advice.
We only carry a range of products that we would personally use ourselves, products tried and tested for Australian conditions.
We cater to the broadest range of individuals, from the rookie 4WD and camper just getting started, to the saltiest of you outback veterans.
We are 100% Australian owned and operated with our warehouse located in Brisbane.
Due to recent eBay policy changes we can no longer take calls directly to us. You can however still contact us via eBay messages.
Outback Equipment is committed to customer satisfaction. If you are unhappy with any product you receive, simply contact us so we can work with you to resolve the issue as quickly as possible.
Broken or faulty products
If a product is found to be defective, please contact our customer service team as soon as you are made aware of the problem. A repair, replacement, or refund will be organised after consulting with the manufacturer or supplier.
Note: The standard warranty across most products is 12 months unless otherwise specified by the manufacturer.
Change-of-mind or incorrect choice
Customers have up to 30 days to request an exchange or store credit. Items must be returned in original, undamaged condition.
Note: Online store credits are only applicable for purchases made through our webstore.
Return shipping
If a product is deemed faulty and returned within 60 days of purchase, Outback Equipment will provide a Postage Paid label. Claims outside this period are considered warranty claims and postage is the customer's responsibility.
Return address:
Outback Equipment, 1 Murdoch Cct, Acacia Ridge QLD 4110
Please contact Outback Equipment before returning any items.
Fitment or Assembly of Goods
For goods requiring fitment or assembly, our return policy cannot extend beyond the value of the item. Parts must only be fitted by a qualified person. Goods should be inspected for damage prior to installation — no warranty claims will be accepted once fitted.
If you cannot find the answer below, please contact us via eBay between 8.00am–4.30pm Monday to Friday.
My order arrived damaged – what should I do?
Contact us by messaging our eBay store to arrange a return.
I have received the wrong product – what should I do?
Send us a message as soon as possible detailing the error and our team will resolve the issue.
My order never arrived – what should I do?
Contact us through eBay as soon as possible.
I wish to return an item – how do I do this?
Please refer to our Returns tab above for full details.
