2. This machine with 8 plates.We selling 2mm,3mm,4mm,5mm,6mm,8mm,10mm and 12mm plate.Pls contact us if you need plates.

3.Pls don't put your hands into it when it's working.

4. The machine with no plug,pls connect the breaker for working.

5. Before using the machine, it is necessary to adjust the screw of the pressure roller to the appropriate position. The pressure roller and the pressure plate should be closely combined, and the two adjusting screws should be on the same horizontal plane.

6. Please refuel the fuel tank before using the machine. The machine should not idle for more than 2 minutes.

7. Double-check the belt and the screws before operation.

8. After using the machine, cleaning up the rest to prevent damage to the machine.

9. If the pressure roller cannot rotate normally, please tighten the screws that control the pressure roller first, and then try to power it on. If it still does not work, you can appropriately loosen the screws next to the pressure roller and then tighten them slightly again (without special tightening).

10. We suggest that high-power machines should be directly connected to the main power supply, as the voltage reaching the machine is stable. If the voltage is unstable and the current exceeds the rated current of the motor, it is easy to burn out the starting capacitor.

1. Before turning on the machine, add the lubricating oil (edible oil or engine oil) into the gearbox.

2.After connecting the machine to the 220V power supply, start checking whether the machine operates normally.

3.Machine grinding requires 40% fine sand, 50% sawdust (replaced by bran or corn flour), and 10% machine oil (or replaced by edible oil).The purposes of grinding are to make the new grinding disc and the new pressure rollers of the new machine run more smoothly, and also to make the holes of the new grinding disc smooth for later feeding.

4.Install the pellet machine steadily, check whether the screws in each part are loose, loosen the adjustment screw on the roller shaft base, so that the feed machine is in a no-load state, and it can be put into use after it starts and runs normally. 

5. Before using the new machine for the first time, turn the adjusting screw to make the two rollers have the same speed. If one or two of the pressure rollers do not rotate, adjust and control the screws on the pressure rollers and turn them for a half circle at the same time. If the pressure rollers still do not rotate after turning the screws for a half turn, turn the screws for a half circle at the same time again until the pressure rollers rotate.

4. Conduct normal feeding. During grinding operation, the feeding speed should be slow and should not be too fast. The humidity of the material should be well controlled, and the humidity and dryness should be uniform. (If you cannot master the humidity and dryness, you can experiment for several times and finally master the appropriate degree.)

5. After feeding of the grinding materials is finished, observe the discharge situation of the discharge outlet, and check whether the particles at the discharge outlet have been discharged completely and whether there are remaining materials in the material bin of the feeding inlet. If there is no material left or a small part of the materials have not been discharged from the material bin, this is a normal phenomenon, and the processing operation of normal materials in the later period cannot be affected.

6.Turning off the power. If the machine is not used any more, it can be cleaned easily. If the machine is used again, normal processing materials can be directly fed into the feeding bin (there are some residual grinding materials in the holes of the grinding disc, the grinding materials in the hole disc will come out of the discharge outlet as the normal processing materials enter, and these particles can be chosen not to be used). After feeding and processing of the normal materials are finished, some oil materials can be selected and fed to keep the hole disc in an oil lubricating state, so that the discharge will be smooth when the next batch of normal materials enters the material bin again.

Shipping & Handling Details

Default  Shipping Cost or Free Shipping   Information: 

▲ Default shipping cost or free shipping service is only for the customers  from Canada or the lower 48 United States by Canada Post, USPS or the UPS Ground.Customers from other    areas or needs other shipping  ways, please contact us.
▲ Buyers from Guam,Puerto Rico, Virgin Islands, American Samoa,Alaska,Hawaii,PO Boxes, APO/FPO addresses or other  countries/areas, there WILL be extra shipping costs,   please  contact us for more detailed information.
▲ Please make sure your address is valid for both UPS and USPS services. Any costs incurred because of incorrect or undeliverable address should be undertaken by buyer.

Handling Time: Shipping is usually made in 1-3 business days after payments cleared.  Orders  are processed from Monday-Friday; Not on   the  weekends & public holidays.

Sales tax/Customs duties: Any sales taxes or Customs duties are not included. If came   out,  they  must be undertaken by the buyer.

Damage In Shipping: Email or call us First! We will work with you to get the case resolved in  the fastest method.

Return /  Refund

If you are not 100% happy with your purchase,  please  contact Us. Please don't directly opened  a request  or case without  informing us, or else, we will do some  discounts on the warranty and  other  sales-services  later  on. Hope for your understanding.

Returns & Exchanges

▲ All returns must be made within 14 days of delivery date.  Items must be  in new, unused condition, with all  original materials included with  the shipment. A partial  refund may   be applied for opened or damaged  items,  depending on the condition.
▲ Items returned under the buyer's remorse: The return shipping  fee must be  covered by the buyer;The original shipping  cost will also be  deducted from the refund. 15%  restocking fee  of the items purchase  price will be  charged. 
▲ Returns that are the result of our seller's error: Buyer will receive a full  refund of the item as well as shipping    charges
▲ All    returns  require a RA (Return Authorization) number that   will be   given by our seller. Please contact with us at   first for  more  details.

Defective & Damaged Products 

▲ If product was received damaged or not as described, please send us  some pictures or videos, so we could well understand your problem,  then solve them for you ASAP. Besides, it's much helpful for us to  claim with UPS,remind  our related department to pay much more  attention   to  packaging later on. Hope for your understanding.
▲ Replacement or refund of defective or damaged products can only be returned in  exchange for the exact same product,or else,the purchase price  will be refunded back to your original payment method. 
▲ If an item is received damaged,customer service must be contacted within 7 days of receiving your item. All returns  require a RA  (Return Authorization) number as above.

Warranty  &   Feedback