smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-71-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION === Model Family: Western Digital Red (CMR) Device Model: WDC WD60EFRX-68L0BN1 Serial Number: WD-WX51D175FV09 LU WWN Device Id: 5 0014ee 20e8705cc Firmware Version: 82.00A82 User Capacity: 6 001 175 126 016 bytes [6,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5700 rpm Device is: In smartctl database 7.3/5625 ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Aug 17 13:35:59 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. Warning: This result is based on an Attribute check. See vendor-specific Attribute list for failed Attributes.
General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5744) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 711) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported.
SMART Error Log Version: 1 ATA Error Count: 37925 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 37925 occurred at disk power-on lifetime: 11774 hours (490 days + 14 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 20 1c 07 e0 Error: UNC 8 sectors at LBA = 0x00071c20 = 465952
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 20 1c 07 e0 08 16d+22:57:44.996 READ DMA ec 00 00 00 00 00 a0 08 16d+22:57:44.991 IDENTIFY DEVICE ef 03 42 00 00 00 a0 08 16d+22:57:44.991 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 08 16d+22:57:44.991 IDENTIFY DEVICE c8 00 08 20 1c 07 e0 08 16d+22:57:37.974 READ DMA
Error 37924 occurred at disk power-on lifetime: 11774 hours (490 days + 14 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 20 1c 07 e0 Error: UNC 8 sectors at LBA = 0x00071c20 = 465952
Error 37923 occurred at disk power-on lifetime: 11774 hours (490 days + 14 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 00 1c 07 e0 Error: UNC 8 sectors at LBA = 0x00071c00 = 465920
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 00 1c 07 e0 08 16d+22:57:23.411 READ DMA ec 00 00 00 00 00 a0 08 16d+22:57:23.402 IDENTIFY DEVICE ef 03 42 00 00 00 a0 08 16d+22:57:23.402 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 08 16d+22:57:17.649 IDENTIFY DEVICE ec 00 00 00 00 00 a0 08 16d+22:57:07.672 IDENTIFY DEVICE
Error 37922 occurred at disk power-on lifetime: 11774 hours (490 days + 14 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 00 1c 07 e0 Error: UNC 8 sectors at LBA = 0x00071c00 = 465920
Error 37921 occurred at disk power-on lifetime: 11774 hours (490 days + 14 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 e0 1b 07 e0 Error: UNC 8 sectors at LBA = 0x00071be0 = 465888
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 e0 1b 07 e0 08 16d+22:56:49.236 READ DMA ec 00 00 00 00 00 a0 08 16d+22:56:49.229 IDENTIFY DEVICE ef 03 42 00 00 00 a0 08 16d+22:56:49.229 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 08 16d+22:56:48.790 IDENTIFY DEVICE ec 00 00 00 00 00 a0 08 16d+22:56:38.868 IDENTIFY DEVICE
SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-71-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION === Model Family: Western Digital Green Device Model: WDC WD30EZRX-00DC0B0 Serial Number: WD-WCC1T0895307 LU WWN Device Id: 5 0014ee 25dbbc4ab Firmware Version: 80.00A80 User Capacity: 3 000 592 982 016 bytes [3,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database 7.3/5625 ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Aug 17 12:17:05 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check.
General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (39900) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 400) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70b5) SCT Status supported. SCT Feature Control supported. SCT Data Table supported.
SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Aborted by host 10% 95 - # 2 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-71-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION === Model Family: Western Digital RE4-GP Device Model: WDC WD2002FYPS-02W3B1 Serial Number: WD-WCAVY7437699 LU WWN Device Id: 5 0014ee 2068caff9 Firmware Version: 04.01G02 User Capacity: 2 000 398 934 016 bytes [2,00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database 7.3/5625 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Aug 17 00:45:31 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check.
General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (43680) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 420) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported.
SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5010 -
SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-71-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION === Model Family: Seagate Surveillance Device Model: ST1000VX000-9YW162 Serial Number: S1D0W3GA LU WWN Device Id: 5 000c50 04aa32fbe Firmware Version: CV12 User Capacity: 1 000 203 804 160 bytes [1,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5625 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Aug 17 09:16:02 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check.
General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 575) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 108) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x10b9) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported.
SMART Error Log Version: 1 ATA Error Count: 1586 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1586 occurred at disk power-on lifetime: 64716 hours (2696 days + 12 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 80 3f a0 00 Error: UNC at LBA = 0x00a03f80 = 10502016
Error 1585 occurred at disk power-on lifetime: 64716 hours (2696 days + 12 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 08 08 00 00 Error: UNC at LBA = 0x00000808 = 2056
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 08 08 00 40 00 00:00:36.846 READ DMA EXT ec 00 01 00 00 00 00 00 00:00:36.845 IDENTIFY DEVICE b0 d8 00 00 4f c2 00 00 00:00:36.845 SMART ENABLE OPERATIONS ef 02 00 00 00 00 00 00 00:00:36.844 SET FEATURES [Enable write cache] e1 00 00 00 00 00 00 00 00:00:36.844 IDLE IMMEDIATE
Error 1584 occurred at disk power-on lifetime: 64716 hours (2696 days + 12 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 00 48 a0 00 Error: UNC at LBA = 0x00a04800 = 10504192
Error 1583 occurred at disk power-on lifetime: 64716 hours (2696 days + 12 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 80 3f a0 00 Error: UNC at LBA = 0x00a03f80 = 10502016
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 80 3f a0 40 00 00:00:31.604 READ DMA EXT ec 00 01 00 00 00 00 00 00:00:31.602 IDENTIFY DEVICE b0 d8 00 00 4f c2 00 00 00:00:31.602 SMART ENABLE OPERATIONS ef 02 00 00 00 00 00 00 00:00:31.602 SET FEATURES [Enable write cache] e1 00 00 00 00 00 00 00 00:00:31.602 IDLE IMMEDIATE
Error 1582 occurred at disk power-on lifetime: 64716 hours (2696 days + 12 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 08 08 00 00 Error: UNC at LBA = 0x00000808 = 2056
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 ff ff ff 4f 00 00:00:28.973 READ FPDMA QUEUED 60 00 08 80 3f a0 40 00 00:00:28.973 READ FPDMA QUEUED 60 00 08 08 08 00 40 00 00:00:28.973 READ FPDMA QUEUED 25 00 08 00 48 a0 40 00 00:00:26.332 READ DMA EXT b0 da 00 00 4f c2 00 00 00:00:26.311 SMART RETURN STATUS
SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-71-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION === Model Family: Western Digital Caviar SE Serial ATA Device Model: WDC WD800JD-75MSA3 Serial Number: WD-WMAM9CXL5529 Firmware Version: 10.01E04 User Capacity: 80 000 000 000 bytes [80,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5625 ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sat Aug 16 23:34:15 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. See vendor-specific Attribute list for marginal Attributes.
General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2460) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 33) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported.
SMART Error Log Version: 1 ATA Error Count: 5 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 5 occurred at disk power-on lifetime: 32892 hours (1370 days + 12 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 45 4b 20 e9 Error: UNC at LBA = 0x09204b45 = 153111365
Error 4 occurred at disk power-on lifetime: 32846 hours (1368 days + 14 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 42 4b 20 e9 Error: UNC at LBA = 0x09204b42 = 153111362
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 06 42 4b 20 09 00 02:14:06.128 READ DMA 27 00 00 00 00 00 00 00 02:14:06.127 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 02:14:06.108 IDENTIFY DEVICE ef 03 46 00 00 00 00 00 02:14:06.108 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 02:14:06.107 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 3 occurred at disk power-on lifetime: 32846 hours (1368 days + 14 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 41 4b 20 e9 Error: UNC at LBA = 0x09204b41 = 153111361
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 01 41 4b 20 09 00 02:14:04.130 READ DMA 27 00 00 00 00 00 00 00 02:14:04.129 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 02:14:04.110 IDENTIFY DEVICE ef 03 46 00 00 00 00 00 02:14:04.110 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 02:14:04.109 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 2 occurred at disk power-on lifetime: 32846 hours (1368 days + 14 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 40 4b 20 e9 Error: UNC at LBA = 0x09204b40 = 153111360
Error 1 occurred at disk power-on lifetime: 32846 hours (1368 days + 14 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 40 4b 20 e9 Error: UNC at LBA = 0x09204b40 = 153111360
SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 10% 32889 153111360 # 2 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-71-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION === Model Family: Western Digital RE Serial ATA Device Model: WDC WD3200YS-01PGB0 Serial Number: WD-WCAPD5288794 Firmware Version: 21.00M21 User Capacity: 320 072 933 376 bytes [320 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5625 ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sat Aug 16 21:53:44 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check.
General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 111) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported.
SMART Error Log Version: 1 ATA Error Count: 3050 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 3050 occurred at disk power-on lifetime: 21059 hours (877 days + 11 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 00 18 f5 40 Error: UNC at LBA = 0x00f51800 = 16062464
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 da 00 00 18 f5 05 00 14d+19:27:57.467 READ DMA EXT 35 da 00 00 2a fd 05 00 14d+19:27:57.280 WRITE DMA EXT 35 da 00 00 28 fd 05 00 14d+19:27:57.077 WRITE DMA EXT 35 da 00 00 26 fd 05 00 14d+19:27:56.889 WRITE DMA EXT 35 da 00 00 24 fd 05 00 14d+19:27:56.694 WRITE DMA EXT
Error 3049 occurred at disk power-on lifetime: 21059 hours (877 days + 11 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 00 18 f5 40 Error: UNC at LBA = 0x00f51800 = 16062464
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 da 00 00 18 f5 05 00 14d+19:27:45.712 READ DMA EXT 25 da 00 00 12 ed 05 00 14d+19:27:45.711 READ DMA EXT 35 da 00 00 0c ff 05 00 14d+19:27:45.540 WRITE DMA EXT 35 da 00 00 0a ff 05 00 14d+19:27:45.353 WRITE DMA EXT 35 da 00 00 08 ff 05 00 14d+19:27:45.183 WRITE DMA EXT
Error 3048 occurred at disk power-on lifetime: 19737 hours (822 days + 9 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 80 c7 56 32 40 Error: UNC 128 sectors at LBA = 0x003256c7 = 3299015
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 da 80 c7 56 32 05 00 19d+15:42:00.783 READ DMA EXT 25 da 80 0f d1 34 0c 00 19d+15:42:00.772 READ DMA EXT 25 da 00 00 c0 31 05 00 19d+15:42:00.748 READ DMA EXT 25 da 80 c7 56 32 05 00 19d+15:41:58.398 READ DMA EXT 25 da 80 47 56 32 05 00 19d+15:41:58.397 READ DMA EXT
Error 3047 occurred at disk power-on lifetime: 19737 hours (822 days + 9 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 80 c7 56 32 40 Error: UNC 128 sectors at LBA = 0x003256c7 = 3299015
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 da 80 c7 56 32 05 00 19d+15:41:58.398 READ DMA EXT 25 da 80 47 56 32 05 00 19d+15:41:58.397 READ DMA EXT 25 da 47 00 56 32 05 00 19d+15:41:58.393 READ DMA EXT 25 da 39 c7 4f 32 05 00 19d+15:41:58.384 READ DMA EXT 25 da 39 c7 47 32 05 00 19d+15:41:58.382 READ DMA EXT
Error 3046 occurred at disk power-on lifetime: 19473 hours (811 days + 9 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 80 f7 de 29 40 Error: UNC 128 sectors at LBA = 0x0029def7 = 2744055
SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-71-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Black Device Model: WDC WD5000BEKT-00KA9T0 Serial Number: WD-WXE1A2152607 LU WWN Device Id: 5 0014ee 205b0d959 Firmware Version: 01.01A01 User Capacity: 500 107 862 016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5625 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Aug 17 16:57:41 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check.
General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10380) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 122) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported.
SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-71-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION === Model Family: Seagate Momentus 7200.3 Device Model: ST9320421ASG Serial Number: 5TJ0H4N3 LU WWN Device Id: 5 000c50 0123c8e51 Firmware Version: SD13 User Capacity: 320 072 933 376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5625 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Aug 17 16:59:04 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. See vendor-specific Attribute list for marginal Attributes.
General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 90) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported.
SMART Error Log Version: 1 ATA Error Count: 6 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 6 occurred at disk power-on lifetime: 6418 hours (267 days + 10 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 88 5a 1e 01 Error: UNC at LBA = 0x011e5a88 = 18766472
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 ff 37 68 5a 1e e1 00 00:01:30.134 READ DMA EXT 25 ff 37 68 5a 1e e1 00 00:01:27.244 READ DMA EXT 25 ff 37 68 5a 1e e1 00 00:01:24.463 READ DMA EXT 25 ff 09 5f 5a 1e e1 00 00:01:24.462 READ DMA EXT 25 ff 36 29 5a 1e e1 00 00:01:24.461 READ DMA EXT
Error 5 occurred at disk power-on lifetime: 6418 hours (267 days + 10 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 88 5a 1e 01 Error: UNC at LBA = 0x011e5a88 = 18766472
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 ff 37 68 5a 1e e1 00 00:01:27.244 READ DMA EXT 25 ff 37 68 5a 1e e1 00 00:01:24.463 READ DMA EXT 25 ff 09 5f 5a 1e e1 00 00:01:24.462 READ DMA EXT 25 ff 36 29 5a 1e e1 00 00:01:24.461 READ DMA EXT 25 ff 0a 1f 5a 1e e1 00 00:01:24.461 READ DMA EXT
Error 4 occurred at disk power-on lifetime: 6418 hours (267 days + 10 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 88 5a 1e 01 Error: UNC at LBA = 0x011e5a88 = 18766472
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 ff 37 68 5a 1e e1 00 00:01:24.463 READ DMA EXT 25 ff 09 5f 5a 1e e1 00 00:01:24.462 READ DMA EXT 25 ff 36 29 5a 1e e1 00 00:01:24.461 READ DMA EXT 25 ff 0a 1f 5a 1e e1 00 00:01:24.461 READ DMA EXT 25 ff 18 07 5a 1e e1 00 00:01:24.459 READ DMA EXT
Error 3 occurred at disk power-on lifetime: 6418 hours (267 days + 10 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 88 5a 1e 01 Error: UNC at LBA = 0x011e5a88 = 18766472
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 ff 37 68 5a 1e e1 00 00:00:37.275 READ DMA EXT 25 ff 37 68 5a 1e e1 00 00:00:34.390 READ DMA EXT 25 ff 08 47 25 15 e1 00 00:00:21.974 READ DMA EXT 25 ff 08 3f 25 15 e1 00 00:00:21.968 READ DMA EXT c8 ff 02 79 1c 60 e0 00 00:00:21.955 READ DMA
Error 2 occurred at disk power-on lifetime: 6418 hours (267 days + 10 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 88 5a 1e 01 Error: UNC at LBA = 0x011e5a88 = 18766472
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 ff 37 68 5a 1e e1 00 00:00:34.390 READ DMA EXT 25 ff 08 47 25 15 e1 00 00:00:21.974 READ DMA EXT 25 ff 08 3f 25 15 e1 00 00:00:21.968 READ DMA EXT c8 ff 02 79 1c 60 e0 00 00:00:21.955 READ DMA 25 ff 08 37 77 db e1 00 00:00:21.954 READ DMA EXT
SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 28259 - # 2 Short offline Completed without error 00% 28250 - # 3 Extended offline Completed without error 00% 28201 - # 4 Short offline Completed without error 00% 19465 -
SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-71-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue Serial ATA Device Model: WDC WD1600AAJS-75M0A0 Serial Number: WD-WMAV38910013 LU WWN Device Id: 5 0014ee 00192cb76 Firmware Version: 02.03E02 User Capacity: 160 000 000 000 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5625 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Sun Aug 17 16:47:16 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check.
General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3000) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 39) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported.
SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-71-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION === Model Family: Western Digital Caviar SE Serial ATA Device Model: WDC WD800JD-75MSA3 Serial Number: WD-WMAM9CYY0450 Firmware Version: 10.01E04 User Capacity: 80 000 000 000 bytes [80,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5625 ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sun Aug 17 16:16:25 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. See vendor-specific Attribute list for marginal Attributes.
General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2460) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 33) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported.
SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-71-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K1000.B Device Model: Hitachi HDT721016SLA380 Serial Number: STA0D7MB3PPLJF LU WWN Device Id: 5 000cca 345f42361 Firmware Version: ST1OA38E User Capacity: 160 000 000 000 bytes [160 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5625 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Aug 17 11:38:56 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check.
General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2371) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 40) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported.
SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-71-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F3 Device Model: SAMSUNG HD103SJ Serial Number: S246J9EB915290 LU WWN Device Id: 5 0024e9 20630cd5a Firmware Version: 1AJ10001 User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5625 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Aug 16 23:31:12 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check.
General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9300) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 155) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported.
SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more