Brand new aftermarket Stator + Spped Sensor Kit

Direct replacement to your original unit

Highest grade of lamination materials

Connector included

Rubber grommet included

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Please Note There are two possible stators for most of the Outlander models from 2016 through 2019. This stator is only for the standard packages. For all the other packages, please refer to RMS010-106349.

Brand new aftermarket Stator + Speed Sensor Kit

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• All product shipped are tested

Brand new aftermarket stator

• Highest grade of lamination materials
• Highest grade of copper winding, resistant to 200 degrees Celsius
• Connector included
• Rubber grommet included

Can-Am Outlander 1000 -- 2012
Can-Am Outlander 330 -- 2005
Can-Am Outlander 400 -- 2003-2015
Can-Am Outlander 450 -- 2018-2020
Can-Am Outlander 450 T3 EFI F/C -- 2018-2019
Can-Am Outlander 500 -- 2007-2015
Can-Am Outlander 500 XT -- 2007-2009
Can-Am Outlander 570 -- 2017-2020
Can-Am Outlander 570 T3 Pro Nordic EFI L/C -- 2019
Can-Am Outlander 650 EFI -- 2006-2012, 2014-2020
Can-Am Outlander 650 T3 EFI F/C -- 2019
Can-Am Outlander 650 XT -- 2006-2009
Can-Am Outlander 800 -- 2006
Can-Am Outlander 800 R -- 2007-2015
Can-Am Outlander 800 R XT -- 2009
Can-Am Outlander 800 XT -- 2006
Can-Am Outlander L 450 -- 2016
Can-Am Outlander L 570 -- 2016
Can-Am Outlander L Max 450 -- 2016
Can-Am Outlander L Max 570 -- 2016
Can-Am Outlander Max 400 -- 2004-2015
Can-Am Outlander Max 450 -- 2018-2020
Can-Am Outlander Max 450 T3 EFI F/C -- 2019
Can-Am Outlander Max 500 -- 2007-2015
Can-Am Outlander Max 500 XT -- 2008-2009
Can-Am Outlander Max 570 -- 2016-2020
Can-Am Outlander Max 650 -- 2006-2021
Can-Am Outlander Max 650 T3 EFI F/C -- 2019
Can-Am Outlander Max 650 XT -- 2006-2009
Can-Am Outlander Max 800 -- 2007
Can-Am Outlander Max 800 R -- 2009-2013, 2015
Can-Am Outlander Max 800 XT -- 2007
Can-Am Renegade 1000 -- 2014-2015
Can-Am Renegade 1000R -- 2016-2019
Can-Am Renegade 500 -- 2008-2015
Can-Am Renegade 570 -- 2016-2020
Can-Am Renegade 650 T3 EFI F/C -- 2019
Can-Am Renegade 800 -- 2007-2008
Can-Am Renegade 800 R -- 2009-2011, 2013-2015
Can-Am Renegade 850 -- 2016-2019
Can-Am Renegade X 800 -- 2008

106953--R00

Stator's Dimensions:
Interior diameter: 41 mm
Exterior diameter: 104 mm
Thickness: 30 mm Length of wires stator to grommet : 140 mm
Length of wires grommet to plug : 850 mm

Other specifications:
Number of wires: 3
Number of plugs: 1
Number of terminals: 3

Wire to wire resistance:
Alternator: Yellow between each Yellow = 0.4 ohms +/-20%

Speed sensor's Dimensions:
Width: 19 mm
Length: 50 mm
Height: 37 mm
Wires length: 350 mm

Other specifications:
Number of plugs: 1
Number of terminals: 3

Before installing your new stator

• Check the AC output of the stator.
• Replace any burned or corroded connectors on stator and regulator/rectifier
• Check and repair any melted wiring.
• Use hi-temp dielectric grease on all connectors

Our stator may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.

When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010".

Speed Sensor

Direct replacement to your original unit

Warning:

Risk of electric shock. Disconnect the battery before servicing.
Ensure proper installation by a qualified technician to avoid malfunction.