QUARTZO FERRARI 312 T2 F1 1976 BELGIAN GP #2 REGAZZONI 1:43 RESIN MODEL Q4068


Superbly detailed 1:43 scale (10cm long) resin and plastic model by Portuguese brand Quartzo. Authentic race livery and sponsor logos, rubber tyres, detailed engine, suspension, transmission & exhaust system, painted driver with authentic helmet. Wheels rotate although the model is intended for static display.


The Ferrari 312T was a Ferrari Formula One car design, based on the 312B3 from 1974. In various versions, it was used from 1975 until 1980. It was designed by Mauro Forghieri for the 1975 season, and was an uncomplicated and clean design that responded well to mechanical upgrades.


The 312T series won 27 races, four Constructors' and three Drivers' Championships, making it the most successful car design in Formula One history. It was replaced for the 1981 season by the 126 C, Ferrari's first turbocharged F1 car. It was also Ferrari's last naturally-aspirated F1 car until the Ferrari 640 in 1989, after the ban on turbocharged engines.


The car was powered by the powerful and reliable Tipo 015 flat-12 engine which gave around 510 bhp. Although it had to carry more fuel, oil and water than the Cosworth DFV-powered cars the power-to-weight ratio of the flat-12 was about the same as the DFV. The "3" stood for the car's engine displacement (3 litres) and "12" was the number of cylinders it had (12).


In order to improve upon the preceding 312B3, Forghieri designed a new chassis for the 312T. The 312T chassis was a semi-monocoque consisting of tubular spaceframe reinforced with riveted aluminium panels. This "traditional" construction was a departure from the full monocoque of the 312B3. The new chassis was slightly heavier than the 312B3 monocoque, but had comparable rigidity and was easier to adjust and repair. It could also accept bodywork with a lower frontal area, reducing drag. The suspension design was substantially revised to work with the new chassis. The same basic chassis design and construction method was used in all 312T-series cars, although later cars received modifications to improve torsional rigidity.


Forgheri and Ferrari engineer Walter Salvarani also developed a new gearbox for the 312T. This unit was mounted behind the engine in a transverse orientation, ahead of the rear wheels. This moved the car's center of mass forward and lowered the polar moment of inertia. This design had precedent in the March 721X.   This gearbox configuration was considered so important to the overall design that the "T" in the 312T name stood for trasversale, Italian for transverse. While all 312T gearboxes used in competition were conventional manual transmissions, Ferrari briefly experimented with a semi-automatic version of the gearbox in 1979. This consisted of a modified version of the manual gearbox actuated by a high-pressure hydraulic system, controlled by buttons mounted on the steering wheel. The system was intended to speed up gear changes and reduce human error. It was tested by Scuderia Ferrari driver Gilles Villeneuve at Fiorano, but was not used in competition as Villeneuve preferred the original manual transmission. Ferrari would revisit the semi-automatic gearbox 10 years later, in the 1989 Ferrari 640 F1 car.


The Formula 1 technical regulations were changed for the 1976 season – from the Spanish Grand Prix in May, the tall air boxes which had become popular would be banned. The rules therefore allowed Ferrari to continue to use the 312T for the opening 3 races of the 1976 season (Lauda won the first two and Regazzoni the third), before the introduction of its successor, a revised version called the 312T2.


The 312T2 was launched at Fiorano and featured a number of modifications over the 312T. In order to comply with the revised aerodynamic rules, the car no longer featured an airbox behind the cockpit. Instead "NACA shaped" air intakes were incorporated into the cockpit sides, feeding air into each cylinder bank of the flat 12 engine. At 2560mm, the wheelbase was 42mm longer than that of the 312T. At the time of launch, the car also featured some notable mechanical modifications, including a de Dion rear suspension arrangement, although this was abandoned after extensive testing, in favour of a more conventional suspension set up.


The 312T2 was given its race debut at the non-championship Brands Hatch Race of Champions in March 1976 and was first used in a world championship race in May at the Spanish Grand Prix. The 312T2 was, if anything, more successful than the 312T. Lauda was comfortably leading the world championship after another 3 wins, when at the 1976 German Grand Prix at Nürburgring he had a massive accident caused by a suspected rear suspension failure. In the aftermath he nearly burned to death, but was miraculously back to racing just 6 weeks later. Lauda conceded the title by just a single point to James Hunt, but the 312T2's superiority helped Ferrari win its second consecutive constructors' title.


Quartzo was a brand name used by the Portuguese Vitesse group for 1/43rd scale models of NASCAR racing cars, historical touring cars and historical Formula 1 cars in the 1990s. Like most later Vitesse models, Quartzo models were made in China, and they are very well detailed. The Vitesse group ceased production in summer 2001, but Sun Star, who had already reactivated the Vitesse brand name in 2003, also introduced a new Quartzo range consisting of 1/18th scale Formula 1 cars in 2005.


🚛+🛵+✈️+🏎️=1x📦 Combined shipping is available for all items (even if you’re not in the UK). Please add each item to your 🛒 basket or request an invoice before paying. If Ebay’s Global Shipping Programme is trying to charge you shipping per item, I can create a unique listing from you with all your items combined. For offers with instant payment on acceptance, any overpaid postage will be refunded. Items will be carefully and safely packed for shipping ensuring that the box and its contents are well protected.