[Note] Please confirm that your ECU socket is consistent with the picture provided by me before purchasing.
[Note] The motorcycles with carburetor can not be used.
This gear indicator is only suitable for Electronic Fuel Injected(EFI) Motorcycles NOT Carburetor Fuel Injected.The motor with ABS are connected to 3-4 lines. It can be directly connected.  
For the return of order due to the above reasons, the buyer will pay the return fees.
 
 
Features:
Easy for installation, paste it around dashboard with double-sided adhesive tape
Plug and play, original car with reserved socket for quick connection, no need cut lines
Reads ECU data of motorcycle only, won't cause any damage
Super waterproofing, even soaked in water would be fine
Gears display once the engine working and clutch released

Specification:
LED Light:Red
Application: Honda EFI Motorcycles
Color: black housing
Size: about 30mm *20mm *13mm( L* W* T) Cable length: 170cm

Applicable Models:
[Note]
Cannot be used: Honda CBR F4I cannot be used

For Honda CB250F(with digital trip/odo) 2015
For Honda CB300F 2015-2018
For Honda CB400SF 2008-2017
For Honda CB400X 2013-2016
For Honda CB400F 2013-2015
For Honda CB500F 2013-2018
For Honda CB500X 2013-2018
For Honda CB600F Hornet 2007-2013
For Honda CB650F 2014-2018
For Honda CB1000R 2008-2018
For Honda CB1100 (non-ABS) 2010-2016
For Honda CB1100 (ABS) 2010-2016
For Honda CB1300 S/F 2003-2015
For Honda CBF600 2008-2012
For Honda CBF1000 F/FA 2006-2009
For Honda CBR250R 2015
For Honda CBR300R 2015-2019
For Honda CBR400R 2013-2015
For Honda CBR500R 2013-2018
For Honda CBR600F 2011-2013
For Honda CBR600RR 2 003-2018
For Honda CBR1000RR 2 004-2018
For Honda CBR650F 2014-2018
For Honda CMX300 Rebel 2018-2019
For Honda CMX500 2018-2019
For Honda CRF250L/M All Years
For Honda Crossrunner All Years
For Honda CTX700 (w/o DTC) 2014-2018
For Honda Fury 2010-2018
For Honda Interstate 2010-2016
For Honda NC400X 2013-2015
For Honda NC700 S/X 2012-2018
For Honda NC750 S/X 2014-2018
For Honda NT700V Deauville 2006-2015
For Honda Sabre 2010-2012
For Honda Stateline 2010-2018
For Honda VFR800 interceptor 2005-2013
For Honda VFR800X All Years
For Honda VT400 (FI model) 2009-2014
For Honda VT750C (FI model shadow 750) 2007-2017
For Honda VT750S (FI model shadow 750) 2007-2009
For Honda VT1300 (All) 2010-2016
For Honda VTX1800 2005-2012
For Honda XL125V Varadero 2007-2014
For Honda XL700V Transalp (non-ABS) 2008-2014
For Honda XL700V Transalp (ABS) 2008-2014
For Honda XL1000V Varadero 2003-2012
For Honda TRX ATVs (FI model) All Years    
FOR CB300R2018-2019    
FOR  GL1800 2005-2017
FOR CTX1300 2014-2015
FOR ST1300 2008-2015
FOR VTR250 2009-2014

Package:
Gear Indicator
Double-sided Adhesive Tape
Cable Ties
User Manual

Installation Steps:
You need to setup this module after installation.Perform the setup only when the engine is WARM so the idle speed is normal,Find a long,straight road with light traffic.The unit does not learn the same gear twice,this makes it easy to set up on the road. You can even shift down and stop during the setup if needed.Do not stare at the display,watch the road and ride with extreme care as always! Turn the ignition On.The display counts backwards(6 to 1)indicating that the memory is clear. When "L" is flashing,stare the engine in Neutral and let the engine idle.When the display is flashing "1",select second gear. Release the clutch and stare riding normally.The display is blinking faster while the unit is learning the gear. When the display show "n"(next),select second gear.Repeat this process until all gears are thought.In top gear,wait until "o"(over) is indicated and the display stops blinking. The unit is now programmed and should indicate all gears correctly.When ignition is turned on,the display counts forward(1 to 6) indicating that it is programmed and fully functional.
Rest:
If some gears are not indicated correctly, reset the unit and set it up again.If you change your gearing (install new front or rear sprocket),or you install a speedometer (or other speedometer calibrator),probably you will have to reset it and set it up again. Cut off the power of the unit 6 times in a row,while the display is counting up and shows3 ,4 or 5. You can power on/off the display by turning the ignition key on/off.On the next power up,the display will count backwards(6 to 1). The memory is clear now and you can perform the Setup procedure.