It describes the Taiwan Province Strait in 2023. The 052DL guided missile destroyer Suzhou, with the ship number 132 of the East China Sea Fleet of the China Navy, intercepted the scene of the US military Alibek-class DDG93 Gordon pai' ea chung-hoon. The perspective is released from a seahawk helicopter. (The anti-ship missile in the launching state in the seal painting is only a special effect piece that proves that the kit contains this state.)
Suzhou ship cut into the route from the left rear of the American ship at a speed of over 30 knots, with the shortest distance of only 137 meters, and completed two interception actions (left front to right front, right front to left front). In the end, the American ship reduced its speed to ten knots and actively turned to avoid it.
The third batch of 052DL model produced in 2020 has the following main changes compared with the previous 052D model:
Radar upgrade: replace YLC-8B long-range early warning radar (improving the ability to detect stealth targets) and 368 X-band radar (increasing the detection distance of low-altitude targets to 500 kilometers).
Hull optimization: the stern is extended by 5 meters, and the helicopter deck can take off and land the straight -20F anti-submarine helicopter, so the anti-submarine capability is significantly enhanced.
Weapon adaptation: the vertical firing system is compatible with Eagle Strike -21 hypersonic missile (with a range of 1,500 kilometers), and the anti-ship capability is improved by leaps and bounds.
Glue-free color separation The integral hull, the red below the waterline of the hull is made by pre-injection technology. The main gun is made of plastic parts and the 3D printed naval gun with better details can be replaced with each other. Attached is a vertical smoke screen special effect piece, which can be installed with Eagle Strike 21 anti-ship missile 1130 near-anti-gun, which restores exquisite details and can be assembled to the hull without glue
Completely new mold
-Pre-painted parts included
・No adhesive or painting required
- Painted etched parts
- The missile launch system (ULS) is made of PVC
・The bridge is molded as a single piece for easy assembly
- Main guns and helicopters are realistically reproduced using 3D printed parts
- The anti-corrosion coating on the hull is also realistically reproduced.
- The hull is made of a single piece of molding to reduce the number of parts and make assembly easier.
・No adhesive or painting required
- Painted etched parts
- The missile launch system (ULS) is made of PVC
・The bridge is molded as a single piece for easy assembly
- Main guns and helicopters are realistically reproduced using 3D printed parts
- The anti-corrosion coating on the hull is also realistically reproduced.
- The hull is made of a single piece of molding to reduce the number of parts and make assembly easier.
Glue-free color separation The integral hull, the red below the waterline of the hull is made by pre-injection technology. The main gun is made of plastic parts and the 3D printed naval gun with better details can be replaced with each other. Attached is a vertical smoke screen special effect piece, which can be installed with Eagle Strike 21 anti-ship missile 1130 near-anti-gun, which restores exquisite details and can be assembled to the hull without gl
warning
Due to the product is a professional assembled model that requires glue and painting after completion, However, paint and glue is flammable and explosive, please store it in a safe place
It describes the Taiwan Province Strait in 2023. The 052DL guided missile destroyer Suzhou, with the ship number 132 of the East China Sea Fleet of the China Navy, intercepted the scene of the US military Alibek-class DDG93 Gordon pai' ea chung-hoon. The perspective is released from a seahawk helicopter. (The anti-ship missile in the launching state in the seal painting is only a special effect piece that proves that the kit contains this state.)
Suzhou ship cut into the route from the left rear of the American ship at a speed of over 30 knots, with the shortest distance of only 137 meters, and completed two interception actions (left front to right front, right front to left front). In the end, the American ship reduced its speed to ten knots and actively turned to avoid it.
The third batch of 052DL model produced in 2020 has the following main changes compared with the previous 052D model:
Radar upgrade: replace YLC-8B long-range early warning radar (improving the ability to detect stealth targets) and 368 X-band radar (increasing the detection distance of low-altitude targets to 500 kilometers).
Hull optimization: the stern is extended by 5 meters, and the helicopter deck can take off and land the straight -20F anti-submarine helicopter, so the anti-submarine capability is significantly enhanced.
Weapon adaptation: the vertical firing system is compatible with Eagle Strike -21 hypersonic missile (with a range of 1,500 kilometers), and the anti-ship capability is improved by leaps and bounds.
Glue-free color separation The integral hull, the red below the waterline of the hull is made by pre-injection technology. The main gun is made of plastic parts and the 3D printed naval gun with better details can be replaced with each other. Attached is a vertical smoke screen special effect piece, which can be installed with Eagle Strike 21 anti-ship missile 1130 near-anti-gun, which restores exquisite details and can be assembled to the hull without glue
Completely new mold
-Pre-painted parts included
・No adhesive or painting required
- Painted etched parts
- The missile launch system (ULS) is made of PVC
・The bridge is molded as a single piece for easy assembly
- Main guns and helicopters are realistically reproduced using 3D printed parts
- The anti-corrosion coating on the hull is also realistically reproduced.
- The hull is made of a single piece of molding to reduce the number of parts and make assembly easier.
・No adhesive or painting required
- Painted etched parts
- The missile launch system (ULS) is made of PVC
・The bridge is molded as a single piece for easy assembly
- Main guns and helicopters are realistically reproduced using 3D printed parts
- The anti-corrosion coating on the hull is also realistically reproduced.
- The hull is made of a single piece of molding to reduce the number of parts and make assembly easier.
Glue-free color separation The integral hull, the red below the waterline of the hull is made by pre-injection technology. The main gun is made of plastic parts and the 3D printed naval gun with better details can be replaced with each other. Attached is a vertical smoke screen special effect piece, which can be installed with Eagle Strike 21 anti-ship missile 1130 near-anti-gun, which restores exquisite details and can be assembled to the hull without gl
On Jan 14, 2026 at 02:47:37 PST, seller added the following information: