• Features:
  •  
    • Fits LH (Driver Side) & RH (Passenger Side) Front
    • Fits 5 Lugs Models
     
  • Item Description:
  •  
    • Brand New Wheel Hub Bearing Steering Knuckle Assembly
    • Direct replacement
    • Built to strict quality control standards
    • Replaces dealer part numbers: 698-464, 698464, 5172038110, 5175039603, 517163R010, 517563R000, SK698464, WLK464, 698-465, 698465, 5172038110, 5175039603, 517153R010, 517553R000, SK698465, WLK465
     
  • Applicable Models:
  •  
    • For Hyundai Sonata 2011-2013 2.4L | 14mm Camber Bolt Holes | Except Sport Suspension
    Package Includes:
  •  
  • 2 PCS Front Wheel Hub Bearing Knuckles For Hyundai Sonata 2.4L 2011 2012 2013

    Features:

     

    • Fits LH (Driver Side) & RH (Passenger Side) Front
    • Fits 5 Lugs Models

     

    Item Description:

     

    • Brand New Wheel Hub Bearing Steering Knuckle Assembly
    • Direct replacement
    • Built to strict quality control standards
    • Replaces dealer part numbers: 698-464, 698464, 5172038110, 5175039603, 517163R010, 517563R000, SK698464, WLK464, 698-465, 698465, 5172038110, 5175039603, 517153R010, 517553R000, SK698465, WLK465

     

    Applicable Models:

     

    • For Hyundai Sonata 2011-2013 2.4L | 14mm Camber Bolt Holes | Except Sport Suspension

    Package Includes:

     

    • (2) Steering Knuckles Wheel Hub Bearings (LH & RH)

     

    NOTE:

     

    • Failure to separate the front wheel sensor from the steering knuckle may result in damage to the front wheel sensor;
    • Pull out the front wheel sensor, being careful to turn it as little as possible.
    • Do not pull on wheel sensorharness.

     

    Inspection after removel : Check components for deformationy,cracksy,and other damagey,and  boots of transverse link ball joint for cracksy,axial end play,and swing torque. 

     

    Installation:

     

    Installation is in the reverse order of the removal

     

    Caution:

     

    1. Do not reuse the wheel stud.
    2. Do not reuse the cotter pin.
    3. Place a washer (A) as shown to install the wheel studs (1) by using the tightening force of the nut (B).
    4. Clean the mating surfaces of the joint sub-assembly and the wheel hub and bearing. Apply lubricant to the surface (A) of the joint sub-assembly.
    5. Hold the wheel hub and bearing using a suitable tool. Tighten the wheel hub lock nut

     

     

        6. Since the drive shaft is assembled by press-fitting, use a torque wrench to tighten the wheel hub lock nut. Do not use a power tool.

        7. Too much torque causes axle noise. Too little torque causes wheel bearing looseness. Tighten the wheel hub lock nut to the specification.

        8.  When installing a the cotter pin (1) and the nut retainer (2), securely bend the cotter pin to prevent rattles.

        9. Align the matching marks (A) on the disc brake rotor and on the wheel hub and bearing.



    Payment

    We will only ship to the confirmed shipping address given with the payment.

    We do not offer local pickups.

    Shipping

    1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)

    2. The images shown are not the actual item and are for your reference only.

    3. Fast shipping:All our packages use USPS Package Service

    4. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!

    Returns

    1. You have 7 days to contact us and 10 days to return it from the date it was received.

    2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.

    3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.

    Contact Us

    We are always been trying to provide best service and reliable products for every customer.


    If you are satisfed with the product you recieved,please leave us positive feedback.


    If you are not satisfied for any reason, please do not be quick to leave negative or neutral feedback.We will work hard to make sure every customer 100 percent satisfied, and reslove any problem for you.

    Shop Category
    2 PCS Front Wheel Hub Bearing Knuckles For Hyundai Sonata 2.4L 2011 2012 2013

    Features:

     

    • Fits LH (Driver Side) & RH (Passenger Side) Front
    • Fits 5 Lugs Models

     

    Item Description:

     

    • Brand New Wheel Hub Bearing Steering Knuckle Assembly
    • Direct replacement
    • Built to strict quality control standards
    • Replaces dealer part numbers: 698-464, 698464, 5172038110, 5175039603, 517163R010, 517563R000, SK698464, WLK464, 698-465, 698465, 5172038110, 5175039603, 517153R010, 517553R000, SK698465, WLK465

     

    Applicable Models:

     

    • For Hyundai Sonata 2011-2013 2.4L | 14mm Camber Bolt Holes | Except Sport Suspension

    Package Includes:

     

    • (2) Steering Knuckles Wheel Hub Bearings (LH & RH)

     

    NOTE:

     

    • Failure to separate the front wheel sensor from the steering knuckle may result in damage to the front wheel sensor;
    • Pull out the front wheel sensor, being careful to turn it as little as possible.
    • Do not pull on wheel sensorharness.

     

    Inspection after removel : Check components for deformationy,cracksy,and other damagey,and  boots of transverse link ball joint for cracksy,axial end play,and swing torque. 

     

    Installation:

     

    Installation is in the reverse order of the removal

     

    Caution:

     

    1. Do not reuse the wheel stud.
    2. Do not reuse the cotter pin.
    3. Place a washer (A) as shown to install the wheel studs (1) by using the tightening force of the nut (B).
    4. Clean the mating surfaces of the joint sub-assembly and the wheel hub and bearing. Apply lubricant to the surface (A) of the joint sub-assembly.
    5. Hold the wheel hub and bearing using a suitable tool. Tighten the wheel hub lock nut

     

     

        6. Since the drive shaft is assembled by press-fitting, use a torque wrench to tighten the wheel hub lock nut. Do not use a power tool.

        7. Too much torque causes axle noise. Too little torque causes wheel bearing looseness. Tighten the wheel hub lock nut to the specification.

        8.  When installing a the cotter pin (1) and the nut retainer (2), securely bend the cotter pin to prevent rattles.

        9. Align the matching marks (A) on the disc brake rotor and on the wheel hub and bearing.



    We will only ship to the confirmed shipping address given with the payment.

    We do not offer local pickups.

    1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)

    2. The images shown are not the actual item and are for your reference only.

    3. Fast shipping:All our packages use USPS Package Service

    4. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!

    1. You have 7 days to contact us and 10 days to return it from the date it was received.

    2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.

    3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.

    We are always been trying to provide best service and reliable products for every customer.


    If you are satisfed with the product you recieved,please leave us positive feedback.


    If you are not satisfied for any reason, please do not be quick to leave negative or neutral feedback.We will work hard to make sure every customer 100 percent satisfied, and reslove any problem for you.


    Copyright of autoutdoor. All rights reserved.