Hot Tub Fix A Leak Leak Sealer Single 8 Oz Bottle HTCPFAL-08

Hot Tub Replacement Part Fix A Leak Hot Tub Leak Sealer

This is for a Single 8 Oz Bottle of Hot Tub Fix A Leak Chemicals Hot Tub Leak Sealer
High Quality that's made to last!!

General Directions for Using Fix A Leak.
Fix A Leak is a heavy suspension and must be shaken thoroughly, before use. The filter must be bypassed, in order to prevent the Fix A Leak, from being filtered out. Set the multiport valve to recirculate. If this cannot be done, with a D.E. or cartridge filter, simply remove the D.E. Filter element or filter cartridge and allow the water to flow through the empty filter tank. Fix A Leak should be added to the skimmer, main drain or other water intake, while the pump is running, in recirculate mode. For suction leaks, characterized by an aerated return flow, refer to the directions below. Because Fix A Leak is so heavy, it will tend to sink to the floor, upon returning to the pool or spa. Set the water intake to close off the skimmers and use only the main drain. If there is no main drain, attach the pool vacuum to a skimmer and set in the deep end or center of the pool. Brush occasionally, about every 3-4 hours, while the pump is running, to help keep the product in suspension. Run the pump continuously, until there is an indication that the leaking has stopped. To monitor progress, make the water level with a piece of tape. Check daily for 2-4 days, while maintaining pump operation and occasional brushing. Some small water losses can be attributed to evaporation, so compare the losses before and after the Fix A Leak addition. Once the leak appears to have been stopped, make sure that you allow 2-4 days for the product to cure. Fix A Leak forms a crust, as it is carried out with the leaking water. This is what makes the seal. It has to completely dry out, to cure to a long-lasting seal. Normal filter operation can resume, after the leak has been determined to have been stopped. This leak-sealing crust forms on the outside of the pool, spa shell or pipes. Draining of the pool or spa is not necessary. The excess Fix A Leak will be removed, with the resumption of normal filtration and the vacuuming and/or brushing of the pool or spa floor. Return the multiport valve to the filtering position and resume filtration. Backwash daily for the next 2-3 days, while brushing the floor. Cartridge filters should be cleaned daily, for the next 2-3 days, while brushing the floor occasionally. Never allow the wet cartridge dry out, without a complete cleaning rinse, D.E. filters resume normal operation, brush or vacuum the pool floor and clean the filter out in 2-3 days or if the pressure rises too high. Don't allow the filter grids to dry out, before completely rinsing free of the removed excess Fix A Leak.

Spa Leaks or Hot Tub Leaks.
Remove the filter cartridge, which will effectively be the same as bypassing the filter. Shake the Fix A Leak very well, to help restore its suspension. The Fix A Leak product is very concentrated and heavy. It will quickly sink to the spa floor, unless stirred up with a broom, in addition to maintaining circulation. The product should be slowly added to the skimmer or other type of water intake. Recirculate and brush the spa floor, until it appears that the leaking has stopped. After the leaking has stopped, allow 2-4 days, for the product to dry out and cure. If there are signs of wet insulation, it should be removed, to facilitate the drying out and curing process. At this point, either drain and thoroughly clean the spa, with a wet, non-abrasive towel or resume filtration. If choosing the latter, brush the spa floor and hose-clean the spa filter cartridge a few times, over the next several days. Never allow a filter cartridge, that has been used to remove the excess Fix A Leak, to dry out, before thoroughly cleaning and hosing off. Allow the underside to dry out for 3-5 days. Open the cabinet and use a fan to ventilate the underside, to help with the drying out and curing.

High Quality that's made to last!!

Returns & Return Policy

Returns: You have 30 days to return your purchase for any reason and you have 14 days to report a damaged purchase or not as described please return the item in original package make sure its protected as not to be damaged while shipping insure item as necessary as you are responsible till we receive it. You are responsible for return shipping cost unless otherwise you are instructed that we will be providing you with a prepaid label. We need to receive item no later than 15 days from the date of this email as soon as we receive the item and inspect if it meets our return policy you will be refunded per our refund policy.NOTE: If the item is damaged has been used or we can not resell or you send back an item we did not sell to you or purchase is returned late. You may be charged a restocking fee for up to 50% of cost or return can be denied per our policy. If we pay your return shipping for other than if the item is being returned as defective or damaged we will deduct shipping from your purchase amount. Return to Diy Part Center P.O. Box 1686 Higley Arizona 85236
If item is being returned because the claim is item is defective or damaged once we receive item and it is tested and or checked for damage and item is found to be defective and damage was not caused by improper use we will credit your account or resend a replacement who pays for shipping will be determined at that time if you what a replacement and want a replacement faster you must reorder and pay for it then we will credit return after we receive and inspect return .

Spa Covers, Chemicals, Paint, and other "Custom" orders are not refundable; please call for details.
Shipping and Handling charges are non-refundable.

Note: we will not accept returns that have postage due these will be returned back to you from the shipping company. Please do not add signature required as this will delay your refund as we only pick up packages with signature required once a week your tracking information should tell you in most cases when we receive your return.

If you are returning an item because it was a lower cost somewhere else and the item we send you is an Oem part which is from the manufacturer please follow the direction for this return.
[Important]Good day the item you received is an Oem part from the manufacturer the part that you have purchased from a different location may be an aftermarket part .as not to confuse our part with the other we ask you to return our unopened Oem part in its original package if item is open or part is not what we had sent you per our policy we can deny the return or deduct up to 50% of cost as a restock fee or in this case we would have to dispose of part . If the item is unopened in original package nothing to worry about you will receive a full refund thank you for your understanding Sam
All items being returned not as described must describe what is not as described this must be a critical part off description example wrong color, wrong size, a different picture of an item then what you received. These returns will not be honored as not as described if it doesn't meet these criteria and buyer will pay for return shipping.

Please to not return items that have not been authorized to return as we are unable in some cases to refund item after 30 days you will be responsible to provide returned prepaid label.

We offer returns up to 30 days after you received your product. Before you ship your product back give us a call or email us. We will issue you a unique number to make sure your product does not get lost and you’re refunded quickly.