California Proposition 65: WARNING: This product has not been tested for chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov

All parts are new aftermarket replacement parts manufactured by Cougars Unlimited LLC and come with a 2-year limited factory warranty. They are replacement parts to be used to replace the original Ford parts. This switch is made in the USA.

You are purchasing one

C9WB-14488-P Starter Solenoid Pigtail Set Harness repair kit

Application:

1969 1970 XR7 Cougar

Parts included

1-C9WB-14462-AR Red with Blue overmolded ring Low-Fuel wire

1-C7AB-14488-R Red/Blue starter wire

1-C7AB-14488-B Brown starter wire

1-C9AZ-14526-ER Black 16 ga Fusible link wire (Must be crimped – Do not solder)

This kit is used to replace the damaged or missing ends of the existing harness that attaches these four wires (11 inches) to the starter solenoid. Cut off the ends of the existing harness and either crimp on or solder the new wires on. NOTE: fusible links cannot be soldered, they must be crimped.

Extensive research has been put into the choosing of proper connectors, gauge of wires, industrial grade connectors and electronic components. They are nice! All aspects of the manufacturing process from design to testing are overseen by an electronic engineer with over 40 years of experience, as a result these units the most robust and reliable units on the market.

Cougars Unlimited LLC manufactures sequential turn signal systems for 1967-1973 Cougar and 1965-1971 Thunderbird and 1968-1970 Mustang Shelby. Since 1981 Cougars Unlimited has been the source for the electronic sequencers used to replace the failure-prone mechanical motor driven turn signal sequencers. Member of the Cougar Club of America since 1981 and a founding member of the Cougar Club of New Mexico.

Parts Chart BARGANSPOT (an eBay store) www.barganspot.com

(All parts manufactured by Cougars Unlimited LLC)

 

1969 Cougar

Sequencer Board - C4L) C9WY-13A366-AL (LED or Incandescent bulbs)

Flasher can electronic, Incandescent systems - C6) DOWY-13350-AR (Incandescent bulbs)

TURN SIGNAL SWITCH - WITH TILT – C48) C8SZ-13341-BR (*LED bulbs only)

TURN SIGNAL SWITCH - WITHOUT TILT – C43) C9AZ-13341-BR (*LED bulbs only)

Headlight Switch with vacuum control - C73) C8WY-11654-AR

Starter Solenoid Pigtail Set Harness repair kit - C83) C9WB-14488-P

Flasher can electronic, LED systems - C6) DOWY-13350-L (LED bulbs)

Harness REPAIR kit – trunk sequencer side -  (C33 C9WY-13H366-AR

Front Turn Signal Bezel Harness pigtail (1 pair) C77B) C8WB-13234-AR

Dash to Engine Gauge feed - 390/427/428 – C63) D0AZ-14289-AR

Dash to Engine Gauge feed - 351W - C62) D4AZ-14289-RR

XR7 "Alternator wiring harness” - with ammeter – C30) C9ZZ-14305-SR

Standard "Alternator wiring harness” - without ammeter – C29) C9WY-14305-GR

Tilt column wiring harness – and flyaway – C28) C9ZZ-3D568

Standard “Dash Panel to Headlight” Wiring Harness - C25) C9WY-14290-AR

XR7 “Dash Panel to Headlight” Wiring Harness – C13) C9WY-14290-LR

Standard “Tail Light Wiring Harness with Sockets” – C76/C82) C9WY-14405-RR/C8WB-14406-BR

XR7 “Tail Light Wiring Harness with Sockets” – C76) C9WY-14405-RR

 

1970 Cougar

Sequencer Board - C4L) C9WY-13A366-AL (LED or Incandescent bulbs)

Flasher can electronic, Incandescent systems - C6) DOWY-13350-AR (Incandescent bulbs)

Flasher can electronic, LED systems - C6) DOWY-13350-L (LED bulbs)

TURN SIGNAL SWITCH - WITH TILT – C46) D2AZ-13341-DR (*LED bulbs only)

TURN SIGNAL SWITCH - WITHOUT TILT – C41) D2AZ-13341-CR (*LED bulbs only)

Headlight Switch with vacuum control - C73) C8WY-11654-AR

Starter Solenoid Pigtail Set Harness repair kit - C83) C9WB-14488-P

Harness REPAIR kit – trunk sequencer side -  (C33 C9WY-13H366-AR

Front Turn Signal Bezel Harness pigtail (1 pair) C77B) C8WB-13234-AR

Dash to Engine Gauge feed - 351C 2V/4V  - C64) D0ZZ-14289-AR

Dash to Engine Gauge feed - 390/427/428 – C63) D0AZ-14289-AR

Dash to Engine Gauge feed - 351W - C62) D4AZ-14289-RR

XR7 "Alternator wiring harness” - with ammeter – C69) DOZZ-14305-CR

Standard "Alternator wiring harness” – without ammeter – C68) DOWY-14305-CR

Side Marker LED Adapter Kit - C36) DOWY-15A434-LSM

 

!971 Cougar

Sequencer Board - C4L) C9WY-13A366-AL (LED or Incandescent bulbs)

Flasher can electronic, Incandescent systems - C6) DOWY-13350-AR (Incandescent bulbs)

Flasher can electronic, LED systems - C6) DOWY-13350-L (LED bulbs)

TURN SIGNAL SWITCH - WITH TILT – C46) D2AZ-13341-DR (*LED bulbs only)

TURN SIGNAL SWITCH - WITHOUT TILT – C41) D2AZ-13341-CR (*LED bulbs only)

Harness REPAIR kit – trunk sequencer side -  C33) C9WY-13H366-AR

Dash to Engine Gauge feed - 351C 2V/4V  - C21) D1OZ-14289-AR

XR7 "Alternator wiring harness” - with ammeter – C71) D1ZZ-14305-BR

Standard "Alternator wiring harness” – without ammeter – C70) D1OZ-14305-BR

Side Marker LED Adapter Kit – C78) D1WY-15A434-LSM

 

1972 Cougar

Sequencer Board - C4L) C9WY-13A366-AL (LED or Incandescent bulbs)

Flasher can electronic, Incandescent systems - C6) DOWY-13350-AR (Incandescent bulbs)

Flasher can electronic, LED systems - C6) DOWY-13350-L (LED bulbs)

TURN SIGNAL SWITCH - WITH TILT – C46) D2AZ-13341-DR (*LED bulbs only)

TURN SIGNAL SWITCH - WITHOUT TILT – C41) D2AZ-13341-CR (*LED bulbs only)

Harness REPAIR kit – trunk sequencer side -  (C33 C9WY-13H366-AR

 

1973 Cougar

Sequencer Board - C4L) C9WY-13A366-AL (LED or Incandescent bulbs)

Flasher can electronic, Incandescent systems - C6) DOWY-13350-AR (Incandescent bulbs)

Flasher can electronic, LED systems - C6) DOWY-13350-L (LED bulbs)

Harness REPAIR kit – trunk sequencer side -  (C33 C9WY-13H366-AR

*NOTE: TURN SIGNAL SWITCH – All turn signal switches sold by Cougars Unlimited LLC are for use with LED bulbs only. The reason for this is applicable vehicles are now over 50 years old the current that sequencing systems draw have greatly increased over time. This is because of the original wiring harnesses and connectors are deteriorating increasing the resistance. Higher the resistance the higher the current draw across the switch. The current is now so high on most vehicles that it exceeds the ratting of the switches, causing them to prematurely fail. The only solution is to convert to LED bulbs, they draw far less current. On vehicles that have converted to LED the turn signal switches are not failing. The only other solution is to replace the complete wiring harness which is expensive, and in most cases not possible.

When converting to LED bulbs Cougars Unlimited LLC strongly recommends using WCCC1157RPR (Red for rear) LED bulbs and WCCC1157YPR (Yellow for front) LED bulbs. They have a built in current limiting diode. This stops the reverse current flow that causes sequential turn signal systems to malfunction.