12MM PERFORMANCE MANIFOLD INSULATOR KIT FOR BUICK ENCLAVE ALLOYTEC LY7 3.6 V6

Exclusive to Mace Engineering, here we have our design-registered lower manifold insulators to suit Buick vehicles fitted with Alloytec LY7 3.6L V6 engine.

What are manifold insulators and what do they do?

Manifold insulators are a thermal insulating spacer that mount between your engine block and intake manifold. Made from a heat blocking composite, our manifold insulators will increase power from your engine by keeping the intake cooler and increase low end torque by increasing runner length.

But how do manifold insulators keep the intake manifold cooler?

Given our manifold insulators are made from a composite material with a thermal conductivity of 0.29 W/m*K as opposed to aluminium, which has a thermal conductivity of 150 W/m*K; The difference works out to be that aluminium conducts heat 500 times higher than our composite material!

Also, with gaskets often made out of steel (thermal conductivity of 20 W/m-K) placed between the upper and lower manifolds being 0.5mm thick, replacing them with a manifold insulator will conduct up to an amazing 3,448 times less heat depending on the size chosen.

Our composite material also exhibits high stiffness and compressive strength, can withstand temperatures up to 150°C, and has a thermal expansion coefficient very similar to aluminium to increase sealing capabilities. In addition, the spacer can also withstand boosted conditions with ease.

Dyno Results:

The following test was conducted on a 2007 model Holden Statesman, with a standard Alloytec 6. Looking at the graph, we can see that power produced down low had increased by a staggering 10%! While power also increased virtually across the entire rev range. Please note that these results don't reflect the true nature of the on road gains given the lack of actual airflow, which further drop inlet temps.

Under normal driving conditions the plenum (upper manifold), with the insulator in place, becomes cool enough to comfortably touch. Unlike before, without the manifold insulator installed under the same driving conditions, making it very difficult to touch without getting burnt!

POWER RUN, BEFORE AND AFTER MANIFOLD INSULATOR

Key Benefits:

• 10% gain in bottom end torque.
• Design registered.
• Reduces charge air temperature resulting in better power consistency and detonation prevention.
• Power increase with no undesirable side effects.
• Improved low end torque by increasing runner length.
• Improved fuel economy.
• Easy to install.
• Can be used as a replacement gasket.
• Reusable.
• Proven gains at an affordable price.

Contents:

• 1 X Bolt pack
• 1 X Silicone gasket maker
• 2 X Manifold insulator

Vehicle Fitment Guide

Notes:

• The Manifold Insulator may vary depending on engine design and model so we strongly recommend you look up your vehicle's engine code and match with the vehicle fitment guide, before proceeding with your purchase.
• This Manifold insulator kit does come with bolts however due to the large variances of the High Feature V6 engines, fitment of the bolts as well as the manifold insulators themselves, cannot be 100% guaranteed. If in doubt, please share photos and measurements of your vehicle's manifold runners and bolts with us only then we would be able to assist better.
  
• A 25mm manifold insulator can be purchased through another listing.

Please remember to check out our other performance products for sale

*You may receive an Address Confirmation email in case our system is unable to verify your delivery address based on our address database*

E2162

Returns Policy

At Mace Engineering Group, we take great care in packaging of your products appropriately to ensure that they arrive in perfect condition. If for any reason your product is damaged during shipment, please contact us immediately to arrange for the return of your product(s) within 14 days. We will then provide you with a replacement product as soon as possible.

If you receive a product with manufacturing defect, it must be returned within 14 days. After appropriate testing, if it is found that the defect is due to misuse, willful damage, unauthorized repair or tampering with the product by the customer, return will not be accepted by Mace Engineering Group. Strictly no returns/refunds will be given due to buyer's change of mind or remorse. This is in compliance to the ACCC warranties and refunds.

Re-Stocking Fee & Refunds

If a purchased item is returned due to buyer's remorse or misorder, 10-15% re-stocking fee will be applicable at our discretion, depending on the item.

Paypal has changed its refund policy and will no longer refund the fees deducted for the original transaction, therefore, Mace Engineering Group will deduct the 2% fee while making a partial or full refund other than the restocking fee, if applicable

Postage cost is non-refundable.

Domestic Orders

• Orders typically take 1-2 business days to prepare and process prior to dispatch.
• Freight may take 1-7 business days from the date of dispatch to delivery within Australia.
• Orders can also be picked up directly from us on business days. Please email us.
• Orders are neither dispatched nor delivered on weekends.

International Orders

• Shipping will be calculated automatically based on the delivery address.
• Orders outside of Australia may take up to 10 days.
• You will be responsible for any applicable taxes and/or duties and will need to be paid upon delivery.

**Saturday and Sunday ARE NOT business days**

Product Warranty

Mace Engineering Group products are covered by a 1 year warranty, unless otherwise specified in the ad or written agreement from Mace Engineering Group.

Terms of Warranty

Customer must return the defective item(s) first, with a full description of the problem. Appropriate tests will be conducted to determine the authenticity of the defects and claims. Once, Mace Engineering Group is satisfied, identical items(s) will be sent out to the customer.

Please ensure proper packaging of the product to prevent any damage while in transit, as goods are at owner's risk.