Item Description

• Wheel studs already installed
• Fits either LH (Driver Side) or RH (Passenger Side) Front and Rear
• Flange Bolt Hole Quantity: 4
• ABS Type: Encoder

Item Features

• Brand New Wheel Hub Assembly
• Direct replacement
• Built to strict quality control standards

Vehicle Fitment

• Fits Audi A4 Allroad 2013-2016 Front & Rear
• Fits Audi A4 Quattro 2009-2016 Front & Rear
• Fits Audi A5 Quattro 2008-2017 Front & Rear
• Fits Audi A6 Quattro 2012-2018 Front & Rear
• Fits Audi A7 Quattro 2012-2018 Front & Rear
• Fits Audi A8 Quattro 2013-2018 Front & Rear
• Fits Audi Allroad 2013-2016 Front & Rear
• Fits Audi Q5 2009-2017 Front & Rear
• Fits Audi RS5 2013-2016 Front & Rear
• Fits Audi RS7 2014-2018 Front & Rear
• Fits Audi S4 2010-2016 Front & Rear
• Fits Audi S5 2008-2017 Front & Rear
• Fits Audi S6 2013-2018 Front & Rear
• Fits Audi S7 2013-2018 Front & Rear
• Fits Audi S8 2013-2018 Front & Rear
• Fits Audi SQ5 2014-2017 Front & Rear

Item Include

• 4x wheel hub bearing

When do you need to replace

• Poor Clicking, snapping or popping
• Clunking or knocking
• Rumbling, humming or growling
• Wobble and/or wheel vibrations
• Shimmy, shudder, or vibration at constant speeds
• Abnormal side pulling when applying brakes
• Uneven or abnormal tire wear
• ABS failure

How to Install

• 1.Loosen the lug nuts on the wheel of the hub bearing you're replacing with the breaking bar and a socket
• 2.Lift the wheel with the floor jack in a safe and secure manner. Support the vehicle on a jack stand
• 3.Remove the lug nuts and wheel.Locate the caliper bolts and remove them with the ratchet and a socket.
• 4.Pry the caliper off gently using a large straight-edged screwdriver and support the caliper on the coil spring with a bungee cord.
• 5.Locate the caliper bridge bolts (if applicable) and remove them with the ratchet and a socket.
• 6.Remove any ABS wires attached to the hub bearing assembly (if applicable) or unclip the wire and trace it to the plug. 
• 7.Remove the spindle nut with the breaking bar and a spindle nut socket. Remove the washer behind the spindle nut.
• 8.Locate the wheel-bearing assembly bolts behind the knuckle, and loosen them with the breaking bar and socket. 
• 9.Install the slide hammer onto the lug studs and secure with tightened lug nuts.Sand off the rust and corrosion around the knuckle with a fine- to medium-grade sandpaper. 
• 10.Place the backing plate in its original position and place the new bearing onto the knuckle. Replace the wheel-bearing assembly bolts. 
• 11.Replace washer and spindle nut and tighten to proper torque specifications with the half-inch drive torque wrench and spindle socket.
• 12.Replace the brakes in the same manner you extracted them. the tire and lug nuts, and tighten the lug nuts as tight as you can get them.
• 13.Lower the vehicle and tighten the lug nuts in an alternate fashion with the torque wrench and socket at the correct wheel nut specifications torque setting.

Note

• If you have any question about the product, please contact us before buying, we will give you a best reply in time.
• We are galde to offer quality service and vehicle parts to you, any sale questions please message us before open case or feedback, we will give you the best solution.