🌦️ ESP32 Starter Kit: WiFi Weather Station (Learning Kit)
Description: Build your own WiFi weather station and learn the core skills behind almost every IoT project. An ESP32-C3 board reads temperature, humidity and air pressure, shows them on a 1.3" OLED screen, and hosts its own live web dashboard you can open on your phone. No soldering needed: every kit arrives soldered, flashed and self-tested, and the full code and guide are free and open source.
- ✅ Soldered, flashed and self-tested before dispatch — every kit passes its power-on self-test before it ships
- ✅ No soldering needed — headers already soldered, just plug the parts into the breadboard
- ✅ Works out of the box — comes pre-loaded with the weather station firmware and WiFi dashboard
- ✅ Free open-source code and step-by-step guide, written for beginners
- ✅ Tracked delivery included — Royal Mail Tracked 48
- ✅ UK stock, dispatched daily from our Callander workshop in Scotland
- ✅ Not a toy — a learning kit for makers aged 14+
🎓 What You'll Learn
- Wiring an I2C bus — how a sensor and a display share the same two data wires
- Using the Arduino IDE — installing the ESP32 board package and uploading code to real hardware
- Reading sensors — temperature, humidity and pressure, shown live on an OLED screen
- Building a WiFi dashboard — the board creates its own WiFi network and serves a live web page, no router or internet needed
- Checking your own work — a built-in self-test tells you straight away whether each part is wired correctly
- Going further — guided "Try this next" exercises, such as °F readings, min/max tracking and altitude
📦 What's in the Box
- 1x ESP32-C3 SuperMini — WiFi + Bluetooth LE dev board with USB-C, headers soldered, WiFi dashboard version of the firmware pre-loaded
- 1x AHT20 + BMP280 sensor module — temperature, humidity and air pressure on one board, headers soldered
- 1x 1.3" OLED display — 128x64 pixels, white, SH1106 driver, I2C, headers soldered
- 1x MB-102 830-point solderless breadboard — with self-adhesive backing
- 8x male-to-male Dupont jumper wires — enough to connect the sensor and the display
Not included: USB-C cable and USB power. We leave the cable out on purpose to cut e-waste, as most homes already have one: any USB-C phone cable plus a phone charger or computer USB port works. A computer is only needed if you want to change or re-upload the code.
⚡ Kit Specifications
- Microcontroller: ESP32-C3 (32-bit RISC-V, 160MHz, 4MB flash)
- Wireless: 2.4GHz WiFi (own access point) + Bluetooth LE 5
- Power: 5V via the USB-C port
- Temperature / Humidity: AHT20, ±0.3°C / ±2% RH typical
- Air Pressure: BMP280, 300-1100 hPa, ±1 hPa typical
- Display: 1.3" OLED, 128x64, SH1106, I2C address 0x3C
- Interface: I2C on GPIO 8 (SDA) and GPIO 9 (SCL)
- Update Rate: every 2 seconds, on the screen and the web dashboard
- Programming: free Arduino IDE (Windows, macOS, Linux) with the ESP32 board package
🧭 Getting Started
- Press the three boards into the breadboard and connect them with the jumper wires, following the wiring below (a full wiring diagram is in the free guide).
- Power the ESP32 board with a USB-C cable. The screen shows the ElTech-Online logo, then your kit's WiFi details, then the live readings. If a wire is loose, it shows a SELF-TEST FAILED screen telling you which part to check.
- On your phone, join the WiFi network shown at the top of the screen (the name and password are unique to your kit), then open http://192.168.4.1 for the live dashboard.
- Ready to code? Follow the free guide (address on the card in the box) to install the Arduino IDE, read how the code works, and try the exercises.
Wiring (all parts share one I2C bus):
- 3.3V: ESP32 3V3 → sensor VDD and display VDD
- GND: ESP32 GND → sensor GND and display GND
- SDA: ESP32 GPIO 8 → sensor SDA and display SDA
- SCL: ESP32 GPIO 9 → sensor SCL and display SCK
💻 Free Code & Step-by-Step Guide
The full source code, wiring diagram and guide are free and open source. The web address is printed on the quick-start card in the box, or message us through eBay and we'll send it straight away.
- Two ready-made versions: display only, and display + WiFi dashboard
- Wiring diagram and pin table
- Arduino IDE setup with the exact settings and library versions we test with
- An I2C scanner to find your pins and addresses
- A plain-English walkthrough of how the code works, plus exercises to try next
🔬 Tested Before It Ships
Every kit is built and checked by hand in our workshop before dispatch:
- Headers soldered onto the ESP32 board and the sensor module.
- The kit is wired up on its breadboard, exactly as you will build it.
- The firmware is uploaded and its power-on self-test must report PASS: display found, and sensible temperature, humidity and pressure readings.
- We join the kit's own WiFi network from a phone and check the live dashboard loads.
⚠️ Safety & Best Practice
- Not a toy. This is an electronics learning kit for makers aged 14+. Younger builders need adult supervision. Contains small parts — keep away from young children.
- Readings a little warm? The ESP32 warms up while running, so a sensor right next to it reads roughly 1-3°C high. Place the sensor a few centimetres away from the board, beside or below it, for more accurate readings.
- Use 3.3V, not 5V, for the sensor and display power wires, as shown in the wiring guide.
- Unplug the USB cable before rewiring to avoid accidental short circuits.
- Handle boards by their edges and store them in the supplied ESD bags when not in use.
🔄 Returns & Support
This listing has a 30-day return window. If your item arrives faulty or dead-on-arrival, just message us — we typically reply within 24 hours and will sort a replacement or a full refund, no fuss.
New to electronics or stuck on a step? Message us before leaving feedback — we built and tested this kit ourselves and are happy to help you get it working.
💷 Save More When You Buy Multiples
- Buy 2 — save 5%
- Buy 3 — save 10%
- Buy 4 or more — save 15%
Discounts are applied automatically at checkout — just add the quantity you need to your basket.
🚚 Shipping & Delivery Information
- Free UK delivery by Royal Mail Tracked 48
- Fast daily dispatch from our workshop in Callander, Scotland
- Boards packed in anti-static ESD bags inside defensive packaging so the pins arrive straight and undamaged
🛠️ Complete Your Project Build